A Novel Design Optimization of a Fault-Tolerant AC Permanent Magnet Machine-Drive System

In this dissertation, fault-tolerant capabilities of permanent magnet (PM) machines were investigated. The 12-slot 10-pole PM machines with V-type and spoke-type PM layouts were selected as candidate topologies for fault-tolerant PM machine design optimization problems. The combination of 12-slot and 10-pole configuration for PM machines requires a fractional-slot concentrated winding (FSCW) layout, which can lead to especially significant PM losses in such machines. Thus, a hybrid method to compute the PM losses was investigated, which combines computationally efficient finite-element analysis (CE-FEA) with a new analytical formulation for PM eddy-current loss computation in sine-wave current regulated synchronous PM machines. These algorithms were applied to two FSCW PM machines with different circumferential and axial PM block segmentation arrangements. The accuracy of this method was validated by results from 2D and 3D time-stepping FEA. The CE-FEA approach has the capabilities of calculating torque profiles, induced voltage waveforms, d and q-axes inductances, torque angle for maximum torque per ampere load condition, and stator core losses. The implementation techniques for such a method are presented. A combined design optimization method employing design of experiments (DOE) and differential evolution (DE) algorithms was developed. The DOE approaches were used to perform a sensitivity study from which significant independent design variables were selected for the DE design optimization procedure. Two optimization objectives are concurrently considered for minimizing material cost and power losses. The optimization results enabled the systematic comparison of four PM motor topologies: two different V-shape, flat bar-type and spoke-type, respectively. A study of the relative merits of each topology was determined. An automated design optimization method using the CE-FEA and DE algorithms was utilized in the case study of a 12-slot 10-pole PM machine with V-type PM layout. An engineering decision process based on the Pareto-optimal front for two objectives, material cost and losses, is presented together with discussions on the tradeoffs between cost and performance. One optimal design was finally selected and prototyped. A set of experimental tests, including open circuit tests at various speeds and on-load tests under various load and speed conditions, were performed successfully, which validated the findings of this work

Traction axial flux motor-generator for hybrid electric bus application

Tato dizertační práce se zabývá návrhem původního motor-generátoru s axiálním tokem a buzením permanetními magnety, zkonstruovaným specificky pro hybridní elektrický autobus. Návrhové zadání pro tento stroj přineslo požadavky, které vedly k této unikátní topologii tak, aby byl dosažen výkon, účinnost a rozměry stroje. Tato partikulární topologie motor-generátoru s axiálním tokem je výsledkem literární rešerše, kterou následoval výběr koncepce stroje s představeným návrhem jako výsledkem těchto procesů. Přístup k návrhu stroje s axiálním tokem sledoval „multi-fyzikální“ koncepci, která pracuje s návrhem elektromagnetickým, tepelným, mechanickým, včetně návrhu řízení, v jedné iteraci. Tím je v konečném návrhu zajištěna rovnováha mezi těmito inženýrskými disciplínami. Pro samotný návrh stroje byla vyvinuta sada výpočtových a analytických nástrojů, které byly podloženy metodou konečných prvků tak, aby samotný návrh stroje byl přesnější a spolehlivější. Modelování somtného elektrického stroje a celého pohonu poskytlo představu o výkonnosti a účinnosti celého subsytému v rozmanitých operačních podmínkách. Rovněž poukázal na optimizační potenciál pro návrh řízení subsystému ve smyslu maximalizace účinnosti celého pohonu. Bylo postaveno několik prototypů tohoto stroje, které prošly intensivním testováním jak na úrovni sybsytému, tak systému. Samotné výsledky testů jsou diskutovány a porovnány s analytickými výpočty parametrů stroje. Poznatky získané z prvního prototypu stroje pak sloužily k představení možností, jak zjednodušit výrobu a montáž stroje v příští generaci. Tato práce zaznamenává jednotlivé kroky během všech fází vývoje elektrického stroje s axiálním tokem, počínaje výběrem konceptu stroje, konče sumarizací zkušeností získaných z první generace prototypu tohoto stroje.This thesis deals with a design of a novel Axial-Flux Permanent Magnet Motor-Generator for a hybrid electric bus application. Thus, the design specification represents a set of requirements, which leads toward a concept of a unique topology meeting performance, efficiency and dimensional targets. The particular topology of the Axial-Flux Permanent Magnet Motor-Generator discussed in this work is an outcome of deep literature survey, followed by the concept selection stage with the layout of the machine as an outcome of this processes. The design approach behind this so-called Spoke Axial-Flux Machine follows an idea of multiphysics iterations, including electromagnetic, thermal, mechanical and controls design. Such a process behind the eventually proposed design ensured a right balance in between all of these engineering disciplines. A set of bespoke design and analysis tools was developed for that reason, and was backed up by extensive use of Finite-Element Analysis and Computational Fluid Dynamics. Therefore, the actual machine design gained higher level of confidence and fidelity. Modelling of the machine and its drive provided understanding of performance and efficiency of the whole subsystem at various operational conditions. Moreover, it has illustrated an optimization potential for the controls design, so that efficiency of the machine and power electronics might be maximized. Several prototypes of this machine have been built and passed through extensive testing both on the subsystem and system level. Actual test results are discussed, and compared to analytical predictions in terms of the machine's parameters. As a lesson learned from the first prototype of this machine, a set of redesign proposals aiming for simplification of manufacturing and assembly processes, are introduced. This work records steps behind all phases of development of the Axial Flux Machine from a basic idea as an outcome of concept selection stage, up to testing and wrap-up of experience gained from the first generation of the machine.

