31 research outputs found

    Designing Broadband over Power Lines Networks Using the Techno-Economic Pedagogical (TEP) Method ñ€“ Part II: Overhead Low-Voltage and Medium-Voltage Channels and Their Modal Transmission Characteristics

    Get PDF
    Based on the techno-economic pedagogical (TEP) method proposed in [1] that is suitable for designing Broadband over Power Lines (BPL) networks in transmission and distribution power grids, this paper examines the broadband potential of overhead low-voltage/broadband over power lines (LV/BPL) and medium-voltage/broadband over power lines (MV/BPL) networks.In this paper, on the basis of the set of linear simplifications and techno-economic metrics already presented in [1], TEP method demonstrates to undergraduate electrical and computer engineering (ECE) students the behavior of overhead LV/BPL and MV/BPL networks in terms of their modal transmission characteristics when different overhead LV/BPL and MV/BPL topologies occur.The contribution of this paper is four-fold. First, the factors influencing modal transmission characteristics of overhead LV/BPL and MV/BPL networks are investigated with regard to their spectral behavior and end-to-end channel attenuation. Second, the impact of the multiplicity of branches at the same junction is first examined. In the light of cascaded two-way power dividers, TEP method is extended so as to cope with more complex BPL topologies offering a new simplified and accurate circuital approximation. Third, apart from the broadband transmission characteristics of the entire overhead distribution power grid, a consequence of the application of TEP method is that it helps towards the intraoperability/interoperability of overhead LV/BPL and MV/BPL systems under a common PHY framework in the concept of a unified distribution smart grid (SG) power network. Fourth, TEP method can be demonstrated to undergraduate ECE students as case study in order to stimulate their interest for Microwave Engineering and Circuit/System Engineering courses. Citation: Lazaropoulos, A. (2015). Designing Broadband over Power Lines Networks Using the Techno-Economic Pedagogical (TEP) Method ñ€“ Part II: Overhead Low-Voltage and Medium-Voltage Channels and Their Modal Transmission Characteristics. Trends In Renewable Energy, 1(2), 59-86. doi:10.17737/tre.2015.1.2.00

    Simulation-Based Evaluation of the Performance of Broadband over Power Lines with Multiple Repeaters in Linear Topology of Distribution Substations

    Get PDF
    Broadband over Power Lines (BPL) is considered a promising communication technology in the concept of Smart Grids. This paper evaluates networks based on BPL, with a focus on the impact of repeaters in the linear topology of distribution substations. In large-scale Smart Grids network planning, positions of repeaters have to be carefully chosen. This article should help to determine such positions and limitations of BPL linear topology networks. Laboratory and on-field measurements and their results are presented in this article. Results show the impact of repeater’s deployment for different testing methodologies also with regard to other already presented studies. Measured values and the determined impacts of repeaters are later used as input data for simulation of the linear BPL topology in terms of network throughput with multiple streams and bottlenecks. These occur especially on lines shared by multiple communicating nodes. Furthermore, the simulation investigates the balancing time of multiple data streams throughput. The simulation shows that the throughput balancing can occupy a significant time slot, up to tens of seconds before the throughput of different streams balances. Also, the more data is generated, the more time the balancing time takes. Additionally, the throughput drop caused by a repeater is determined into the range of 35–60%. Based on the measurement and simulation results, lessons learned are presented, and possible performance improvements are discussed

    Broadband Access for Students at East Tennessee State University

    Get PDF
    The purpose of this study was to determine the availability of Internet access for students attending East Tennessee State University during the fall semester 2013. It has been unknown to what degree broadband access is available in the East Tennessee State University service area that includes counties in East Tennessee, Southwest Virginia, and Western North Carolina. The research was conducted during the fall semester 2013 including the months of August, September, and October of 2011. Data were gathered by surveying currently enrolled students of the university. Seven hundred eighty-four students responded to the survey. The survey instrument covered areas of demographics and Internet connection type from home. In addition, the instrument covered usage of 3G/4G Mobile Broadband Service, ETSU computer labs, and high-speed Internet service for coursework. The results of the data analysis provided insight into the availability, frequency of use, and perceived importance of high-speed Internet access for students at ETSU. For example, over 95% of the respondents had either a high-speed Internet connection or 3G/4G Mobile Broadband Service at their place of residence. Fifteen percent were dissatisfied with their current high-speed Internet service. Approximately 70% reported that high-speed Internet service was very important in completing coursework. This study provided an increase in the body of knowledge related to Internet access for ETSU students and the counties surrounding the university

