Receiver architecture of the thousand-element array (THEA)

As part of the development of a new international radio-telescope SKA (Square Kilometre Array), an outdoor phasedarray prototype, the THousand Element Array (THEA), is being developed at NFRA. THEA is a phased array with 1024 active elements distributed on a regular grid over a surface of approximately 16 m2. The array is organised into 16 units denoted as tiles. THEA operates in the frequency band from 750 to 1500 MHz.\ud On a tile the signals from 64 antenna elements are converted into two independent RF beams. Two times 16 beams can be made simultaneously with full sensitivity by the real-time digital beam former of the THEA system. At the output of each tile the analog RF signal from a beam is converted into a 2 × 12-bit digital quadrature representation by a receiver system.\ud A double super-heterodyne architecture is used to mix the signal band of interest to an intermediate frequency of 210 MHz. The IF-signal is shifted to baseband by means of a partly digitally implemented I/Q mixer scheme. After a quadrature mixer stage, the I and Q signals are digitised by means of 12 bit A/D converters at 40 MS/s. Implementing a part of the mixing scheme digitally offers the flexibility to use different I/Q architectures, e.g. Hartley and Weaver mixer setups. This way the effect of RFI in different mixing architectures can be analyzed. After the digital processing, the samples are multiplexed, serialised and transported over fibres to the central adaptive digital beam former unit where the signals from all tiles are combined giving 32 beams.\ud This paper focuses on the design choices and the final implementation of the THEA system. In particular, the receiver architecture is addressed. A digital solution is presented, which enables switching between a Hartley and a Weaver based mixer scheme

Low complexity blind and data-aided IQ imbalance compensation methods for low-IF receivers

Low-IF and Zero-IF (direct conversion) down converters showed a great potential in implementing multi standard single chip solutions, eliminating the need to use off chip components and so reduce the area and the cost of the wireless receivers. One of the main performance limitations in the low-IF & Zero-IF down-converters is the components mismatch between the in-phase path and the quadrature-path named the IQ Imbalance (IQI) which limits the achievable image rejection ratio (IRR) of the down converters. Many techniques had been proposed to enhance the achievable IRR either by using calibration methods, e.g. using lab calibration, or by doing online compensation during signal reception. In this work those techniques are reviewed, proposing three new methods for blind IQI compensation techniques, the first proposed method targets the low input signal to interference ratio (low SIRin) while the second and third methods targets the moderate and high SIRin, showing that the proposed methods reach better performance and/or lower complexity than the methods already introduced in the literature. Also two techniques to perform data aided IQI compensation are introduced exploiting pilot symbols within the desired signal with no prior knowledge about the image signal. The first method exploits a preamble sequence assuming slow fading condition while the second approach exploits a sequence of pilots to compensate for the IQI being suitable for fast fading conditions as well. Simulation results showed that the proposed data aided techniques achieved shorter convergence time and higher image rejection ratio compared to the blind methods at high SNR values

Quadrature Phase-Domain ADPLL with Integrated On-line Amplitude Locked Loop Calibration for 5G Multi-band Applications

5th generation wireless systems (5G) have expanded frequency band coverage with the low-band 5G and mid-band 5G frequencies spanning 600 MHz to 4 GHz spectrum. This dissertation focuses on a microelectronic implementation of CMOS 65 nm design of an All-Digital Phase Lock Loop (ADPLL), which is a critical component for advanced 5G wireless transceivers. The ADPLL is designed to operate in the frequency bands of 600MHz-930MHz, 2.4GHz-2.8GHz and 3.4GHz-4.2GHz. Unique ADPLL sub-components include: 1) Digital Phase Frequency Detector, 2) Digital Loop Filter, 3) Channel Bank Select Circuit, and 4) Digital Control Oscillator. Integrated with the ADPLL is a 90-degree active RC-CR phase shifter with on-line amplitude locked loop (ALL) calibration to facilitate enhanced image rejection while mitigating the effects of fabrication process variations and component mismatch. A unique high-sensitivity high-speed dynamic voltage comparator is included as a key component of the active phase shifter/ALL calibration subsystem. 65nm CMOS technology circuit designs are included for the ADPLL and active phase shifter with simulation performance assessments. Phase noise results for 1 MHz offset with carrier frequencies of 600MHz, 2.4GHz, and 3.8GHz are -130, -122, and -116 dBc/Hz, respectively. Monte Carlo simulations to account for process variations/component mismatch show that the active phase shifter with ALL calibration maintains accurate quadrature phase outputs when operating within the frequency bands 600MHz-930MHz, 2.4GHz-2.8GHz and 3.4GHz-4.2GHz

Polyphase filter with parametric tuning

Tese de mestrado integrado. Engenharia Electrotécnica e de Computadores. Faculdade de Engenharia. Universidade do Porto. 201