Sensorless Commissioning and Control of High Anisotropy Synchronous Motor Drives

L'abstract è presente nell'allegato / the abstract is in the attachmen

Numerical Investigations of Air Flow and Heat Transfer in Axial Flux Permanent Magnet Electrical Machines

In this study an investigation of heat transfer in air cooled Axial Flux Permanent Magnet (AFPM) electrical machines is carried out. Efficiency of electrical machines is strongly influenced by an effective cooling which is provided by forced convection: air enters the generator through the opening in the machine enclosure and leaves it radially, as it is forced out by the rotating discs. The main goal is the enhancement of the heat transfer from the stator where heat is generated in the copper windings. On the other hand the heat transfer to the rotor needs to be minimised in order to keep the magnets' temperature as low as possible. The cooling can be improved by acting on design parameters, such as the distance between the stator and the rotors (commonly named running clearance), the magnet depth, and by acting on operational parameters, such as the rotational speed. The investigation is carried out by using Computational Fluid Dynamics (CFD) software to model air flow and heat transfer inside the AFPM machines. The experimental validation of the numerical models confirmed the capability of the CFD software in predicting the air mass flow rate and the heat transfer in the AFPM machines. The thesis describes the effects of the above mentioned parameters on target quantities, such as the heat transfer coefficients on the generator surfaces, the air mass flow rate through the machine, and the resistive torque. General correlations in non-dimensional form are obtained for the calculation of the heat transfer on the generator surfaces in the AFPM machines as a function of the above parameters. General correlations have also been obtained for the calculations of the non-dimensional air mass flow rate through the machine and for the non-dimensional resistive torque. It was found that the corresponding relationships between the peripheral Reynolds number and local Nusselt numbers on the generator surfaces and the non-dimensional mass flow rate are linear. However, the dependency of Nusselt number on the non dimensional clearance and the magnet depth is non-linear. For the investigated range of the parameters the following was established: an increase in the peripheral Reynolds number results in higher Nusselt number on both the rotating and stationary surfaces of machines; an increase in the running clearance results in the reduction of the Nusselt number on the machine surfaces; the magnetic segments installed on the surface of the flat rotor act as blades of a radial compressor increasing the air mass flow rate and the corresponding Nusselt number on the stator surface. The combination of the non-dimensional running clearance equal to 9 10-3 and the non-dimensional magnet depth equal to 7.3 10-2 was found to be the one which provides the maximum heat transfer from the stator. This piece of information can be used in the design stage for improving the cooling of AFPM electrical machines without increasing the windage losses and contribute in this way to the enhancement of the overall efficiency of this type of machines

Precision Control of a Sensorless Brushless Direct Current Motor System

Sensorless control strategies were first suggested well over a decade ago with the aim of reducing the size, weight and unit cost of electrically actuated servo systems. The resulting algorithms have been successfully applied to the induction and synchronous motor families in applications where control of armature speeds above approximately one hundred revolutions per minute is desired. However, sensorless position control remains problematic. This thesis provides an in depth investigation into sensorless motor control strategies for high precision motion control applications. Specifically, methods of achieving control of position and very low speed thresholds are investigated. The developed grey box identification techniques are shown to perform better than their traditional white or black box counterparts. Further, fuzzy model based sliding mode control is implemented and results demonstrate its improved robustness to certain classes of disturbance. Attempts to reject uncertainty within the developed models using the sliding mode are discussed. Novel controllers, which enhance the performance of the sliding mode are presented. Finally, algorithms that achieve control without a primary feedback sensor are successfully demonstrated. Sensorless position control is achieved with resolutions equivalent to those of existing stepper motor technology. The successful control of armature speeds below sixty revolutions per minute is achieved and problems typically associated with motor starting are circumvented.Research Instruments Ltd

