High Efficiency Cross-Coupled Charge Pump Circuit with Four-Clock Signals

© Allerton Press, Inc. 2018A fully integrated cross-coupled charge pump circuit for boosting dc-to-dc converter applications with four-clock signals has been proposed. With the new clock scheme, this charge pump eliminates all of the reversion power loss and reduces the ripple voltage. In addition, the largest voltage differences between the terminals of all transistors do not exceed the power supply voltage for solving the gate-oxide overstress problem in the conventional charge pump circuits and enhancing the reliability. This proposed charge pump circuit does not require any extra level shifter; therefore, the power efficiency is increased. The proposed charge pump circuit has been simulated using Spectre in the TSMC 0.18 μm CMOS process. The simulation results show that the maximum voltage conversion efficiency of the new 3-stage cross-coupled circuit with an input voltage of 1.5Vis 99.8%. According to the comparison results of the conventional pump and the enhanced charge pump proposed, the output ripple voltage has been significantly reduced.Peer reviewe

A robust high-efficiency cross-coupled charge pump circuit without blocking transistors

This document is the Accepted Manuscript version of the following article: Minglin Ma, Xinglong Cai, Yichuang Sun, and Nike George, ‘A robust high-efficiency cross-coupled charge pump circuit without blocking transistors’, Analog Integrated Circuits and Signal Processing, Vol. 95 (3): 395-401, June 2018. Under embargo until 16 March 2019. The final publication is available at Springer via: https://doi.org/10.1007/s10470-018-1149-xA fully integrated cross-coupled charge pump circuit with a new clock scheme has been presented in this paper. The new clock scheme ensures that all NMOS pre-charge transistors are turned off when the voltages of main clock signals are high. Notably, all PMOS transfer transistors will be turned off when the voltages of the main clock signals are low. As a result, the charge pump eliminates all of the reversion power loss and reduces the ripple voltage. The proposed charge pump has a better performance even in scenarios where the main clock signals are mismatched. The proposed charge pump circuit was simulated using spectre in the TSMC 0.18 µm CMOS process. The simulation results show that the proposed charge pump circuit has a high voltage conversion efficiency and low ripple voltage.Peer reviewe

Power management systems based on switched-capacitor DC-DC converter for low-power wearable applications

The highly efficient ultra-low-power management unit is essential in powering low-power wearable electronics. Such devices are powered by a single input source, either by a battery or with the help of a renewable energy source. Thus, there is a demand for an energy conversion unit, in this case, a DC-DC converter, which can perform either step-up or step-down conversions to provide the required voltage at the load. Energy scavenging with a boost converter is an intriguing choice since it removes the necessity of bulky batteries and considerably extends the battery life. Wearable devices are typically powered by a monolithic battery. The commonly available battery such as Alkaline or Lithium-ion, degrade over time due to their life spans as it is limited by the number of charge cycles- which depend highly on the environmental and loading condition. Thus, once it reaches the maximum number of life cycles, the battery needs to be replaced. The operation of the wearable devices is limited by usable duration, which depends on the energy density of the battery. Once the stored energy is depleted, the operation of wearable devices is also affected, and hence it needs to be recharged. The energy harvesters- which gather the available energy from the surroundings, however, have no limitation on operating life. The application can become battery-less given that harvestable energy is sufficiently powering the low-power devices. Although the energy harvester may not completely replace the battery source, it ensures the maximum duration of use and assists to become autonomous and self-sustain devices. The photovoltaic (PV) cell is a promising candidate as a hypothetical input supply source among the energy harvesters due to its smaller area and high power density over other harvesters. Solar energy use PV harvester can convert ambient light energy into electrical energy and keep it in the storage device. The harvested output of PV cannot directly connect to wearable loads for two main reasons. Depending on the incoming light, the harvested current result in varying open-circuit voltage. It requires the power management circuit to deal with unregulated input variation. Second, depending on the PV cell's material type and an effective area, the I-V characteristic's performance varies, resulting in a variation of the output power. There are several works of maximum power point tracking (MPPT) methods that allow the solar energy harvester to achieve optimal harvested power. Therefore, the harvested power depends on the size and usually small area cell is sufficient for micro-watt loads low-powered applications. The available harvested voltage, however, is generally very low-voltage range between 0.4-0.6 V. The voltage ratings of electronics in standard wearable applications operate in 1.8-3 V voltages as described in introduction’s application example section. It is higher than the supply source can offer. The overcome the mismatch voltage between source and supply circuit, a DC-DC boost converter is necessary. The switch-mode converters are favoured over the linear converters due to their highly efficient and small area overhead. The inductive converter in the switch-mode converter is common due to its high-efficiency performance. However, the integration of the inductor in the miniaturised integrated on-chip design tends to be bulky. Therefore, the switched-capacitor approach DC-DC converters will be explored in this research. In the switched-capacitor converter universe, there is plenty of work for single-output designs for various topologies. Most converters are reconfigurable to the different DC voltage levels apart from Dickson and cross-coupled charge pump topologies due to their boosting power stage architecture through a number of stages. However, existing multi-output converters are limited to the fixed gain ratio. This work explores the reconfigurable dual-output converter with adjustable gain to compromise the research gap. The thesis's primary focus is to present the inductor-less, switched-capacitor-based DC-DC converter power management system (PMS) supplied by a varying input of PV energy harvester input source. The PMS should deliver highly efficient regulated voltage conversion ratio (VCR) outputs to low-power wearable electronic devices that constitute multi-function building blocks

