141 research outputs found

    Wide-band mixing DACs with high spectral purity

    Get PDF

    Four-element phased-array beamformers and a self-interference canceling full-duplex transciver in 130-nm SiGe for 5G applications at 26 GHz

    Get PDF
    This thesis is on the design of radio-frequency (RF) integrated front-end circuits for next generation 5G communication systems. The demand for higher data rates and lower latency in 5G networks can only be met using several new technologies including, but not limited to, mm-waves, massive-MIMO, and full-duplex. Use of mm-waves provides more bandwidth that is necessary for high data rates at the cost of increased attenuation in air. Massive-MIMO arrays are required to compensate for this increased path loss by providing beam steering and array gain. Furthermore, full duplex operation is desirable for improved spectrum efficiency and reduced latency. The difficulty of full duplex operation is the self-interference (SI) between transmit (TX) and receive (RX) paths. Conventional methods to suppress this interference utilize either bulky circulators, isolators, couplers or two separate antennas. These methods are not suitable for fully-integrated full-duplex massive-MIMO arrays. This thesis presents circuit and system level solutions to the issues summarized above, in the form of SiGe integrated circuits for 5G applications at 26 GHz. First, a full-duplex RF front-end architecture is proposed that is scalable to massive-MIMO arrays. It is based on blind, RF self-interference cancellation that is applicable to single/shared antenna front-ends. A high resolution RF vector modulator is developed, which is the key building block that empowers the full-duplex frontend architecture by achieving better than state-of-the-art 10-b monotonic phase control. This vector modulator is combined with linear-in-dB variable gain amplifiers and attenuators to realize a precision self-interference cancellation circuitry. Further, adaptive control of this SI canceler is made possible by including an on-chip low-power IQ downconverter. It correlates copies of transmitted and received signals and provides baseband/dc outputs that can be used to adaptively control the SI canceler. The solution comes at the cost of minimal additional circuitry, yet significantly eases linearity requirements of critical receiver blocks at RF/IF such as mixers and ADCs. Second, to complement the proposed full-duplex front-end architecture and to provide a more complete solution, high-performance beamformer ICs with 5-/6- b phase and 3-/4-b amplitude control capabilities are designed. Single-channel, separate transmitter and receiver beamformers are implemented targeting massive- MIMO mode of operation, and their four-channel versions are developed for phasedarray communication systems. Better than state-of-the-art noise performance is obtained in the RX beamformer channel, with a full-channel noise figure of 3.3 d

    Low Power CMOS Interface Circuitry for Sensors and Actuators

    Get PDF

    Design Considerations for Wide Bandwidth Continuous-Time Low-Pass Delta-Sigma Analog-to-Digital Converters

    Get PDF
    Continuous-time (CT) delta-sigma (ΔΣ) analog-to-digital converters (ADC) have emerged as the popular choice to achieve high resolution and large bandwidth due to their low cost, power efficiency, inherent anti-alias filtering and digital post processing capabilities. This work presents a detailed system-level design methodology for a low-power CT ΔΣ ADC. Design considerations and trade-offs at the system-level are presented. A novel technique to reduce the sensitivity of the proposed ADC to clock jitter-induced feedback charge variations by employing a hybrid digital-to-analog converter (DAC) based on switched-capacitor circuits is also presented. The proposed technique provides a clock jitter tolerance of up to 5ps (rms). The system is implemented using a 5th order active-RC loop filter, 9-level quantizer and DAC, achieving 74dB SNDR over 20MHz signal bandwidth, at 400MHz sampling frequency in a 1.2V, 90 nm CMOS technology. A novel technique to improve the linearity of the feedback digital-to-analog converters (DAC) in a target 11-bits resolution, 100MHz bandwidth, 2GHz sampling frequency CT ΔΣ ADC is also presented in this work. DAC linearity is improved by combining dynamic element matching and automatic background calibration to achieve up to 18dB improvement in the SNR. Transistor-level circuit implementation of the proposed technique was done in a 1.8V, 0.18μm BiCMOS process

