Demonstrating doubly-differential quadrature phase shift keying in the optical domain

We report for the first time the experimental demonstration of doubly differential quadrature phase shift keying (DDQPSK) using optical coherent detection. This method is more robust against high frequency offsets (FO) than conventional single differential quadrature phase shift keying (SDQPSK) with offset compensation. DDQPSK is shown to be able to compensate large FOs (up to the baud rate) and has lower computational requirements than other FO compensation methods. DDQPSK is a simple algorithm to implement in a real-time decoder for optical burst switched network scenarios. Simulation results are also provided, which show good agreement with the experimental results for both SDQPSK and DDQPSK transmissions

Multiuser non coherent massive MIMO schemes based on DPSK for future communication systems

The explosive usage of rich multimedia content in wireless devices has overloaded the communication networks. Moreover, the fifth generation (5G) of wireless communications involves new requirements in the radio access network (RAN) which require higher network capacities and new capabilities such as ultra-reliable and low-latency communication (URLLC), vehicular communications or augmented reality. All this has encouraged a remarkable spectrum crisis in the RF bands. A need for searching alternative techniques with more spectral efficiency to accommodate the needs of future emerging wireless communications is emerging. In this context, massive MIMO (m-MIMO) systems have been proposed as a promising solution for providing a substantial increase in the network capacity, becoming one of the key enabling technologies for 5G and beyond. m-MIMO provides high spectral- and energy-efficiency thanks to the deployment of a large number of antennas at the BS. However, we have to take into account that the current communication technologies are based on coherent transmission techniques so far, which require the transmission of a huge amount of signaling. This drawback is escalating with the excessive available number of antennas in m-MIMO. Therefore, the differential encoding and non coherent (NC) detection are an alternative solution to circumvent the drawbacks of m-MIMO in coherent systems. This Ph.D. Thesis is focused on signal processing techniques for NC detection in conjunction with m-MIMO, proposing new constellation designs and NC detection algorithms, where the information is transmitted in the signal differential phase. First, we design new constellation schemes for an uplink multiuser NC m-MIMO system in Rayleigh fading channels. These designs allow us to separate the users' signals at the receiver thanks to a one-to-one correspondence between the constellation for each user and the received joint constellation. Two approaches are considered in terms of BER: each user achieves a different performance and, on the other hand, the same performance is provided for all users. We analyze the number of antennas needed for those designs and compare to the required number by other designs in the literature. It is shown that our designs based on DPSK require a lower number of antennas than that required by their counterpart schemes based on energy. In addition, we compare the performance to their coherent counterpart systems, resulting NC-m-MIMO based on DPSK capable of outperforming the coherent systems with the suitable designs. Second, in order to reduce the number of antennas required for a target performance we propose a multi-user bit interleaved coded modulation - iterative decoding (BICM-ID) scheme as channel coding for a NC-m-MIMO system based on DPSK. We propose a novel NC approach for calculating EXIT curves based on the number of antennas. Then using the EXIT chart we find the best channel coding scheme for our NC-m-MIMO proposal. We show that the number of users served by the BS can be increased with a 70% reduction in the number of antennas with respect to the case without channel coding. In particular, we show that with 100 antennas for error protection equal design for all users and a coding rate of 1/2 we achieve the minimum probability of error. Third, we consider that current scenarios such as backhaul wireless systems, rural or suburban environments, and even new device-to-device (D2D) communications or the communications in higher frequencies (millimeter and the emerging ones in terahertz frequencies) can have a predominant line-of-sight (LOS) component, modeled by Rician fading. For all these new possible scenarios in 5G, we analyze the behavior of the NC m-MIMO systems when we have a Rician fading. We present a new constellation design to overcome the problem of the LOS channel component, as well as an associated detection algorithm to separate each user in reception taking into account the characterization of the constellation. In addition, for contemplating a more realistic