Analysis and design of switched-capacitor DC-DC converters with discrete event models

Ph. D. Thesis.Switched-capacitor DC-DC converters (SCDDCs) play a critical role in low power integrated systems. The analysis and design processes of an SCDDC impact the performance and power efficiency of the whole system. Conventionally, researchers carry out the analysis and design processes by viewing SCDDCs as analogue circuits. Analogue attributes of an SCDDC, such as the charge flow current or the equivalent output impedance, have been studied in considerable detail for performance enhancement. However, in most existing work, less attention is paid to the analysis of discrete events (e.g. digital signal transitions) and the relationships between discrete events in SCDDCs. These discrete events and the relationships between discrete events also affect the performance of SCDDCs. Certain negative effects of SCDDCs such as leakage current are introduced by unhealthy discrete states. For example, MOS devices in an SCDDC could conduct undesirably under certain combinations of signals, resulting in reversion losses (a type of leakage in SCDDCs). However, existing work only use verbal reasoning and waveform descriptions when studying these discrete events, which may cause confusion and result in an informal design process consisting of intuitive design and backed up merely by validation based on natural language discussions and simulations. There is therefore a need for formalised methods to describe and analyse these discrete events which may facilitate systematic design techniques. This thesis presents a new method of analysing and designing SCDDCs using discrete event models. Discrete event models such as Petri nets and Signal Transition Graphs (STGs) are commonly used in asynchronous circuits to formally describe and analyse the relationships between discrete transitions. Modelling SCDDCs with discrete event models provides a formal way to describe the relations between discrete transitions in SCDDCs. These discrete event models can be used for analysis, verification and even design guidance for SCDDC design. The rich set of existing analysis methods and tools for discrete event models could be applied to SCDDCs, potentially improving the analysis and design flow for them. Moreover, since Petri nets and STGs are generally used to analyse and design asynchronous circuits, modelling and designing SCDDCs with STG models may additionally facilitate the incorporation of positive features of asynchronous circuits in SCDDCs (e.g. no clock skew). In this thesis, the relations between discrete events in SCDDCs are formally described with SC-STG (an extended STG targeting multi-voltage systems, to which SCDDCs belong), which avoids the potential confusion due to natural language and waveform descriptions. Then the concurrency and causality relations described in SC-STG model are extended to Petri nets, with which the presence of reversion losses can be formally determined and verified. Finally, based on the STG and Petri net models, a new design method for reversion-loss-free SCDDCs is proposed. In SCDDCs designed with the new method, reversion losses are entirely removed by introducing asynchronous controls, synthesised with the help of a software synthesis toolkit “Workcraft”. To demonstrate the analysis capabilities of the method, several cross-coupled voltage doublers (a type of SCDDC) are analysed and studied with discrete event models as examples in this thesis. To demonstrate the design capabilities of the method, a new reversion-loss-free cross-coupled voltage doubler is designed. The cross-coupled voltage doubler is widely used in low power integrated systems such as flash memories, LCD drivers and wireless energy harvesting systems. The proposed modelling method is potentially used in both research and industrial area of those applications for a formal and high-efficiency design proces

Proceedings of the 2018 Canadian Society for Mechanical Engineering (CSME) International Congress

Published proceedings of the 2018 Canadian Society for Mechanical Engineering (CSME) International Congress, hosted by York University, 27-30 May 2018