    Development of methodologies for deploying and implementing local & medium area broadband PLC networks in office and residential electric grids

    Get PDF
    The use of electrical networks for telecommunications has a long history. It has been known since the beginning of the twentieth century [Ahola03]. The idea of using electrical networks for broadband communications arose in the 1990s [Hrasnica et al 04]. Recent and growing research interest has indicated that PowerLine Communications (PLC) is the threshold for achieving broadband delivery particularly in very dispersed and low teledensity areas. Currently, there are numerous PLC trials and commercial deployments underway inside and outside South Africa. Nevertheless, these PLC deployments are very isolated, done without clear methodology and performance remains bound to the physical layout of the electrical network. Because of that high bandwidth broadband PLC systems are prone to poor performance and this in turn limits the acceptance and deployment of this emerging alternative broadband technology. Though, PLC technical challenges are being addressed, there has been little analysis and research work that is focused on the “Development of Methodologies for Deploying and Implementing Local & Medium Area Broadband Power Line in Residential and Office Electric Grids” that would lead to broadband PLC being adopted and be of greater use to non-broadband communities of South Africa. PLC is a term describing several different systems using electrical grid distribution wires for simultaneous distribution of data by superimposing an analog signal [Hrasnica et al 04]. The research proposed and presented broadband PLC methodologies for typical medium voltage and local voltage PLC networks. These methodologieswere implemented and experimented with in configurations which closely mirrored residential and office settings through laboratory and multibuilding experiments using commercial 2nd Generation Mitsubishi Electric PLC technology. Research results presented not only serve to provide insight into broadband PLC but also how it handled broadband applications (communications), competed and compared with other technologies such as Ethernet LAN. In combination with networking communication theories, the research explored and analyzed the extent of PLC in providing broadband communication to residential and office electric grids at the University Fort Hare, Computer Science Department

    Rethinking universal service for a next generation network environment

    Get PDF
    There is a clear need, in view of significant competitive, technological and service changes taking place in the telecommunications sector, to review universal service obligations, their coverage, how they are financed and who is responsible for providing them. In many OECD countries, a primary longer term issue is how to provide universal service in the new competitive environment where voice is ubiquitous and cheap, voice revenues low and where voice has become just one of many applications provided on networks. Access too is changing, with more choice in platforms available that allow access to voice applications. This paper overviews the main issues that need to be examined in such a review with a view to the reform of universal service in a way consistent with emerging technological realities and competitive circumstances. [Introduction