scenario, we propose grouping users which experience a Rayleigh fading with those with Rician fading, analyzing the SINR and the performance of such combination in a multi-user NC m-MIMO system based on M-DPSK. The adequate user grouping allows unifying the constellation for both groups of users and the detection algorithm, reducing the complexity of the receiver. Also, the number of users that may be multiplexed may be further increased thanks to the improved performance. In the fourth part of this Thesis, we analyse the performance of multi-user NC m- MIMO based on DPSK in real environments and practical channels defined for the current standards such as LTE, the future technologies such as 5G and even for communications in the terahertz band. For this purpose, we use a metric to model the time-varying characteristics of the practical channels. We employ again the EXIT charts tool for analyzing and designing iteratively decoded systems. This analysis allows us to obtain an estimate of the degradation of the system's performance imposed by realistic channels. Hence, we show that our proposed system is robust to temporal variations, thus it is more recommendable the employment of NC-m-MIMO-DPSK in the future communication standards such as 5G. In order to reduce he number of hardware resources required in terms of RF chains, facilitating its implementation in a real system, we propose incorporating differential spatial modulation (DSM). We present and analyze a novel multiuser scheme for NC-m-MIMO combined with DSM with which we can see that the number of antennas is not a affected by the incorporation of DSM, even we have an improvement on the performance with respect to the coherent case. Finally, we study the viability of multiplexing users by constellation schemes against classical multiplexing techniques such as time division multiple access (TDMA). In order to fully characterize the system performance we analyze the block error rate (BLER) and the throughput of a NC-m-MIMO system. The results show a significant advantage regarding the number of antennas for multiplexing in the constellation against TDMA. However, in some cases, the demodulation of multiple users in constellation could require an excessively large number of antennas compared to TDMA. Therefore, it is necessary to properly manage the tradeoff between throughout and the number of antennas, to reach an optimal operational point, as shown in this Thesis.El inmenso uso de contenido multimedia en los dispositivos inalámbricos ha sobrecargado las redes de comunicaciones. Además, la quinta generación (5G) de sistemas de comunicaciones demanda nuevos requisitos para la red de acceso radio, la cual requiere ofrecer capacidades de red mayores y nuevas funcionalidades como comunicaciones ultra fiables y con muy poca letancia (URLLC), comunicaciones vehiculares o aplicaciones como la realidad aumentada. Todo esto ha propiciado una crisis notable en el espectro electromagnético, lo que ha llevado a una necesidad por buscar técnicas alternativas con más eficiencia espectral para acomodar todos los requisitos de las tecnologías de comunicaciones emergentes y futuras. En este contexto, los sistemas multi antena masivos, conocidos como massive MIMO, m-MIMO, han sido propuestos como una solución prometedora que proporciona un incremento substancial de la capacidad de red, convirtiéndose en una de las tecnologías claves para el 5G. Los sistemas m-MIMO elevan enormemente el número de antenas en la estación base, lo que les permite ofrecer alta eficiencia espectral y energética. No obstante, tenemos que tener en cuenta que las actuales tecnologías de comunicaciones emplean técnicas coherentes, las cuales requieren de información del estado del canal y por ello la transmisión de una enorme cantidad de información de señalización. Este inconveniente se ve agravado en el caso del m-MIMO debido al enorme número de antenas. Por ello, la codificación diferencial y la detección no coherente (NC) son una solución alternativa para solventar el problema de m-MIMO en los sistemas coherentes. Esta Tesis se centra en las técnicas de procesado de señal para detección NC junto con m-MIMO, proponiendo nuevos esquemas de constelación y algoritmos de detección NC, donde la información sea transmitida en la diferencia de fase de la señal. Primero, diseñamos nuevas constelaciones para un sistema multi usuario NC en m- MIMO en enlace ascendente (uplink) en canales con desvanecimiento tipo Rayleigh. Estos diseños nos permiten separar las señales de los usuarios en el receptor gracias a la correspondencia unívoca entre la constelación de cada usuario individual y la constelación conjunta recibida en la estación base. Hemos considerado dos enfoques para el diseño en términos de probabilidad de error: cada usuario consigue un rendimiento distinto, mientras que por otro lado, todos los usuarios son capaces de recibir las mismas prestaciones