Analytical Evaluation of Energy and Throughput for Multilevel Caches

With the increase of processor-memory performance gap, it has become important to gauge the performance of cache architectures so as to evaluate their impact on energy requirement and throughput of the system. Multilevel caches are found to be increasingly prevalent in the high-end processors. Additionally, the recent drive towards multicore systems has necessitated the use of multilevel cache hierarchies for shared memory architectures. This paper presents simplified and accurate mathematical models to estimate the energy consumption and the impact on throughput for multilevel caches for single core systems

Near-optimal precharging in high-performance nanoscale CMOS caches

High-performance caches statically pull up the bit-lines in all cache subarrays to optimize cache access latency. Unfortunately, such architecture results in a significant waste of energy in nanoscale CMOS implementations due to high leakage and bitline discharge in the unaccessed subarrays. Recent research advocates bitline isolation to control precharging of individual subarrays using bitline precharge devices. In this paper, we carefully evaluate the energy and performance trade-offs of bitline isolation, and propose a technique to exploit nearly its full potential to eliminate discharge and reduce overall energy in level-one caches. Cycle-accurate and circuit simulation results of a wide-issue superscalar processor indicate that: 1) in future CMOS technologies (e.g., 70 nm and beyond), cache architectures that exploit bitline isolation can eliminate up to 90% of the bitline discharge; 2) on- demand precharging (i.e., decoding the address and subsequently precharging the accessed subarrays) is not viable in level-one caches because precharging increases the cache access latency; and 3) our proposal for gated precharging to exploit subarray reference locality and precharging only the recently accessed subarrays eliminates nearly all of bitline discharge in nanoscale CMOS caches with only a 1% of performance degradatio

Affordable techniques for dependable microprocessor design

As high computing power is available at an affordable cost, we rely on microprocessor-based systems for much greater variety of applications. This dependence indicates that a processor failure could have more diverse impacts on our daily lives. Therefore, dependability is becoming an increasingly important quality measure of microprocessors.;Temporary hardware malfunctions caused by unstable environmental conditions can lead the processor to an incorrect state. This is referred to as a transient error or soft error. Studies have shown that soft errors are the major source of system failures. This dissertation characterizes the soft error behavior on microprocessors and presents new microarchitectural approaches that can realize high dependability with low overhead.;Our fault injection studies using RISC processors have demonstrated that different functional blocks of the processor have distinct susceptibilities to soft errors. The error susceptibility information must be reflected in devising fault tolerance schemes for cost-sensitive applications. Considering the common use of on-chip caches in modern processors, we investigated area-efficient protection schemes for memory arrays. The idea of caching redundant information was exploited to optimize resource utilization for increased dependability. We also developed a mechanism to verify the integrity of data transfer from lower level memories to the primary caches. The results of this study show that by exploiting bus idle cycles and the information redundancy, an almost complete check for the initial memory data transfer is possible without incurring a performance penalty.;For protecting the processor\u27s control logic, which usually remains unprotected, we propose a low-cost reliability enhancement strategy. We classified control logic signals into static and dynamic control depending on their changeability, and applied various techniques including commit-time checking, signature caching, component-level duplication, and control flow monitoring. Our schemes can achieve more than 99% coverage with a very small hardware addition. Finally, a virtual duplex architecture for superscalar processors is presented. In this system-level approach, the processor pipeline is backed up by a partially replicated pipeline. The replication-based checker minimizes the design and verification overheads. For a large-scale superscalar processor, the proposed architecture can bring 61.4% reduction in die area while sustaining the maximum performance