Design Optimization of Permanent Magnet Machines Over a Target Operating Cycle Using Computationally Efficient Techniques

The common practices of large-scale finite element (FE) model-based design optimization of permanent magnet synchronous machines (PMSMs) oftentimes aim at improving the machine performance at the rated operating conditions, thus overlooking the performance treatment over the entire range of operation in the constant torque and extended speed regions. This is mainly due to the computational complexities associated with several aspects of such large-scale design optimization problems, including the FE-based modeling techniques, large number of load operating points for load-cycle evaluation of the design candidates, and large number of function evaluations required for identification of the globally optimal design solutions. In this dissertation, the necessity of accommodating the entire range of operation in the design optimization of PMSMs is demonstrated through joint application of numerical techniques and mathematical or statistical analyses. For this purpose, concepts such as FE analysis (FEA), design of experiments (DOE), sensitivity analysis, response surface methodology (RSM), and regression analysis are extensively used throughout this work to unscramble the correlations between various factors influencing the design of PMSMs. Also in this dissertation, computationally efficient methodologies are developed and employed to render unprohibitive the problems associated with large-scale design optimization of PMSMs over the entire range of operation of such machines. These include upgrading an existing computationally efficient FEA to solve the electromagnetic field problem at any load operating point residing anywhere in the torque-speed plane, developing a new stochastic search algorithm for effectively handling the constrained optimization problem (COP) of design of electric machines so as to reduce the number of function evaluations required for identifying the global optimum, implementing a k-means clustering algorithm for efficient modeling of the motor load profile, and devising alternative computationally efficient techniques for calculation of strand eddy current losses or characterization of the mechanical stress due to the centrifugal forces on the rotor bridges. The developed methodologies in this dissertation are applicable to the wide class of sine-wave driven PM and synchronous reluctance machines. Here, they were successfully utilized for optimization of two existing propulsion traction motors over predefined operating cycles. Particularly, the well-established benchmark design provided by the Toyota Prius Gen. 2 V-type interior PM (IPM) motor, and a challenging high power density spoke-type IPM for a formula E racing car are treated

Advances in Rotating Electric Machines

It is difficult to imagine a modern society without rotating electric machines. Their use has been increasing not only in the traditional fields of application but also in more contemporary fields, including renewable energy conversion systems, electric aircraft, aerospace, electric vehicles, unmanned propulsion systems, robotics, etc. This has contributed to advances in the materials, design methodologies, modeling tools, and manufacturing processes of current electric machines, which are characterized by high compactness, low weight, high power density, high torque density, and high reliability. On the other hand, the growing use of electric machines and drives in more critical applications has pushed forward the research in the area of condition monitoring and fault tolerance, leading to the development of more reliable diagnostic techniques and more fault-tolerant machines. This book presents and disseminates the most recent advances related to the theory, design, modeling, application, control, and condition monitoring of all types of rotating electric machines