de probabilidad de error. Analizamos el número de antenas necesario para estos diseños y comparamos con el número requerido por otros diseños propuestos en la literatura. Nuestro diseño basado en DPSK requiere un número menor de antenas comparado con los sistemas basados en detección de energía. También comparamos con su homólogo coherente, resultando que NC-m-MIMO basado en DPSK es capaz de superar a los sistemas coherentes con los diseños adecuados. En segundo lugar, para reducir el número de antenas requerido para un rendimiento dado, proponemos incluir un esquema de codificación de canal. Hemos optado por un esquema de modulación codificado por bit entrelazado y decodificación iterativa (BICMID). Hemos empleado la herramienta EXIT chart para el diseño de la codificación de canal, proponiendo un nuevo enfoque para calcular las curvas EXIT de forma NC y basadas en el número de antenas. Los resultados muestran que el número de usuarios servidos por la estación base puede ser incrementado reduciendo un 70% el número de antenas con respecto al caso sin codificación de canal. En particular, para un array de 100 antenas y un diseño que ofrezca iguales prestaciones a todos los usuarios, con un código de tasa 1=2, podemos conseguir la mínima probabilidad de error. En tercer lugar, consideramos escenarios donde el canal tenga una componente predominante de visión directa (LOS) con la estación base modelada mediante un desvanecimiento tipo Rician. Por ejemplo, sistemas inalámbricos de backhaul, entornos rurales o sub urbanos, comunicaciones entre dispositivos (D2D), también cuando nos movemos hacia frecuencias superiores como son en la banda de milimétricas o más recientemente, la banda de terahercios para buscar mayores anchos de banda. Todos estos escenarios están contemplados en el futuro 5G. Los diseños presentados para canales Rayleigh ya no son válidos debido a la componente LOS del canal, por ello presentamos un nuevo diseño de constelación que resuelve el problema de la componente LOS, así como una guía para diseñar nuevas constelaciones. También proponemos un algoritmo asociado al diseñno de la constelación para poder separar a los usuarios en recepción. Además, para contemplar un escenario más realista donde podamos encontrar tanto desvanecimiento Rayleigh como Rice, proponemos agrupar usuarios de ambos grupos, analizando su rendimiento y relación señal a interferencia en la combinación. El adecuado agrupamiento permite unificar el diseño de la constelación para ambos desvanecimientos y por tanto reducir la complejidad en el receptor. También, el número de usuarios multiplicados en la constelación podría ser incrementado, gracias a la mejora en el rendimiento. El cuarto módulo de esta tesis es dedicado a analizar el rendimiento de los diseños propuestos en presencia de canales reales, donde disponemos de variabilidad temporal y en frecuencia. Proponemos usar una métrica que modela las características de la variabilidad temporal y, usando de nuevo la herramienta EXIT, analizamos los sistemas decodificados iterativamente considerando ahora los parámetros prácticos del canal. Este análisis nos permite obtener una estimación de la degradación que sufre el rendimiento del sistema impuesto por canales reales. Los resultados muestran que los sistemas NC-m-MIMO basados en DPSK son muy robustos a la variabilidad temporal por lo que son recomendables para los nuevos escenarios propuestos por el 5G, donde el canal cambia rápidamente. Otra consideración para introducir los sistemas NC con m-MIMO es la problemática de necesitar muchas cadenas de radio frecuencia que llevarían a tamaños de dispositivos enormes. Para reducir este número se propone la modulación espacial. En esta Tesis, estudiamos su uso con los sistemas NC, proponiendo una solución de modulación espacial diferencial para esquemas con múltiples usuarios combinado con NC-m-MIMO. Finalmente, estudiamos la viabilidad de multiplexar usuarios en la constelación frente a usar técnicas clásicas de multiplexación como TDMA. Para caracterizar completamente el rendimiento del sistema, analizamos la tasa de error de bloque (BLER) y el throughput de un sistema NC-m-MIMO. Los resultados muestran una ventaja significativa en cuanto al número de antennas para multiplexar usuarios en la constelación frente al requerido por TDMA. No obstante, en algunos casos, la demodulación de múltiples usuarios en la constelación podría requerir un número de antennas excesivamente grande comparado con la multiplexación en el tiempo. Por ello, es necesario gestionar adecuadamente un balance entre el throughput y el número de antenas para alcanzar un punto operacional óptimo, como se muestra en esta Tesis.Programa Oficial de Doctorado en Multimedia y Comunicaciones por la Universidad Carlos III de Madrid y la Universidad Rey Juan CarlosPresidente: Ana Isabel Pérez Neira.- Secretario: Máximo Morales Céspedes.- Vocal: María del Carmen Aguayo Torre

