CMOS Variable Gain Low Noise Amplifier for Radio Frequency Applications

The evolution of wireless telecommunication systems is expanding in an unprecedented way and such developments have prompted many design challenges specifically for low cost and low power System-on-Chip (SoC). In order to fulfill these needs, the design challenges need to be seen from all levels of the wireless system design from architecture, circuit and the process technology. The first stage of a receiver is the radio frequency (RF) input with low noise amplifier (LNA) as the first building block. Hence, it dominates the performance of the receiver system especially in noise and sensitivity. An LNA which incorporates a variable gain stage is useful in the receiver system in order to achieve continuous gain controllability which can be used to prevent saturation in the receiver when the input signal becomes relatively large compared to the power supply. Thus, circuit solutions of current mirror, gain control loop, capacitively coupled scheme and parallel inter-stage resonance are proposed. On-chip inductors are needed in a LNA to fulfill its requirements of noise and input matching. Therefore, spiral inductors are designed, analyzed and implemented according to the specifications. The main key part of this thesis describes the designs of the variable gain LNA (VGLNA) for low power consumption, continuous gain control and high selectivity over a wide frequency band with the target applications of frequency band at 2.0, 2.4, 5.0, 5.7 and 8 GHz. The VGLNA utilizes current mirror which allows precise copying of the current independent of temperature. With an adequate biased voltage applied, continuous gain control of approximately 28 dB is achieved at low current without degrading the noise performance of the VGLNA significantly, maintaining it below 2 dB. Second approach proposes the capacitively coupled LNA which ensures that the minimum required voltage supply for this topology is only one threshold voltage and not doubled the amount though it is a cascode transistors structure. Hence with these two innovative approaches, the power dissipation of the LNA would be minimal. Continuous gain control is achieved with the gain control loop and current mirror methods. By introducing a simple gain control loop composed of a gain control transistor and a capacitor, a wide continuous gain tuning range is achieved and with the current mirror, the VGLNA has continuous controllability of the gain. A new circuit structure named parallel inter-stage resonance LNA is proposed and it offers high selectivity of gain over the 5 GHz frequency band while keeping the noise figure below 2 dB. The simulation results meet the desired specifications and the measurement results of transistors and inductors are shown to be comparable with the analytical results. Finally, it can be concluded that the VGLNA designs have shown continuous controllable gain and low noise with low power consumption, not forgetting high selectivity over a wide frequency band

Low-power CMOS front-ends for wireless personal area networks

The potential of implementing subthreshold radio frequency circuits in deep sub-micron CMOS technology was investigated for developing low-power front-ends for wireless personal area network (WPAN) applications. It was found that the higher transconductance to bias current ratio in weak inversion could be exploited in developing low-power wireless front-ends, if circuit techniques are employed to mitigate the higher device noise in subthreshold region. The first fully integrated subthreshold low noise amplifier was demonstrated in the GHz frequency range requiring only 260 μW of power consumption. Novel subthreshold variable gain stages and down-conversion mixers were developed. A 2.4 GHz receiver, consuming 540 μW of power, was implemented using a new subthreshold mixer by replacing the conventional active low noise amplifier by a series-resonant passive network that provides both input matching and voltage amplification. The first fully monolithic subthreshold CMOS receiver was also implemented with integrated subthreshold quadrature LO (Local Oscillator) chain for 2.4 GHz WPAN applications. Subthreshold operation, passive voltage amplification, and various low-power circuit techniques such as current reuse, stacking, and differential cross coupling were combined to lower the total power consumption to 2.6 mW. Extremely compact resistive feedback CMOS low noise amplifiers were presented as a cost-effective alternative to narrow band LNAs using high-Q inductors. Techniques to improve linearity and reduce power consumption were presented. The combination of high linearity, low noise figure, high broadband gain, extremely small die area and low power consumption made the proposed LNA architecture a compelling choice for many wireless applications.Ph.D.Committee Chair: Laskar, Joy; Committee Member: Chakraborty, Sudipto; Committee Member: Chang, Jae Joon; Committee Member: Divan, Deepakraj; Committee Member: Kornegay, Kevin; Committee Member: Tentzeris, Emmanoui

Generating All Two-MOS-Transistor Amplifiers Leads to New Wide-Band LNAs

This paper presents a methodology that systematically generates all 2-MOS-transistor wide-band amplifiers, assuming that MOSFET is exploited as a voltage-controlled current source. This leads to new circuits. Their gain and noise factor have been compared to well-known wide-band amplifiers. One of the new circuits appears to have a relatively low noise factor, which is also gain independent. Based on this new circuit, a 50-900 MHz variable-gain wide-band LNA has been designed in 0.35-µm CMOS. Measurements show a noise figure between 4.3 and 4.9 dB for gains from 6 to 11 dB. These values are more than 2 dB lower than the noise figure of the wide-band common-gate LNA for the same input matching, power consumption, and voltage gain. IIP2 and IIP3 are better than 23.5 and 14.5 dBm, respectively, while the LNA drains only 1.5 mA at 3.3 V

Tunable Balun Low-Noise Amplifier in 65nm CMOS Technology

The presented paper includes the design and implementation of a 65 nm CMOS low-noise amplifier (LNA) based on inductive source degeneration. The amplifier is realized with an active balun enabling a single-ended input which is an important requirement for low-cost system on chip implementations. The LNA has a tunable bandpass characteristics from 4.7 GHz up to 5.6 GHz and a continuously tunable gain from 22 dB down to 0 dB, which enables the required flexibility for multi-standard, multi-band receiver architectures. The gain and band tuning is realized with an optimized tunable active resistor in parallel to a tunable L-C tank amplifier load. The amplifier achieves an IIP3 linearity of -8dBm and a noise figure of 2.7 dB at the highest gain and frequency setting with a low power consumption of 10 mW. The high flexibility of the proposed LNA structure together with the overall good performance makes it well suited for future multi-standard low-cost receiver front-ends

