A 24-GHz SiGe Phased-Array Receiver—LO Phase-Shifting Approach

A local-oscillator phase-shifting approach is introduced to implement a fully integrated 24-GHz phased-array receiver using an SiGe technology. Sixteen phases of the local oscillator are generated in one oscillator core, resulting in a raw beam-forming accuracy of 4 bits. These phases are distributed to all eight receiving paths of the array by a symmetric network. The appropriate phase for each path is selected using high-frequency analog multiplexers. The raw beam-steering resolution of the array is better than 10 [degrees] for a forward-looking angle, while the array spatial selectivity, without any amplitude correction, is better than 20 dB. The overall gain of the array is 61 dB, while the array improves the input signal-to-noise ratio by 9 dB

A 90 nm CMOS 16 Gb/s Transceiver for Optical Interconnects

Interconnect architectures which leverage high-bandwidth optical channels offer a promising solution to address the increasing chip-to-chip I/O bandwidth demands. This paper describes a dense, high-speed, and low-power CMOS optical interconnect transceiver architecture. Vertical-cavity surface-emitting laser (VCSEL) data rate is extended for a given average current and corresponding reliability level with a four-tap current summing FIR transmitter. A low-voltage integrating and double-sampling optical receiver front-end provides adequate sensitivity in a power efficient manner by avoiding linear high-gain elements common in conventional transimpedance-amplifier (TIA) receivers. Clock recovery is performed with a dual-loop architecture which employs baud-rate phase detection and feedback interpolation to achieve reduced power consumption, while high-precision phase spacing is ensured at both the transmitter and receiver through adjustable delay clock buffers. A prototype chip fabricated in 1 V 90 nm CMOS achieves 16 Gb/s operation while consuming 129 mW and occupying 0.105 mm^2

Time-to-digital converters and histogram builders in SPAD arrays for pulsed-LiDAR

Light Detection and Ranging (LiDAR) is a 3D imaging technique widely used in many applications such as augmented reality, automotive, machine vision, spacecraft navigation and landing. Pulsed-LiDAR is one of the most diffused LiDAR techniques which relies on the measurement of the round-trip travel time of an optical pulse back-scattered from a distant target. Besides the light source and the detector, Time-to-Digital Converters (TDCs) are fundamental components in pulsed-LiDAR systems, since they allow to measure the back-scattered photon arrival times and their performance directly impact on LiDAR system requirements (i.e., range, precision, and measurements rate). In this work, we present a review of recent TDC architectures suitable to be integrated in SPAD-based CMOS arrays and a review of data processing solutions to derive the TOF information. Furthermore, main TDC parameters and processing techniques are described and analyzed considering pulsed-LiDAR requirements

5-Bit Dual-Slope Analog-to-Digital Converter-Based Time-to-Digital Converter Chip Design in CMOS Technology

Time-to-Digital Converters (TDC) have gained increasing importance in modern implementations of mixed-signal, data-acquisition and processing interfaces and are used to perform high precision time intervals in systems that incorporate Time-of-Flight (ToF) or Time-of-Arrival (ToA) measurements. The linearity of TDCs is very crucial since most Digital Signal Processing (DSP) systems require very linear inputs to achieve high accuracy. In this work, a TDC has been designed in the 0.5 μm n-well CMOS process that can be used for on-chip integration and in applications requiring high linearity. This TDC used a Dual-Slope-ADC-based architecture for the time-to-digital conversion and consists of the following three main sub-circuits: a time-to-voltage conversion part, an integrating part and digital circuitry. The design is operated with ±2.5V supply voltage and the digital circuitry, consisting of two digital counters and an adder, are operated with a clock frequency of 13MHz. The design of the TDC is discussed and simulated and experimental test results and linearity performance of the fabricated TDC are also presented

Novel Systematic Phase Noise Reduction Techniques for Phase Interpolator Clock and Data Recovery

This work focused on high-speed source-synchronous clock and multi-channel data receivers for inter-chip communications. Designs of inter-chip communication are becoming increasingly difficult with the rise in clock rates and the reduction in voltage supplies. Data transmissions at rates of gigabits per second require a fast and accurate clock and data recovery system on the front end of receivers. Many designs allow for source-synchronous clocking architectures, but this work focused on a dual-loop with a phase-locked loop for frequency tracking and phase integrators for tracking each individual data lane. Limitations with the phase interpolator architecture cause systematic jitter, reducing the data eye. Various techniques exist that aim to reduce or eliminate this systematic jitter from phase interpolator architectures. A technique based on digital lock detection was developed for this work that eliminates the phase interpolator systematic jitter