Proceedings of the Mobile Satellite Conference

A satellite-based mobile communications system provides voice and data communications to mobile users over a vast geographic area. The technical and service characteristics of mobile satellite systems (MSSs) are presented and form an in-depth view of the current MSS status at the system and subsystem levels. Major emphasis is placed on developments, current and future, in the following critical MSS technology areas: vehicle antennas, networking, modulation and coding, speech compression, channel characterization, space segment technology and MSS experiments. Also, the mobile satellite communications needs of government agencies are addressed, as is the MSS potential to fulfill them

Techniques of detection, estimation and coding for fading channels

The thesis describes techniques of detection, coding and estimation, for use in high speed serial modems operating over fading channels such as HF radio and land mobile radio links. The performance of the various systems that employ the above techniques are obtained via computer simulation tests. A review of the characteristics of HF radio channels is first presented, leading to the development of an appropriate channel model which imposes Rayleigh fading on the transmitted signal. Detection processes for a 4.8 kbit/s HF radio modem are then discussed, the emphasis, here, being on variants of the maximum likelihood detector that is implemented by the Viterbi algorithm. The performance of these detectors are compared with that of a nonlinear equalizer operating under the same conditions, and the detector which offers the best compromise between performance and complexity is chosen for further tests. Forward error correction, in the form of trellis coded modulation, is next introduced. An appropriate 8-PSK coded modulation scheme is discussed, and its operation over the above mentioned HF radio modem is evaluated. Performance comparisons are made of the coded and uncoded systems. Channel estimation techniques for fast fading channels akin to cellular land mobile radio links, are next discussed. A suitable model for a fast fading channel is developed, and some novel estimators are tested over this channel. Computer simulation tests are also used to study the feasibility of the simultaneous transmission of two 4-level QAM signals occupying the same frequency band, when each of these signals are transmitted at 24 kbit/s over two independently fading channels, to a single receiver. A novel combined detector/estimator is developed for this purpose. Finally, the performance of the complete 4.8 kbit/s HF radio modem is obtained, when all the functions of detection, estimation and prefiltering are present, where the prefilter and associated processor use a recently developed technique for the adjustment of its tap gains and for the estimation of the minimum phase sampled impulse response

