A mismatch-insensitive high-accuracy high-speed continuous-time current comparator in low voltage CMOS

This paper presents a CMOS current comparator which employs nonlinear feedback to obtain high-accuracy (down to 1.5 pA) and high-speed for low input currents (8 ns@50 nA). This structure is much faster for low currents (below 10 /spl mu/A) than other previous nonlinear feedback comparators. Particularly, when compared to the fastest current comparator reported up to now, the new one operates at more that 100 times faster for a 1 nA current, with smaller area occupation and similar power consumption. In addition, the new comparator is virtually insensitive to mismatch and capable of operating with supply voltages as low as 1 V

Baseband analog front-end and digital back-end for reconfigurable multi-standard terminals

Multimedia applications are driving wireless network operators to add high-speed data services such as Edge (E-GPRS), WCDMA (UMTS) and WLAN (IEEE 802.11a,b,g) to the existing GSM network. This creates the need for multi-mode cellular handsets that support a wide range of communication standards, each with a different RF frequency, signal bandwidth, modulation scheme etc. This in turn generates several design challenges for the analog and digital building blocks of the physical layer. In addition to the above-mentioned protocols, mobile devices often include Bluetooth, GPS, FM-radio and TV services that can work concurrently with data and voice communication. Multi-mode, multi-band, and multi-standard mobile terminals must satisfy all these different requirements. Sharing and/or switching transceiver building blocks in these handsets is mandatory in order to extend battery life and/or reduce cost. Only adaptive circuits that are able to reconfigure themselves within the handover time can meet the design requirements of a single receiver or transmitter covering all the different standards while ensuring seamless inter-interoperability. This paper presents analog and digital base-band circuits that are able to support GSM (with Edge), WCDMA (UMTS), WLAN and Bluetooth using reconfigurable building blocks. The blocks can trade off power consumption for performance on the fly, depending on the standard to be supported and the required QoS (Quality of Service) leve

Digital-to-Analog Converter Interface for Computer Assisted Biologically Inspired Systems

In today\u27s integrated circuit technology, system interfaces play an important role of enabling fast, reliable data communications. A key feature of this work is the exploration and development of ultra-low power data converters. Data converters are present in some form in almost all mixed-signal systems; in particular, digital-to-analog converters present the opportunity for digitally controlled analog signal sources. Such signal sources are used in a variety of applications such as neuromorphic systems and analog signal processing. Multi-dimensional systems, such as biologically inspired neuromorphic systems, require vectors of analog signals. To use a microprocessor to control these analog systems, we must ultimately convert the digital control signal to an analog control signal and deliver it to the system. Integrating such capabilities of a converter on chip can yield significant power and chip area constraints. Special attention is paid to the power efficiency of the data converter, the data converter design discussed in this thesis yields the lowest power consumption to date. The need for a converter with these properties leads us to the concept of a scalable array of power-efficient digital-to-analog converters; the channels of which are time-domain multiplexed so that chip-area is minimized while preserving performance. To take further advantage of microprocessor capabilities, an analog-to- digital design is proposed to return the analog system\u27s outputs to the microprocessor in a digital form. A current-steering digital-to-analog converter was chosen as a candidate for the conversion process because of its natural speed and voltage-to-current translation properties. This choice is nevertheless unusual, because current-steering digital- to-analog converters have a reputation for high performance with high power consumption. A time domain multiplexing scheme is presented such that a digital data set of any size is synchronously multiplexed through a finite array of converters, minimizing the total area and power consumption. I demonstrate the suitability of current-steering digital-to-analog converters for ultra low-power operation with a proof-of-concept design in a widely available 130 nm CMOS technology. In statistical simulation, the proposed digital-to-analog converter was capable of 8-bit, 100 kSps operation while consuming 231 nW of power from a 1 V supply

Iddq testing of a CMOS 10-bit charge scaling digital-to-analog converter

This work presents an effective built-in current sensor (BICS), which has a very small impact on the performance of the circuit under test (CUT). The proposed BICS works in two-modes the normal mode and the test mode. In the normal mode the BICS is isolated from the CUT due to which there is no performance degradation of the CUT. In the testing mode, our BICS detects the abnormal current caused by permanent manufacturing defects. Further more our BICS can also distinguish the type of defect induced (Gate-source short, source-drain short and drain-gate short). Our BICS requires neither an external voltage source nor current source. Hence the BICS requires less area and is more efficient than the conventional current sensors. The circuit under test is a 10-bit digital to analog converter using charge-scaling architecture

Analysis and equalization of data-dependent jitter

Data-dependent jitter limits the bit-error rate (BER) performance of broadband communication systems and aggravates synchronization in phase- and delay-locked loops used for data recovery. A method for calculating the data-dependent jitter in broadband systems from the pulse response is discussed. The impact of jitter on conventional clock and data recovery circuits is studied in the time and frequency domain. The deterministic nature of data-dependent jitter suggests equalization techniques suitable for high-speed circuits. Two equalizer circuit implementations are presented. The first is a SiGe clock and data recovery circuit modified to incorporate a deterministic jitter equalizer. This circuit demonstrates the reduction of jitter in the recovered clock. The second circuit is a MOS implementation of a jitter equalizer with independent control of the rising and falling edge timing. This equalizer demonstrates improvement of the timing margins that achieve 10/sup -12/ BER from 30 to 52 ps at 10 Gb/s