Electric Power Systems and Components for Electric Aircraft

Electric aircraft have gained increasing attention in recent years due to their potential for environmental and economic benefits over conventional airplanes. In order to offer competitive flight times and payload capabilities, electric aircraft power systems (EAPS) must exhibit extremely high efficiencies and power densities. While advancements in enabling technologies have progressed the development of high performance EAPS, further research is required. One challenge in the design of EAPS is determining the best topology to be employed. This work proposes a new graph theory based method for the optimal design of EAPS. This method takes into account data surveyed from a large set of references on commonly seen components including electric machines, power electronics and jet engines. Thousands of design candidates are analyzed based on performance metrics such as end-to-end system efficiency, overall mass, and survivability. It is also shown that sensitivity analysis may be used to systematically evaluate the impact of components and their parameters on various aspects of the architecture design. Once an EAPS architecture has been selected, further, detailed, validation of the power system is required. In these EAPS, many subsystems exist with timescales varying from minutes to hours when considering the aerodynamics, to nanosecond dynamics in the power electronics. This dissertation presents a multiphysics co-simulation framework for the evaluation of EAPS with a unique decoupling method to reduce simulation time without sacrificing detail. The framework has been exemplified on a case study of a 500kW all-electric aircraft, including models for aerodynamics, energy storage, electric motors and power electronics. Electric machines for aviation propulsion must meet several performance requirements, including a constant power speed range (CPSR) of approximately thirty percent above rated speed. This operation is traditionally achieved through the flux weakening technique with an injection of negative d-axis current. However, the degree of CPSR achievable through flux weakening is a strong function of the back emf and d-axis inductance. This dissertation reviews alternative methods for CPSR operation in machines with low inductance. A new method of current weakening has been proposed to address this challenge, involving reducing the machine\u27s current inversely proportional to the operating speed, maintaining constant power through the extended speed range. One benefit of the proposed method is that all current is maintained in the q-axis, maintaining maximum torque per ampere operation. Coreless axial flux permanent magnet (AFPM) machines have recently gained significant attention due to their specific form factor, potentially higher power density and lower losses. Coreless machine designs promise high efficiency particularly at higher speeds, due to the absence of a ferromagnetic core. In this dissertation, coreless AFPM machines with PCB stators are investigated as candidates for propulsion in electric aircraft applications. Two PCB stator design variations are presented with both simulation and experimental results

Model-based powertrain design and control system development for the ideal all-wheel drive electric vehicle

The transfer case based all-wheel drive electric vehicle (TCAWDEV) and dual-axle AWDEV have been investigated to balance concerns about energy consumption, drivability and stability of vehicles. However, the mentioned powertrain architectures have the torque windup issue or the wheel skidding issue. The torque windup is an inherent issue of mechanical linked all-wheel drive systems. The hydraulic motor-based or the electric motor-based ideal all-wheel drive powertrain can provide feasible solutions to the mentioned issues. An ideal AWDEV (IAWDEV) powertrain architecture and its control schemes were proposed by this research; the architecture has four independent driving motors in powertrain. The IAWDEV gives more control freedoms to implement active torque controls and traction mode controls. In essence, this research came up with the distributed powertrain concept, and developed control schemes of the distributed powertrain to replace the transfer case and differential devices. The study investigated the dual-loop motor control, the hybrid sliding mode control (HSMC) and the neural network predictive control to reduce energy consumption and achieve better drivability and stability by optimizing the torque allocation of each dependent wheel. The mentioned control schemes were respectively developed for the anti-slip, differential and yaw stability functionalities of the IAWDEV powertrain. This study also investigated the sizing method that the battery capacity was estimated by using cruise performance at 3% road grade. In addition, the model-based verification was employed to evaluate the proposed powertrain design and control schemes. The verification shows that the design and controls can fulfill drivability requirements and minimize the existing issues, including torque windup and chattering of the slipping wheel. In addition, the verification shows that the IAWDEV can harvest around two times more energy while the vehicle is running on slippery roads than the TCAWDEV and the dual-axle AWDEV; the traction control can achieve better drivability and lower energy consumption than mentioned powertrains; the mode control can reduce 3% of battery charge depleting during the highway driving test. It also provides compelling evidences that the functionalities achieved by complicated and costly mechanical devices can be carried out by control schemes of the IAWDEV; the active torque controls can solve the inherent issues of mechanical linked powertrains; the sizing method is credible to estimate the operation envelop of powertrain components, even though there is some controllable over-sizing

High speed electrical power takeoff for oscillating water columns

This thesis describes research into electrical power takeoff mechanisms for Oscillating Water Column (OWC) wave energy devices. The OWC application is studied and possible alternatives to the existing Induction Generator (IG) are identified. The Permanent Magnet Generator (PMG) is found to be the most promising. Results showed that the IG could almost match the output of the PMG if it could be operated significantly above its rated capacity. This improvement would require only limited changes to the overall OWC system. The ability to operate overloaded is determined by the losses and cooling of the IG. The losses in a suitable IG were measured in tests at Nottingham University. Steady state measurements were made of the cooling ability of the OWC airflow at the LIMPET wave power plant operated by Wavegen (the sponsor company) on Islay. Thermal modelling combining the loss and cooling measurements allowed the maximum capacity of the induction generator in an OWC to be found. A simplified model that accurately represents this system is proposed for use in system design and generator control