    Electromagnetic compatibility of power line communication systems

    Get PDF
    The power system has been used for communication purposes for many decades, although it was mainly the power utility companies that used low bit rates for control and monitoring purposes. In the last ten years, however, the deregulation of the power and telecommunication markets has spurred the idea of using and commercializing the power networks for a range of new communication applications and services. The idea has been developed and implemented into both, narrowband and broadband systems, which are defined in terms of the operation frequency band. Depending on the frequency band, the systems over powerlines can be: Narrow-band. They use frequencies ranging from 3-148.5 kHz in Europe, with the upper frequency extending up to 500 kHz in the United States and Japan. In Europe, this frequency range is standardized by CENELEC Standard EN 50065. Broadband. The used frequency range is 1-30MHz; 1-15MHz for outdoor systems and 15-30MHz for indoor systems. In this frequency range, the standardization situation is still unclear and there exist no regulations. The developed applications and systems use different parts of the power network: medium voltage (MV) and low voltage (LV) cabling for outdoor applications and building cabling for indoor applications. These cables are designed and optimized for power transmission at frequencies of 50/60Hz and represent a hostile medium for transmissions at higher frequencies. This thesis concentrates on electromagnetic compatibility (EMC) aspects and some optimization issues of the broadband systems, currently known as Powerline Communications (PLC) or Broadband Power Line (BPL). The work presented here was preformed in the framework of the European project OPERA (http://www.ist-opera.org/). A short description of the project is given in Chapter 1. The second chapter presents the basis, introduction, description and state of the art of the topics of interest for this thesis. That chapter is divided into three parts. Each of these parts starts with a short introduction to the topic to be addressed. The introductions are intended for those not familiar with the topic at hand and they can be skipped by those already knowledgeable of it. The first part of Chapter 2 gives an overview and introduction to telecommunication issues relevant to the thesis, as well as the general technical specifications of the OPERA system. The second part deals with the transmission medium which, for the case of PLC, is the power system. The fundamentals and the different components of the PLC system are given there and the state of the art regarding the transmission channel is presented. The third part deals with the EMC and standardization issues related to the technology. The main contributions of the thesis are presented in chapters 3 to 7. The PLC technology distinguishes itself from other technologies in that it uses already existing, ubiquitous wiring, so that no new infrastructure is needed. On the other hand, using a channel designed originally for other purposes means that it is not optimized for the frequencies and applications of interest for broadband transmission. If PLC is to compete with other technologies, these problems have to be well understood and solved, so that the system can be optimized by taking into account the parameters and constrains of the already existing medium. Although the PLC system is being improved continuously, there are still concerns about emissions, immunity and standardization. These issues are important since PLC operates in an environment already populated by other services at the same frequencies, so that fair co-existence is needed. Moreover, the PLC modem has a combined mains and telecom port and, as a consequence, the standards for conducted emissions from those two types of ports are not directly applicable. In addition, the symmetry of the cables used is low and, therefore, emissions are higher than, for example, emissions from twisted pair cables used in xDSL. A good understanding of emissions and immunity in PLC systems is therefore of great importance for the optimization of the system and for EMC standardization to be based on objective technical criteria. Even if the basic phenomena are essentially the same as for any other wire transmission system, the complexity and variability of the topologies of existing structures is so large that simple, straightforward solutions are often not applicable. Emissions from the cabling are primarily due to the common mode signals. Part of the energy in this mode is injected by the imperfectly balanced output stages of the PLC modems themselves. In addition, the common mode appears at punctual imbalanced discontinuities and distributed asymmetry along the PLC signal path in the power cables. Chapter 3 presents the work performed to improve our understanding of the sources of the common-mode current and the parameters that influence its behavior, including related measurements and simulations. For the purpose of this study, a model house was built at the EPFL's test site. Different cablings were used to study the influence of different parameters on the behavior of the common-mode current since it is the main source for both types of emissions, conducted and radiated ones. The influence of different parameters such as the cable terminations, the symmetry of the termination, the height of the conductors above the ground, the presence of power outlets, switches, empty and occupied sockets and the topology, are analyzed. The data are also used to test two methods used to simulate the differential-to-common-mode conversion and the conducted emissions, namely the transmission line model and the full wave approach provided by the Method of Moments through the Numerical Electromagnetic Code (NEC). In Chapter 4, problems related to PLC immunity testing are treated. We show that the conversion of the differential mode to the common mode is coupled with the reverse conversion by reciprocity. Due to the low symmetry of PLC cabling, part of the injected common mode test signal is converted into a differential mode signal that interferes with the wanted signal at the input of the modem being tested. Depending on the actual symmetry of the Coupling-Decoupling Network (CDN), not specified in the standards, the immunity test may yield erroneous results due to the effect of this differential mode component. Working under the assumption that the CDN is built to exhibit a symmetry similar to that of PLC networks as inferred from its longitudinal conversion loss, we estimate the differential mode disturbance level that the modems should withstand from a narrowband interferer. The bit error rate induced by the presence of the disturbing differential mode current from the CDN is also estimated, for a total physical channel transmission rate of 200 Mbps, to be of the order of 1×10-5 to 5×10-5. Since these rates can be handled by error correcting coding and MAC ARQ procedures, it is concluded that the modems are not likely to suffer any severe performance degradation due to immunity testing if the CDN exhibits a symmetry similar to that of PLC networks. Simulating the complete PLC network or any significant part of it using numerical techniques such as the method of moments proves to be of limited practical use due to the fact that PLC networks extend over many wavelengths. The transmission line approximation, on the other hand, although more efficient and sufficiently accurate for differential mode calculations, is not directly applicable to simulate the EMC behavior since it neglects the antenna-mode currents that are significant contributors to the radiated emissions. Chapter 5 presents a novel approach to evaluate the antenna-mode currents using a modified transmission line theory, thus making this numerically efficient technique applicable to the estimation of emissions in PLC. An integral equation describing the antenna-mode currents along a two-wire transmission line is derived. It is further shown that, when the line cross-sectional dimensions are electrically small, the integral equation reduces to a pair of transmission line-like equations with equivalent line parameters (per-unit-length inductance and capacitance). The derived equations make it possible to compute the antenna mode currents using a traditional transmission line code with appropriate parameters. The derived equations are tested versus numerical results obtained using NEC and reasonably good agreement is found. Another important EMC issue related to PLC is the mitigation of emissions. Chapter 6 describes a technique that has been proposed to achieve a reduction of emissions associated with indoor PLC networks through the introduction of a 180° out-of-phase replica of the PLC signal into the unused neutral-ground circuit. A modification to this technique is proposed based on the selection of the appropriate amplitude and phase of the auxiliary signal, allowing a higher degree of field attenuation. A way of implementing this technique is proposed and studied, namely the integration of a required antenna into the PLC modems themselves. The measured fields very close to the modem allow the determination of the magnitude and phase of the compensation voltage. The proposed implementation should be used only to handle customer complaints, when emissions should be lowered at locations where PLC signals might cause unwanted interference or when additional capacity is required and it can be obtained through the gained signal to noise margin. Although, in principle, due to nonalignment of the wanted and the compensation field directions, minimizing one component of the field may result in an increase of the other components, we show that the application of the technique results in an overall average reduction of 10-20 dB of all the field components in the region of interest. In the same Chapter 6, we address the more general issue of the application of mitigation techniques' gained emissions margin to increase the overall throughput of PLC systems. We show that an increase in the signal power (made possible by the inclusion of mitigation techniques) leads to a considerable increase in the PLC channel capacity. Using a number of simplifications, we show that the capacity of the channel can indeed be increased by up to 66 Mbps for mitigation efficiencies of only 10 dB. We also present the results of laboratory measurements aimed at studying, under controlled conditions, different characteristics of notching in OPERA PLC modems, such as total and effective notch width, notch depth, maximum notch depth, etc. These measurements show that it is possible to obtain attenuations of up to about 45 dB for notches in all frequency bands, 10MHz, 20MHz and 30MHz. What differs for these three bands is the minimum number of carriers that need to be notched to obtain that maximum attenuation. This is an important point, since, to implement notches that have the required depth and width, one must know how many subcarriers to suppress and how deep these need to be reduced. High density PLC deployment requires the increase of overall system data rate. To achieve the higher data rates, frequency reuse in these systems is needed. In Chapter 7, we present the idea for using so-called blocking filters as a possible solution for a frequency reuse. Experimental data obtained on a real distribution network show that the use of blocking filters can, in certain cases, ensure high enough RF separation of the LV feeders belonging to the same substation. In some cases, even with the possibility to design and integrate effective blocking filters, the system needs to provide additional synchronization mechanisms for frequency reuse