    High-speed Design Of High-resolution Dacs

    Get PDF
    Tez (Doktora) -- İstanbul Teknik Üniversitesi, Fen Bilimleri Enstitüsü, 2009Thesis (PhD) -- İstanbul Technical University, Institute of Science and Technology, 2009Bu çalışmada, yüksek çözünürlüklü akım yönlendirmeli sayısal-analog dönüştürücülerin (SAD) hızlı tasarımını sağlayan yöntemler incelenmekte ve yeni yaklaşımlar önerilmektedir. Veri dönüştürücüler analog ve sayısal dünyalar arasında bir köprü oluşturdukları için hızlı ve verimli bir şekilde gerçekleştirilmeleri yüksek derecede arzu edilmektedir. Yüksek hızlı (birkaç 100MHz) ve yüksek çözünürlüklü (10 bitten fazla) SAD için artan rağbet, akım yönlendirmeli SADların kullanımını zorunlu kılmaktadır. Yüksek performanslı akım yönlendirmeli SADların tasarımında ve gerçekleştirmesinde kesimleme (segmentation) yöntemi kullanılmaktadır. Bu yöntem, yüksek hız ve yüksek çözünürlük gerektiren uygulamaların çoğunda avantajlı olmasına rağmen uzun süreli tasarım zamanı, karmaşıklık ve yüksek maliyet yüzünden değer kaybetmektedir. Böylece, bazı uygulamalar için zaman ve maliyet açısından bu yöntemin kullanılması hızlı ve verimli olmayabilir. Bu problemlerin üstesinden gelmek için yüksek çözünürlüklü SADların yüksek hızlı tasarımını sağlayan hızlı ve verimli yöntemler dikkate alınmaktadır. Uygun bir tasarım yöntemi ve yeni bir yapı önerilmektedir. Akım yönlendirmeli SADlar gibi karmaşık karma yapılı sistemlerin tasarımı için davranışsal modelin oluşturulması zorunlu olmaktadır. Bu amaçla gerçekleştirilen modellerin çoğu sistemin davranışı hakkında istenilen eksiksiz manzarayı vermemektedir. Bu yüzden, transistor seviyesindeki tasarıma geçmeden önce, tasarımı hızlandırabilen ve sistemin davranışını doğru bir şekilde yansıtabilen modeller geliştirilmektedir. SIMULINK® kullanılarak bir davranışsal model kurulmakta ve modelin performansı benzetimlerle sınanmaktadır. Sonuç olarak, uygulanan yöntemin verimliliğini ve davranışsal modelin doğruluğunu sınamak için 0.35µm CMOS proses teknolojisi için tasarlanan bir 12 bitlik melez akım yönlendirmeli SAD kullanılmaktadır. Yapı bloklarında yapılan iyileştirmeler ve kullanılan farklı yöntemler, gerçekleştirilen SAD’ın serimindeki ilgili kısımlarda yer almaktadırlar. CADENCE Geleneksel Tümleşik Devre Tasarım Araçları kullanılarak serim sonrası benzetimleri yapılmakta ve SAD’ın performans karakteristikleri incelenmektedir.In this thesis, different problems related to the design speed-up of high-resolution current-steering digital-to-analog converters (DAC) are addressed and novel solutions are proposed. Since data converters form the bridge between the analog and digital world their efficient implementation is highly desirable. The increase in demand for high-speed (several 100MHz) and high-resolution (higher than 10-bit) DAC, forces the use of current-steering DACs. Segmentation method is used for the design and the implementation of high performance current-steering DACs. Although this methodology is advantageous in most of the applications requiring high-speed and high-resolution, it suffers from the prolonged design time, complexity and high cost. Thus, the use of this methodology for some applications is not efficient concerning the time and the cost. To overcome these problems efficient methodologies for the high-speed design of high-resolution DACs are considered. A proper design methodology and a novel architecture are introduced. Behavioral modeling is necessary for the design of complex mixed-mode systems like current-steering DACs. Most of the models constructed can not give a complete view of the system’s behavior. For this reason, models that speed up the design and reflect accurately the behavior of the system prior to transistor level implementation are developed. A SIMULINK® based behavioral model is developed and verified through simulations. To conclude, the efficiency of the applied methodology and the accuracy of the behavioral model are validated through the implementation of a 12-bit hybrid current-steering DAC in a 0.35µm CMOS process technology. The improvements in the building blocks and the different approaches used are reflected in the respective parts of the layout of the implemented DAC. Post-layout simulations are obtained using CADENCE Custom IC Design Tools and the performance metrics of the DAC are investigated.DoktoraPh

    Digitally Interfaced Analog Correlation Filter System for Object Tracking Applications

    Get PDF
    Advanced correlation filters have been employed in a wide variety of image processing and pattern recognition applications such as automatic target recognition and biometric recognition. Among those, object recognition and tracking have received more attention recently due to their wide range of applications such as autonomous cars, automated surveillance, human-computer interaction, and vehicle navigation.Although digital signal processing has long been used to realize such computational systems, they consume extensive silicon area and power. In fact, computational tasks that require low to moderate signal-to-noise ratios are more efficiently realized in analog than digital. However, analog signal processing has its own caveats. Mainly, noise and offset accumulation which degrades the accuracy, and lack of a scalable and standard input/output interface capable of managing a large number of analog data.Two digitally-interfaced analog correlation filter systems are proposed. While digital interfacing provided a standard and scalable way of communication with pre- and post-processing blocks without undermining the energy efficiency of the system, the multiply-accumulate operations were performed in analog. Moreover, non-volatile floating-gate memories are utilized as storage for coefficients. The proposed systems incorporate techniques to reduce the effects of analog circuit imperfections.The first system implements a 24x57 Gilbert-multiplier-based correlation filter. The I/O interface is implemented with low-power D/A and A/D converters and a correlated double sampling technique is implemented to reduce offset and lowfrequency noise at the output of analog array. The prototype chip occupies an area of 3.23mm2 and demonstrates a 25.2pJ/MAC energy-efficiency at 11.3 kVec/s and 3.2% RMSE.The second system realizes a 24x41 PWM-based correlation filter. Benefiting from a time-domain approach to multiplication, this system eliminates the need for explicit D/A and A/D converters. Careful utilization of clock and available hardware resources in the digital I/O interface, along with application of power management techniques has significantly reduced the circuit complexity and energy consumption of the system. Additionally, programmable transconductance amplifiers are incorporated at the output of the analog array for offset and gain error calibration. The prototype system occupies an area of 0.98mm2 and is expected to achieve an outstanding energy-efficiency of 3.6pJ/MAC at 319kVec/s with 0.28% RMSE