Null convention logic circuits for asynchronous computer architecture

For most of its history, computer architecture has been able to benefit from a rapid scaling in semiconductor technology, resulting in continuous improvements to CPU design. During that period, synchronous logic has dominated because of its inherent ease of design and abundant tools. However, with the scaling of semiconductor processes into deep sub-micron and then to nano-scale dimensions, computer architecture is hitting a number of roadblocks such as high power and increased process variability. Asynchronous techniques can potentially offer many advantages compared to conventional synchronous design, including average case vs. worse case performance, robustness in the face of process and operating point variability and the ready availability of high performance, fine grained pipeline architectures. Of the many alternative approaches to asynchronous design, Null Convention Logic (NCL) has the advantage that its quasi delay-insensitive behavior makes it relatively easy to set up complex circuits without the need for exhaustive timing analysis. This thesis examines the characteristics of an NCL based asynchronous RISC-V CPU and analyses the problems with applying NCL to CPU design. While a number of university and industry groups have previously developed small 8-bit microprocessor architectures using NCL techniques, it is still unclear whether these offer any real advantages over conventional synchronous design. A key objective of this work has been to analyse the impact of larger word widths and more complex architectures on NCL CPU implementations. The research commenced by re-evaluating existing techniques for implementing NCL on programmable devices such as FPGAs. The little work that has been undertaken previously on FPGA implementations of asynchronous logic has been inconclusive and seems to indicate that asynchronous systems cannot be easily implemented in these devices. However, most of this work related to an alternative technique called bundled data, which is not well suited to FPGA implementation because of the difficulty in controlling and matching delays in a 'bundle' of signals. On the other hand, this thesis clearly shows that such applications are not only possible with NCL, but there are some distinct advantages in being able to prototype complex asynchronous systems in a field-programmable technology such as the FPGA. A large part of the value of NCL derives from its architectural level behavior, inherent pipelining, and optimization opportunities such as the merging of register and combina- tional logic functions. In this work, a number of NCL multiplier architectures have been analyzed to reveal the performance trade-offs between various non-pipelined, 1D and 2D organizations. Two-dimensional pipelining can easily be applied to regular architectures such as array multipliers in a way that is both high performance and area-efficient. It was found that the performance of 2D pipelining for small networks such as multipliers is around 260% faster than the equivalent non-pipelined design. However, the design uses 265% more transistors so the methodology is mainly of benefit where performance is strongly favored over area. A pipelined 32bit x 32bit signed Baugh-Wooley multiplier with Wallace-Tree Carry Save Adders (CSA), which is representative of a real design used for CPUs and DSPs, was used to further explore this concept as it is faster and has fewer pipeline stages compared to the normal array multiplier using Ripple-Carry adders (RCA). It was found that 1D pipelining with ripple-carry chains is an efficient implementation option but becomes less so for larger multipliers, due to the completion logic for which the delay time depends largely on the number of bits involved in the completion network. The average-case performance of ripple-carry adders was explored using random input vectors and it was observed that it offers little advantage on the smaller multiplier blocks, but this particular timing characteristic of asynchronous design styles be- comes increasingly more important as word size grows. Finally, this research has resulted in the development of the first 32-Bit asynchronous RISC-V CPU core. Called the Redback RISC, the architecture is a structure of pipeline rings composed of computational oscillations linked with flow completeness relationships. It has been written using NELL, a commercial description/synthesis tool that outputs standard Verilog. The Redback has been analysed and compared to two approximately equivalent industry standard 32-Bit synchronous RISC-V cores (PicoRV32 and Rocket) that are already fabricated and used in industry. While the NCL implementation is larger than both commercial cores it has similar performance and lower power compared to the PicoRV32. The implementation results were also compared against an existing NCL design tool flow (UNCLE), which showed how much the results of these implementation strategies differ. The Redback RISC has achieved similar level of throughput and 43% better power and 34% better energy compared to one of the synchronous cores with the same benchmark test and test condition such as input sup- ply voltage. However, it was shown that area is the biggest drawback for NCL CPU design. The core is roughly 2.5× larger than synchronous designs. On the other hand its area is still 2.9× smaller than previous designs using UNCLE tools. The area penalty is largely due to the unavoidable translation into a dual-rail topology when using the standard NCL cell library

Power Management for Deep Submicron Microprocessors

As VLSI technology scales, the enhanced performance of smaller transistors comes at the expense of increased power consumption. In addition to the dynamic power consumed by the circuits there is a tremendous increase in the leakage power consumption which is further exacerbated by the increasing operating temperatures. The total power consumption of modern processors is distributed between the processor core, memory and interconnects. In this research two novel power management techniques are presented targeting the functional units and the global interconnects. First, since most leakage control schemes for processor functional units are based on circuit level techniques, such schemes inherently lack information about the operational profile of higher-level components of the system. This is a barrier to the pivotal task of predicting standby time. Without this prediction, it is extremely difficult to assess the value of any leakage control scheme. Consequently, a methodology that can predict the standby time is highly beneficial in bridging the gap between the information available at the application level and the circuit implementations. In this work, a novel Dynamic Sleep Signal Generator (DSSG) is presented. It utilizes the usage traces extracted from cycle accurate simulations of benchmark programs to predict the long standby periods associated with the various functional units. The DSSG bases its decisions on the current and previous standby state of the functional units to accurately predict the length of the next standby period. The DSSG presents an alternative to Static Sleep Signal Generation (SSSG) based on static counters that trigger the generation of the sleep signal when the functional units idle for a prespecified number of cycles. The test results of the DSSG are obtained by the use of a modified RISC superscalar processor, implemented by SimpleScalar, the most widely accepted open source vehicle for architectural analysis. In addition, the results are further verified by a Simultaneous Multithreading simulator implemented by SMTSIM. Leakage saving results shows an increase of up to 146% in leakage savings using the DSSG versus the SSSG, with an accuracy of 60-80% for predicting long standby periods. Second, chip designers in their effort to achieve timing closure, have focused on achieving the lowest possible interconnect delay through buffer insertion and routing techniques. This approach, though, taxes the power budget of modern ICs, especially those intended for wireless applications. Also, in order to achieve more functionality, die sizes are constantly increasing. This trend is leading to an increase in the average global interconnect length which, in turn, requires more buffers to achieve timing closure. Unconstrained buffering is bound to adversely affect the overall chip performance, if the power consumption is added as a major performance metric. In fact, the number of global interconnect buffers is expected to reach hundreds of thousands to achieve an appropriate timing closure. To mitigate the impact of the power consumed by the interconnect buffers, a power-efficient multi-pin routing technique is proposed in this research. The problem is based on a graph representation of the routing possibilities, including buffer insertion and identifying the least power path between the interconnect source and set of sinks. The novel multi-pin routing technique is tested by applying it to the ISPD and IBM benchmarks to verify the accuracy, complexity, and solution quality. Results obtained indicate that an average power savings as high as 32% for the 130-nm technology is achieved with no impact on the maximum chip frequency