Digital PLL for ISM applications

In modern transceivers, a low power PLL is a key block. It is known that with the evolution of technology, lower power and high performance circuitry is a challenging demand. In this thesis, a low power PLL is developed in order not to exceed 2mW of total power consumption. It is composed by small area blocks which is one of the main demands. The blocks that compose the PLL are widely abridged and the final solution is shown, showing why it is employed. The VCO block is a Current-Starved Ring Oscillator with a frequency range from 400MHz to 1.5GHz, with a 300μW to approximately 660μW power consumption. The divider is composed by six TSPC D Flip-Flop in series, forming a divide-by-64 divider. The Phase-Detector is a Dual D Flip-Flop detector with a charge pump. The PLL has less than a 2us lock time and presents a output oscillation of 1GHz, as expected. It also has a total power consumption of 1.3mW, therefore fulfilling all the specifications. The main contributions of this thesis are that this PLL can be applied in ISM applications due to its covering frequency range and low cost 130nm CMOS technology

Multi-stage noise shaping (MASH) delta-sigma modulators for wideband and multi-standard applications

Imperial Users onl

Design and Implementation of a Re-Configurable Arbitrary Signal Generator and Radio Frequency Spectrum Analyser

This research is focused on the design, simulation and implementation of a reconfigurable arbitrary signal generator and the design, simulation and implementation of a radio frequency spectrum analyser based on digital signal processing. Until recently, Application Specific Integrated Circuits (ASICs) were used to produce high performance re-configurable function and arbitrary waveform generators with comprehensive modulation capabilities. However, that situation is now changing with the availability of advanced but low cost Field Programmable Gate Arrays (FPGAs), which could be used as an alternative to ASICs in these applications. The availability of high performance FPGA families opens up the opportunity to compete with ASIC solutions at a fraction of the development cost of an ASIC solution. A fast digital signal processing algorithm for digital waveform generation, using primarily but not limited to Direct Digital Synthesis (DDS) technologies, developed and implemented in a field-configurable logic, with control provided by an embedded microprocessor replacing a high cost ASIC design appeared to be a very attractive concept. This research demonstrates that such a concept is feasible in its entirety. A fully functional, low-complexity, low cost, pulse, Gaussian white noise and DDS based function and arbitrary waveform generator, capable of being amplitude, frequency and phase modulated by an internally generated or external modulating signal was implemented in a low-cost FPGA. The FPGA also included the capabilities to perform pulse width modulation and pulse delay modulation on pulse waveforms. Algorithms to up-convert the sampling rate of the external modulating signal using Cascaded Integrator Comb (CIC) filters and using interpolation method were analysed. Both solutions were implemented to compare their hardware complexities. Analysis of generating noise with user-defined distribution is presented. The ability of triggering the generator by an internally generated or an external event to generate a burst of waveforms where the time between the trigger signal and waveform output is fixed was also implemented in the FPGA. Finally, design of interface to a microprocessor to provide control of the versatile waveform generator was also included in the FPGA. This thesis summarises the literature, design considerations, simulation and implementation of the generator design. The second part of the research is focused on radio frequency spectrum analysis based on digital signal processing. Most existing spectrum analysers are analogue in nature and their complexity increases with frequency. Therefore, the possibility of using digital techniques for spectrum analysis was considered. The aim was to come up with digital system architecture for spectrum analysis and to develop and implement the new approach on a suitable digital platform. This thesis analyses the current literature on shifting algorithms to remove spurious responses and highlights its drawbacks. This thesis also analyses existing literature on quadrature receivers and presents novel adaptation of the existing architectures for application in spectrum analysis. A wide band spectrum analyser receiver with compensation for gain and phase imbalances in the Radio Frequency (RF) input range, as well as compensation for gain and phase imbalances within the Intermediate Frequency (IF) pass band complete with Resolution Band Width (RBW) filtering, Video Band Width (VBW) filtering and amplitude detection was implemented in a low cost FPGA. The ability to extract the modulating signal from a frequency or amplitude modulated RF signal was also implemented. The same family of FPGA used in the generator design was chosen to be the digital platform for this design. This research makes arguments for the new architecture and then summarises the literature, design considerations, simulation and implementation of the new digital algorithm for the radio frequency spectrum analyser

Multi-standard RF front-end for avionic systems

Aerodynamic issues such as drag, weight and aeroacoustic noise are important factors in evaluating the impact of a given antenna on an aircraft’s overall performance. These factors are directly related to aircraft fuel consumption, speed and range. This project’s focus is on RF front-end electronics. The main goal here is to bring aircraft radio equipment as close as possible to the antennas in order to minimize wiring weight and complexity. This calls for a drastic volume reduction of the radio equipment. To this end, the system level requirements for the RF front-ends in terms of frequency bandwidths, data rates, etc, are first investigated in order to identify applications where the proposed volume reductions are the most beneficial and feasible. Following this, the focus was on an architectural investigation of alternative topologies that can meet the specification. For each topology considered the front-end-level specification need to be translated to circuit/component level requirements. For each case, performance, cost and technical risk analyses are carried out. Then, the design and prototyping of key RF front-end circuits for the selected architecture are undertaken. The multilayered Low Temperature Co-fired Ceramic (LTCC) technology had to be considered as a high risk but more advantageous option in terms of volume/weight reduction. Finally, we aimed at integrating and testing the proposed RF front-end chain, first by characterizing each component individually, and then as a whole front-end subsystem