    High-Speed Delta-Sigma Data Converters for Next-Generation Wireless Communication

    Get PDF
    In recent years, Continuous-time Delta-Sigma(CT-ΔΣ) analog-to-digital converters (ADCs) have been extensively investigated for their use in wireless receivers to achieve conversion bandwidths greater than 15 MHz and higher resolution of 10 to 14 bits. This dissertation investigates the current state-of-the-art high-speed single-bit and multi-bit Continuous-time Delta-Sigma modulator (CT-ΔΣM) designs and their limitations due to circuit non-idealities in achieving the performance required for next-generation wireless standards. Also, we presented complete architectural and circuit details of a high-speed single-bit and multi-bit CT-ΔΣM operating at a sampling rate of 1.25 GSps and 640 MSps respectively (the highest reported sampling rate in a 0.13 μm CMOS technology node) with measurement results. Further, we propose novel hybrid ΔΣ architecture with two-step quantizer to alleviate the bandwidth and resolution bottlenecks associated with the contemporary CT-ΔΣM topologies. To facilitate the design with the proposed architecture, a robust systematic design method is introduced to determine the loop-filter coefficients by taking into account the non-ideal integrator response, such as the finite opamp gain and the presence of multiple parasitic poles and zeros. Further, comprehensive system-level simulation is presented to analyze the effect of two-step quantizer non-idealities such as the offset and gain error in the sub-ADCs, and the current mismatch between the MSB and LSB elements in the feedback DAC. The proposed novel architecture is demonstrated by designing a high-speed wideband 4th order CT-ΔΣ modulator prototype, employing a two-step quantizer with 5-bits resolution. The proposed modulator takes advantage of the combination of a high-resolution two-step quantization technique and an excess-loop delay (ELD) compensation of more than one clock cycle to achieve lower-power consumption (28 mW), higher dynamic range (\u3e69 dB) with a wide conversion bandwidth (20 MHz), even at a lower sampling rate of 400 MHz. The proposed modulator achieves a Figure of Merit (FoM) of 340 fJ/level

    Design of low-voltage power efficient frequency dividers in folded MOS current mode logic

    Get PDF
    In this paper we propose a methodology to design high-speed, power-efficient static frequency dividers based on the low-voltage Folded MOS Current Mode Logic (FMCML) approach. A modeling strategy to analyze the dependence of propagation delay and power consumption on the bias currents of the divide-by-2 (DIV2) cell is introduced. We demonstrate that the behavior of the FMCML DIV2 cell is different both from the one of the conventional MCML DFF (D-type Flip-Flop) and from FMCML DFF without a level shifter. Then an analytical strategy to optimize the divider in different design scenarios: maximum speed, minimum power-delay product (PDP) or minimum energy-delay product (EDP) is presented. The possibility to scale the bias currents through the divider stages without affecting the speed performance is also investigated. The proposed analytical approach allows to gain a deep insight into the circuit behavior and to comprehensively optimize the different design tradeoffs. The derived models and design guidelines are validated against transistor level simulations referring to a commercial 28nm FDSOI CMOS process. Different divide-by-8 circuits following different optimization strategies have been designed in the same 28nm CMOS technology showing the effectiveness of the proposed methodology

    Design of a 125 mhz tunable continuous-time bandpass modulator for wireless IF applications

    Get PDF
    Bandpass sigma-delta modulators combine oversampling and noise shaping to get very high resolution in a limited bandwidth. They are widely used in applications that require narrowband high-resolution conversion at high frequencies. In recent years interests have been seen in wireless system and software radio using sigma-delta modulators to digitize signals near the front end of radio receivers. Such applications necessitate clocking the modulators at a high frequency (MHz or above). Therefore a loop filter is required in continuous-time circuits (e.g., using transconductors and integrators) rather than discretetime circuits (e.g., using switched capacitors) where the maximum clocking rate is limited by the bandwidth of Opamp, switchÂs speed and settling-time of the circuitry. In this work, the design of a CMOS fourth-order bandpass sigma-delta modulator clocking at 500 MHz for direct conversion of narrowband signals at 125 MHz is presented. A new calibration scheme is proposed for the best signal-to-noise-distortion-ratio (SNDR) of the modulator. The continuous-time loop filter is based on Gm-C resonators. A novel transconductance amplifier has been developed with high linearity at high frequency. Qfactor of filter is enhanced by tunable negative impedance which cancels the finite output impendence of OTA. The fourth-order modulator is implemented using 0.35 mm triplemetal standard analog CMOS technology. Postlayout simulation in CADENCE demonstrates that the modulator achieves a SNDR of 50 dB (~8 bit) performance over a 1 MHz bandwidth. The modulatorÂs power consumption is 302 mW from supply power of ± 1.65V
    corecore