Bulk-driven flipped voltage follower

A voltage buffer so-called the bulk-driven flipped voltage follower is presented. This proposal is based on the flipped voltage follower (FVF) technique, but a bulk-driven MOSFET with the replica-biased scheme is utilized for the input device to eliminate the DC level shift. The proposed buffer has been designed and simulated with a 0.35 mum CMOS technology. The input current and capacitance of our proposal are 1.5 pA and 9.3 fF respectively, and with 0.8 V peak-to-peak 500 kHz input, the total harmonic distortion is 0.5% for a 10 pF load. This circuit can operate from a single 1.2 V power supply and consumes only 2.5 muA

Design of a ROIC for scanning type HgCdTe LWIR focal plane arrays

Design of a silicon readout integrated circuit (ROIC) for LWIR HgCdTe Focal Plane is presented. ROIC incorporates time delay integration (TDI) functionality over seven elements with a supersampling rate of three, increasing SNR and the spatial resolution. Novelty of this topology is inside TDI stage; integration of charges in TDI stage implemented in current domain by using switched current structures that reduces required area for chip and improves linearity performance. ROIC, in terms of functionality, is capable of bidirectional scan, programmable integration time and 5 gain settings at the input. Programming can be done parallel or serially with digital interface. ROIC can handle up to 3.5V dynamic range with the input stage to be direct injection (DI) type. With the load being 10pF capacitive in parallel with 1MΩ resistance, output settling time is less than 250nsec enabling the clock frequency up to 4MHz. The manufacturing technology is 0.35μm, double poly-Si, four-metal (3 metals and 1 top metal) 5V CMOS process

Class-AB rail-to-rail CMOS buffer with bulk-driven super source followers

This paper describes a rail-to-rail CMOS analog voltage buffer designed to have extremely low static current consumption as well as high current drive capability. The buffer employs a complementary pair of super source followers, but a bulk-driven input device with the replica-biased scheme is utilized to eliminate the DC level shift, quasi-floating gate transistors to achieve class-AB performance, and a current switch which shifts between the complementary pair to allow rail-to-rail operation. The proposed buffer has been designed for a 0.35 mum CMOS technology to operate at a 1.8 V supply voltage. The simulated results are provided to demonstrate that the total harmonic distortion for a 1.6 Vpp 100 kHz sine wave with a 68 pF load is as low as -46 dB, whilst the static current consumption remains under 8 muA

Low Voltage Low Power Analogue Circuits Design

Disertační práce je zaměřena na výzkum nejběžnějších metod, které se využívají při návrhu analogových obvodů s využití nízkonapěťových (LV) a nízkopříkonových (LP) struktur. Tyto LV LP obvody mohou být vytvořeny díky vyspělým technologiím nebo také využitím pokročilých technik návrhu. Disertační práce se zabývá právě pokročilými technikami návrhu, především pak nekonvenčními. Mezi tyto techniky patří využití prvků s řízeným substrátem (bulk-driven - BD), s plovoucím hradlem (floating-gate - FG), s kvazi plovoucím hradlem (quasi-floating-gate - QFG), s řízeným substrátem s plovoucím hradlem (bulk-driven floating-gate - BD-FG) a s řízeným substrátem s kvazi plovoucím hradlem (quasi-floating-gate - BD-QFG). Práce je také orientována na možné způsoby implementace známých a moderních aktivních prvků pracujících v napěťovém, proudovém nebo mix-módu. Mezi tyto prvky lze začlenit zesilovače typu OTA (operational transconductance amplifier), CCII (second generation current conveyor), FB-CCII (fully-differential second generation current conveyor), FB-DDA (fully-balanced differential difference amplifier), VDTA (voltage differencing transconductance amplifier), CC-CDBA (current-controlled current differencing buffered amplifier) a CFOA (current feedback operational amplifier). Za účelem potvrzení funkčnosti a chování výše zmíněných struktur a prvků byly vytvořeny příklady aplikací, které simulují usměrňovací a induktanční vlastnosti diody, dále pak filtry dolní propusti, pásmové propusti a také univerzální filtry. Všechny aktivní prvky a příklady aplikací byly ověřeny pomocí PSpice simulací s využitím parametrů technologie 0,18 m TSMC CMOS. Pro ilustraci přesného a účinného chování struktur je v disertační práci zahrnuto velké množství simulačních výsledků.The dissertation thesis is aiming at examining the most common methods adopted by analog circuits' designers in order to achieve low voltage (LV) low power (LP) configurations. The capability of LV LP operation could be achieved either by developed technologies or by design techniques. The thesis is concentrating upon design techniques, especially the non–conventional ones which are bulk–driven (BD), floating–gate (FG), quasi–floating–gate (QFG), bulk–driven floating–gate (BD–FG) and bulk–driven quasi–floating–gate (BD–QFG) techniques. The thesis also looks at ways of implementing structures of well–known and modern active elements operating in voltage–, current–, and mixed–mode such as operational transconductance amplifier (OTA), second generation current conveyor (CCII), fully–differential second generation current conveyor (FB–CCII), fully–balanced differential difference amplifier (FB–DDA), voltage differencing transconductance amplifier (VDTA), current–controlled current differencing buffered amplifier (CC–CDBA) and current feedback operational amplifier (CFOA). In order to confirm the functionality and behavior of these configurations and elements, they have been utilized in application examples such as diode–less rectifier and inductance simulations, as well as low–pass, band–pass and universal filters. All active elements and application examples have been verified by PSpice simulator using the 0.18 m TSMC CMOS parameters. Sufficient numbers of simulated plots are included in this thesis to illustrate the precise and strong behavior of structures.