    Comprehensive literature review on delay tolerant network (DTN) framework for improving the efficiency of internet connection in rural regions of Malaysia

    Get PDF
    This paper brief in detail the technology reviews of current available technologies and literature reviews that starts with the history of the Internet and the understanding of the working of the Internet through a conceptual model of TCP/IP and OSI models, the numerous technologies developed to cater for different connectivity environments and recent popular topics in the field of communication technologies. Detailed review is done on the subject of Delay-Tolerant Networking (DTN), the chosen technology from which the intended framework can be proposed for improving the efficiency of internet connections. From these literatures, comparisons are made to find the best possible combinations of technologies to design a mini- mum viable product, followed by a generic DTN framework

    Achieving the Internal Market for e-communications. CEPS Task Force Reports, 20 June 2008

    Get PDF
    Over the past two years, the debate on the review of the EU regulatory framework for electronic communications has become hectic. After the European Commission adopted its proposed set of measures in November 2007, the European Parliament has shown an unprecedented interest in topics such as spectrum policy, functional separation of the incumbents’ networks, the creation of a new European authority on telecoms, etc. After the successful experience of the first CEPS Task Force on “Policy Challenges for the Information Superhighway”, which ended in June 2006, a new Task Force on “Achieving the Internal Market for e-communications” was launched by CEPS with the explicit aim to provide expertise to Members of the European Parliament in their reading of the proposed review. The Task Force was chaired by Magnus Lemmel, former Acting Director General at DG Enterprise, European Commission, and currently Senior Advisor at KREAB. This report summarises the results of the opinions that were expressed over five meetings, the last two of which took place inside the European Parliament. This highly influential report was drafted by Andrea Renda, Senior Research Fellow at CEPS

    Power Line Communications: A Platform for Sustainable Development

    Get PDF
    –E Abstract lectricity infrastructure together with information and communication technology (ICT) constitute a veritable platform for driving inclusive and sustainable development. However, last mile internet access in underdeveloped areas is limited by deficit telecommunications infrastructure. This is mainly due to the cost associated with deploying telecommunication distribution networks and the low returns on investments associated with underdeveloped areas. The availability of electric power grids which can be used as telecommunication distribution networks, makes the idea of using power line communication and wireless networks a realistic means of providing communications service to underdeveloped areas.On the other hand, electricity utilities needs an efficient and cost effective means of operating and managing the electric grid. This paper reviews different power line communications technologies that can used to achieve a smart grid model that provides a sustainable electricity and ICT infrastructure for development in Africa
    corecore