Adaptive equalisation for fading digital communication channels

This thesis considers the design of new adaptive equalisers for fading digital communication channels. The role of equalisation is discussed in the context of the functions of a digital radio communication system and both conventional and more recent novel equaliser designs are described. The application of recurrent neural networks to the problem of equalisation is developed from a theoretical study of a single node structure to the design of multinode structures. These neural networks are shown to cancel intersymbol interference in a manner mimicking conventional techniques and simulations demonstrate their sensitivity to symbol estimation errors. In addition the error mechanisms of conventional maximum likelihood equalisers operating on rapidly time-varying channels are investigated and highlight the problems of channel estimation using delayed and often incorrect symbol estimates. The relative sensitivity of Bayesian equalisation techniques to errors in the channel estimate is studied and demonstrates that the structure's equalisation capability is also susceptible to such errors. Applications of multiple channel estimator methods are developed, leading to reduced complexity structures which trade performance for a smaller computational load. These novel structures are shown to provide an improvement over the conventional techniques, especially for rapidly time-varying channels, by reducing the time delay in the channel estimation process. Finally, the use of confidence measures of the equaliser's symbol estimates in order to improve channel estimation is studied and isolates the critical areas in the development of the technique — the production of reliable confidence measures by the equalisers and the statistics of symbol estimation error bursts

Multipath propagation models for near line-of-sight conditions

This thesis analyzes the behaviour of a multipath channel for suburban and semi-rural areas in which line of sight (LOS) or near LOS exists between the transmitter and receiver. The objective is to characterize the broadband channel for such areas. The thesis is divided into five major parts: a background and literature survey, a theoretical analysis, experimental measurements which validate the analysis, applications to practical communication channels and a study of the effects of such a channel on typical signal waveforms. The amplitudes and delay spread of a multipath model for such an environment are studied, based on a theoretical analysis of scattering from finite flat surfaces which model building walls. A broadband channel model is proposed based on the analysis. The next part of the thesis presents experimental measurements on multipath communication channels in suburban and semi-rural areas, which have LOS or near LOS propagation. The results validate the theoretical analysis. It is found that the channel is either good or very bad. The latter usually occurs close to buildings where a single dominant reflection with a relative delay of less than a microsecond produces a periodic severe fading and distortion of the signal, often making a link unusable. The area for which the channel is bad depends on the size of the building. The thesis then considers applications of the broadband channel model and studies the effects of the proposed channel model on typical communication waveforms such as QPSK, direct sequence spread spectrum and OFDM. For the QPSK waveform, the effects of a single dominant reflection on the timing and carrier recovery of a coherent demodulator are studied. A methodology is also outlined for determining which locations in a defined area will show the behaviour associated with a bad channel

Advanced OFDM systems for terrestrial multimedia links

Recently, there has been considerable discussion about new wireless technologies and standards able to achieve high data rates. Due to the recent advances of digital signal processing and Very Large Scale Integration (VLSI) technologies, the initial obstacles encountered for the implementation of Orthogonal Frequency Division Multiplexing (OFDM) modulation schemes, such as massive complex multiplications and high speed memory accesses, do not exist anymore. OFDM offers strong multipath protection due to the insertion of the guard interval; in particular, the OFDM-based DVB-T standard had proved to offer excellent performance for the broadcasting of multimedia streams with bitrates over ten megabits per second in difficult terrestrial propagation channels, for fixed and portable applications. Nevertheless, for mobile scenarios, improving the receiver design is not enough to achieve error-free transmission especially in presence of deep shadow and multipath fading and some modifications of the standard can be envisaged. To address long and medium range applications like live mobile wireless television production, some further modifications are required to adapt the modulated bandwidth and fully exploit channels up to 24MHz wide. For these reasons, an extended OFDM system is proposed that offers variable bandwidth, improved protection to shadow and multipath fading and enhanced robustness thanks to the insertion of deep time-interleaving coupled with a powerful turbo codes concatenated error correction scheme. The system parameters and the receiver architecture have been described in C++ and verified with extensive simulations. In particular, the study of the receiver algorithms was aimed to achieve the optimal tradeoff between performances and complexity. Moreover, the modulation/demodulation chain has been implemented in VHDL and a prototype system has been manufactured. Ongoing field trials are demonstrating the ability of the proposed system to successfully overcome the impairments due to mobile terrestrial channels, like multipath and shadow fading. For short range applications, Time-Division Multiplexing (TDM) is an efficient way to share the radio resource between multiple terminals. The main modulation parameters for a TDM system are discussed and it is shown that the 802.16a TDM OFDM physical layer fulfills the application requirements; some practical examples are given. A pre-distortion method is proposed that exploit the reciprocity of the radio channel to perform a partial channel inversion achieving improved performances with no modifications of existing receivers

Band sharing and satellite diversity techniques for CDMA.