Low-Voltage Ultra-Low-Power Current Conveyor Based on Quasi-Floating Gate Transistors

The field of low-voltage low-power CMOS technology has grown rapidly in recent years; it is an essential prerequisite particularly for portable electronic equipment and implantable medical devices due to its influence on battery lifetime. Recently, significant improvements in implementing circuits working in the low-voltage low-power area have been achieved, but circuit designers face severe challenges when trying to improve or even maintain the circuit performance with reduced supply voltage. In this paper, a low-voltage ultra-low-power current conveyor second generation CCII based on quasi-floating gate transistors is presented. The proposed circuit operates at a very low supply voltage of only ±0.4 V with rail-to-rail voltage swing capability and a total quiescent power consumption of mere 9.5 µW. Further, the proposed circuit is not only able to process the AC signal as it's usual at quasi-floating gate transistors but also the DC which extends the applicability of the proposed circuit. In conclusion, an application example of the current-mode quadrature oscillator is presented. PSpice simulation results using the 0.18 µm TSMC CMOS technology are included to confirm the attractive properties of the proposed circuit

A 12b 250 MS/s Pipelined ADC With Virtual Ground Reference Buffers

The virtual ground reference buffer (VGRB) technique is introduced as a means to improve the performance of switched-capacitor circuits. The technique enhances the performance by improving the feedback factor of the op-amp without affecting the signal gain. The bootstrapping action of the level-shifting buffers relaxes key op-amp performance requirements including unity-gain bandwidth, noise, open-loop gain and offset compared with conventional circuits. This reduces the design complexity and the power consumption of op-amp based circuits. Based on this technique, a 12 b pipelined ADC is implemented in 65 nm CMOS that achieves 67.0 dB SNDR at 250 MS/s and consumes 49.7 mW of power from a 1.2 V power supply

Design of a Reference Buffer for a Delta-Sigma ADC with Current DAC

In analog to digital conversion, it’s necessary to provide a reference voltage to the Analog to Digital Converter (ADC), in order to quantify the input signal. However, as the ADC has a switch constantly commuting on its input it will cause perturbations on the reference voltage provided by the Bandgap circuit. Thus, it will interfere with the normal behaviour of the Bandgap circuit, which will longer be capable of provide the desired reference voltage. Besides, if the reference voltage is not constant in the desired value the output code generated by the ADC will have errors. In order to avoid conversion errors it will be needed to introduce a buffer between the Bandgap and the ADC. Thus, taking advantage from the characteristics of the buffer (low output impedance, high input impedance and unitary gain) the system will be capable of recover from the perturbations introduced by the ADC in the reference voltage. Therefore, in this thesis are studied some of the already existing architectures of buffers, in order to see the advantages and disadvantages of each one. This way were chosen the best three architectures from a theoretical point of view, to implement and simulate, to obtain all the needed information in order to better compare them

Exploiting the bulk-driven approach in CMOS analogue amplifier design

This thesis presents a collection of new novel techniques using the bulk-driven approach, which can lead to performance enhancement in the field of CMOS analogue amplifier design under the very low-supply voltage constraints. In this thesis, three application areas of the bulk-driven approach are focused – at the input-stage of differential pairs, at the source followers, and at the cascode devices. For the input stage of differential pairs, this thesis proposes two new novel circuit design techniques. One of them utilises the concept of the replica-biased scheme in order to solve the non-linearity and latch-up issues, which are the potential problems that come along with the bulk-driven approach. The other proposed circuit design technique utilises the flipped voltage scheme and the Quasi-Floating Gate technique in order to achieve low-power high-speed performances, and furthermore the reversed-biased diode concept to overcome the issue of degraded input impedance characteristics that come along with the bulk-driven approach. Applying the bulk-driven approach in source followers is a new type of circuit blocks in CMOS analogue field, in which to the author’s best knowledge has not been proposed at any literatures in the past. This thesis presents the bulk-driven version of the flipped voltage followers and super source followers, which can lead to eliminating the DC level shift. Furthermore, a technique for programming the DC level shift less than the threshold voltage of a MOSFET, which cannot be achieved by conventional types of source followers, is presented. The effectiveness of the cascode device using the bulk-driven approach is validated by implementing it in a complete schematics design of a fully differential bulk-driven operational transcoductance amplifier (OTA). This proposal leads to solving the lowtranconductance problem of a bulk-driven differential pair, and in effect the open loop gain of the OTA exceeds 60dB using a 0.35μm CMOS technology. The final part of this thesis provides the study result of the input capacitance of a bulk-driven buffer. To verify the use of the BSIM3 MOSFET model in the simulation for predicting the input capacitance, the measurement data of the fabricated device are compared with the postlayout simulation results