Design of high speed folding and interpolating analog-to-digital converter

High-speed and low resolution analog-to-digital converters (ADC) are key elements in the read channel of optical and magnetic data storage systems. The required resolution is about 6-7 bits while the sampling rate and effective resolution bandwidth requirements increase with each generation of storage system. Folding is a technique to reduce the number of comparators used in the flash architecture. By means of an analog preprocessing circuit in folding A/D converters the number of comparators can be reduced significantly. Folding architectures exhibit low power and low latency as well as the ability to run at high sampling rates. Folding ADCs employing interpolation schemes to generate extra folding waveforms are called "Folding and Interpolating ADC" (F&I ADC). The aim of this research is to increase the input bandwidth of high speed conversion, and low latency F&I ADC. Behavioral models are developed to analyze the bandwidth limitation at the architecture level. A front-end sample-and-hold unit is employed to tackle the frequency multiplication problem, which is intrinsic for all F&I ADCs. Current-mode signal processing is adopted to increase the bandwidth of the folding amplifiers and interpolators, which are the bottleneck of the whole system. An operational transconductance amplifier (OTA) based folding amplifier, current mirror-based interpolator, very low impedance fast current comparator are proposed and designed to carry out the current-mode signal processing. A new bit synchronization scheme is proposed to correct the error caused by the delay difference between the coarse and fine channels. A prototype chip was designed and fabricated in 0.35μm CMOS process to verify the ideas. The S/H and F&I ADC prototype is realized in 0.35μm double-poly CMOS process (only one poly is used). Integral nonlinearity (INL) is 1.0 LSB and Differential nonlinearity (DNL) is 0.6 LSB at 110 KHz. The ADC occupies 1.2mm2 active area and dissipates 200mW (excluding 70mW of S/H) from 3.3V supply. At 300MSPS sampling rate, the ADC achieves no less than 6 ENOB with input signal lower than 60MHz. It has the highest input bandwidth of 60MHz reported in the literature for this type of CMOS ADC with similar resolution and sample rate

Fast, area-efficient 32-bit LNS for computer arithmetic operations

PhD ThesisThe logarithmic number system has been proposed as an alternative to floating-point. Multiplication, division and square-root operations are accomplished with fixedpoint arithmetic, but addition and subtraction are considerably more challenging. Recent work has demonstrated that these operations too can be done with similar speed and accuracy to their floating-point equivalents, but the necessary circuitry is complex. In particular, it is dominated by the need for large lookup tables for the storage of a non-linear function. This thesis describes the architectures required to implement a newly design approach for producing fast and area-efficient 32-bit LNS arithmetic unit. The designs are structured based on two different algorithms. At first, a new cotransformation procedure is introduced in the singularity region whilst performing subtractions in which the technique capable to generate less total storage than the cotransformation method in the previous LNS architecture. Secondly, improvement to an existing interpolation process is proposed, that also reduce the total tables to an extent that allows their easy synthesis in logic. Consequently, the total delays in the system can be significantly reduced. According to the comparison analysis with previous best LNS design and floating-point units, it is shown that the new LNS architecture capable to offer significantly better in speed while sustaining its accuracy within floating-point limit. In addition, its implementation is more economical than previous best LNS system and almost equivalent with existing floating-point arithmetic unit.University Malaysia Perlis: Ministry of Higher Education, Malaysia

Advanced digital SAR processing study

A highly programmable, land based, real time synthetic aperture radar (SAR) processor requiring a processed pixel rate of 2.75 MHz or more in a four look system was designed. Variations in range and azimuth compression, number of looks, range swath, range migration and SR mode were specified. Alternative range and azimuth processing algorithms were examined in conjunction with projected integrated circuit, digital architecture, and software technologies. The advaced digital SAR processor (ADSP) employs an FFT convolver algorithm for both range and azimuth processing in a parallel architecture configuration. Algorithm performace comparisons, design system design, implementation tradeoffs and the results of a supporting survey of integrated circuit and digital architecture technologies are reported. Cost tradeoffs and projections with alternate implementation plans are presented