Deep-submicron embedded processor architectures for high-performance, low-cost and low-power

Because the market has an insatiable appetite for new functionality, performance is becoming an increasingly important factor. The telecommunication and network domains are especially touched by this phenomenon but they are not the only ones. For instance, the automotive applications are also affected by the passion around the electronic devices that are programmable. This thesis work will focus on embedded applications based on programmable processing unit. Indeed, nowadays, for time to market reasons, re-use and flexibility are important parameters. Consequently, embedded processors seem to be the solution because the behavior of the circuit can be modified by software what does not cost a lot compared to Application Specific Integrated Circuits (ASICs) or Digital Signal Processors (DSPs) where hardware modifications are necessary. This choice is judicious compared to multi-pipeline processors like superscalar or Very Long Instruction Word (VLIW) architectures or even in comparison to a Field Programmable Gate Array (FPGA) which require more silicon area, consume more energy and are not as robust as simple scalar processors. Nevertheless, commercial scalar processors, dedicated to embedded systems, have poor frequencies which has a negative effect on their performance. This phenomenon is even more visible with deep-submicron technologies where the primary memories and wire delays do not scale as fast as the logic. Furthermore, the memory speed decreases when their capacity of storage increases and depends on both their organization (associativity, word size, etc.) and the IPs of the foundry. Likewise, synthesizable IP memories have a greater access time than their hard macrocell counterparts. This thesis work proposes a new synthesizable architecture for scalar embedded processors dedicated to alleviate the drawbacks previously mentioned and called Memory Wall : so, its goal is to push back the limits of frequency without introducing wasted cycles used to solve data and control dependencies, independently of the foundry. The architecture that came out, called Deep Submicron RISC (DSR), is made up of a single pipeline with eight stages that executes the instructions in order. In addition to tackle the memory access time and to alleviate the delays of wires, it is appropriate to minimize the power consumption. The proposed architecture is compared to two MIPS architectures, the MIPS R3000 and the MIPS32 24k in order to be able to analyze the performance of the architectures themselves, independently of both Instruction Set (ISA) MIPS 1 and compiler. The R3000 is a processor born in the 90's and the 24k came out in 2004. Obviously, the study reveals that the five-stage processor remains efficient – especially in comparison to the MIPS24k – when the critical path passes by the core and not by the primary memories. Even if the MIPS24k tackles in part the Memory Wall, DSR is much more efficient and reach a gain of efficiency – defined as performance/surface – of 72% thanks to its High-density version (DSR-HD) compared to a five-stage processor. DSR is even more efficient than the two MIPS processors when the transistor channel length decreases, the wire delays are important or the memories are large and their organization complex

Tiled microprocessors

Thesis (Ph. D.)--Massachusetts Institute of Technology, Dept. of Electrical Engineering and Computer Science, 2007.Includes bibliographical references (p. 251-258).Current-day microprocessors have reached the point of diminishing returns due to inherent scalability limitations. This thesis examines the tiled microprocessor, a class of microprocessor which is physically scalable but inherits many of the desirable properties of conventional microprocessors. Tiled microprocessors are composed of an array of replicated tiles connected by a special class of network, the Scalar Operand Network (SON), which is optimized for low-latency, low-occupancy communication between remote ALUs on different tiles. Tiled microprocessors can be constructed to scale to 100's or 1000's of functional units. This thesis identifies seven key criteria for achieving physical scalability in tiled microprocessors. It employs an archetypal tiled microprocessor to examine the challenges in achieving these criteria and to explore the properties of Scalar Operand Networks. The thesis develops the field of SONs in three major ways: it introduces the 5-tuple performance metric, it describes a complete, high-frequency SON implementation, and it proposes a taxonomy, called AsTrO, for categorizing them.(cont.) To develop these ideas, the thesis details the design, implementation and analysis of a tiled microprocessor prototype, the Raw Microprocessor, which was implemented at MIT in 180 nm technology. Overall, compared to Raw, recent commercial processors with half the transistors required 30x as many lines of code, occupied 100x as many designers, contained 50x as many pre-tapeout bugs, and resulted in 33x as many post-tapeout bugs. At the same time, the Raw microprocessor proves to be more versatile in exploiting ILP, stream, and server-farm workloads with modest to large amounts of parallelism.by Michael Bedford Taylor.Ph.D