CMOS design of chaotic oscillators using state variables: a monolithic Chua's circuit

This paper presents design considerations for monolithic implementation of piecewise-linear (PWL) dynamic systems in CMOS technology. Starting from a review of available CMOS circuit primitives and their respective merits and drawbacks, the paper proposes a synthesis approach for PWL dynamic systems, based on state-variable methods, and identifies the associated analog operators. The GmC approach, combining quasi-linear VCCS's, PWL VCCS's, and capacitors is then explored regarding the implementation of these operators. CMOS basic building blocks for the realization of the quasi-linear VCCS's and PWL VCCS's are presented and applied to design a Chua's circuit IC. The influence of GmC parasitics on the performance of dynamic PWL systems is illustrated through this example. Measured chaotic attractors from a Chua's circuit prototype are given. The prototype has been fabricated in a 2.4- mu m double-poly n-well CMOS technology, and occupies 0.35 mm/sup 2/, with a power consumption of 1.6 mW for a +or-2.5-V symmetric supply. Measurements show bifurcation toward a double-scroll Chua's attractor by changing a bias current

A 14-mW PLL-less receiver in 0.18-μm CMOS for Chinese electronic toll collection standard

This is the accepted manuscript version of the following article: Xiaofeng He, et al., “A 14-mW PLL-less receiver in 0.18-μm CMOS for Chinese electronic toll collection standard”, IEEE Transactions on Circuits and Systems II: Express Briefs, Vol. 61(10): 763-767, August 2014. The final published version is available at: http://ieeexplore.ieee.org/document/6871304/ © 2014 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works.The design of a 14-mW receiver without phase-locked loop for the Chinese electronic toll collection (ETC) system in a standard 0.18-μm CMOS process is presented in this brief. Since the previously published work was mainly based on vehicle-powered systems, low power consumption was not the primary goal of such a system. In contrast, the presented system is designed for a battery-powered system. Utilizing the presented receiver architecture, the entire receiver only consumes 7.8 mA, at the supply voltage of 1.8 V, which indicates a power saving of at least 38% compared with other state-of-the-art designs for the same application. To verify the performance, the bit error rate is measured to be better than 10-6, which well satisfies the Chinese ETC standard. Moreover, the sensitivity of the designed receiver can be readjusted to -50 dBm, which is required by the standard.Peer reviewe

A 1.2 V and 69 mW 60 GHz Multi-channel Tunable CMOS Receiver Design

A multi-channel receiver operating between 56 GHz and 70 GHz for coverage of different 60 GHz bands worldwide is implemented with a 90 nm Complementary Metal-Oxide Semiconductor (CMOS) process. The receiver containing an LNA, a frequency down-conversion mixer and a variable gain amplifier incorporating a band-pass filter is designed and implemented. This integrated receiver is tested at four channels of centre frequencies 58.3 GHz, 60.5 GHz, 62.6 GHz and 64.8 GHz, employing a frequency plan of an 8 GHz-intermediate frequency (IF). The achieved conversion gain by coarse gain control is between 4.8 dB–54.9 dB. The millimeter-wave receiver circuit is biased with a 1.2V supply voltage. The measured power consumption is 69 mW

An Ultra-Low-Power Front-End Neural Interface with Automatic Gain for Uncalibrated Monitoring

Accepted versio

Fully integrated millimeter-wave CMOS phased arrays

A decade ago, RF CMOS, even at low gigahertz frequencies, was considered an oxymoron by all but the most ambitious and optimistic. Today, it is a dominating force in most commercial wireless applications (e.g., cellular, WLAN, GPS, BlueTooth, etc.) and has proliferated into areas such as watt level power amplifiers (PA) [1] that have been the undisputed realm of compound semiconductors. This seemingly ubiquitous embracement of silicon and particularly CMOS is no accident. It stems from the reliable nature of silicon process technologies that make it possible to integrated hundreds of millions of transistors on a single chip without a single device failure, as evident in today’s microprocessors. Applied to microwave and millimeter wave applications, silicon opens the door for a plethora of new topologies, architectures, and applications. This rapid adoption of silicon is further facilitated by one’s ability to integrate a great deal of in situ digital signal processing and calibration [2]. Integration of high-frequency phased-array systems in silicon (e.g., CMOS) promises a future of low-cost radar and gigabit-per-second wireless communication networks. In communication applications, phased array provides an improved signal-to-noise ratio via formation of a beam and reduced interference generation for other users. The practically unlimited number of active and passive devices available on a silicon chip and their extremely tight control and excellent repeatability enable new architectures (e.g., [3]) that are not practical in compound semiconductor module-based approaches. The feasibility of such approaches can be seen through the discussion of an integrated 24GHz 4-element phased-array transmitter in 0.18μm CMOS [2], capable of beam forming and rapid beam steering for radar applications. On-chip power amplifiers (PA), with integrated 50Ω output matching, make this a fully-integrated transmitter. This CMOS transmitter and the 8-element phased-array SiGe receiver in [5], demonstrate the feasibility of 24GHz phased-array systems in silicon-based processes