High levels of interference between satellite constellation systems, fading and shadowing are a major problem for the successful performance of communication systems using the allocated L/S frequency bands for Non-Geostationary Earth Orbit (NGEO) satellites. As free spectrum is nonexistent, new systems wishing to operate in this band must co-exist with other users, both satellite and terrestrial. This research is mainly concerned with two subjects. Firstly, band sharing between different systems Code Division Multiple Access (CDMA) and Time Division Multiple Access (TDMA) has been evaluated for maximizing capacity and optimising efficiency of using the spectrum available. For the case of widened channel bandwidth of the CDMA channel, the overlapping was tested under different degrees of channel overlap and different orders of filters. The best result shows that at the optimum degree of channel overlap, capacity increases by up to 21%. For the case of fixed channel bandwidth, the optimum overlapping between CDMA systems depends on the filtering Roll-off factor and achieves an improvement of the spectrum efficiency of up to 13.4%. Also, for a number of narrowband signal users sharing a CDMA channel, the best location of narrowband signals to share spectrum with a CDMA system was found to be at the edge of the CDMA channel. Simulation models have been constructed and developed which show the combination of DS- CDMA techniques, forward error correction (FEC) code techniques and satellite diversity with Rake receiver for improving performance of interference, fading and shadowing under different environments. Voice activity factor has been considered to reduce the effect of multiple access interference (MAI). The results have shown that satellite diversity has a significant effect on the system performance and satellite diversity gain achieves an improvement up to 6dB. Further improvements have been achieved by including concatenated codes to provide different BER for different services. Sharing the frequency band between a number of Low Earth Orbit (LEO) satellite constellation systems is feasible and very useful but only for a limited number of LEOS satellite CDMA based constellations. Furthermore, satellite diversity is an essential factor to achieve a satisfactory level of service availability, especially for urban and suburban environments

Optimising the efficiency of coherent optical packet switched networks

There is a continuing need to increase throughput in optical networks to satisfy the demands of internet applications. However, the non-linear Shannon capacity of standard single mode fibre is being approached. Also, almost all of the power used in optical networks is used by electronic routers. One possible solution to deal with both problems is to use optical packet switching. Optical packet switching uses fast switching tuneable lasers, which can change wavelength in the order of a several nanoseconds, to dynamically vary wavelength assignments in a network, and thus achieve routing in the network without electronic routers. In addition, fast wavelength assignment reduces waiting times, resulting in better utilization of network resources. However, the frequency dynamics of the tuneable lasers after switching wavelengths increases the waiting times required to successfully transmit data packets. In this thesis, frequency and phase dynamics of a tuneable laser transmitter, after a wavelength switching event, are initially characterised accurately using a novel technique. The effects that the frequency dynamics have on the transmission of coherent optical communication signals are mitigated using doubly differential decoding, a new approach proposed in this work for application in optical packet switched networks. This technique reduces the waiting times required to successfully transmit data after a wavelength switching event, and this enhances overall network efficiency and throughput. In addition, this work proposes and demonstrates the use of a least-mean squares algorithm to overcome polarisation demultiplexing issues which are present in these networks, which also decreases waiting times, increases network efficiency, and improves system robustness

Radiated transient interferences in digital communication systems

In the Electromagnetic Compatibility research area, an unsolved interference problem is the measurement and evaluation of the distortion produced by radiated transient disturbances on digital communication systems. This impulsive noise, which is generated by switching devices or by sparks, is a broadband interference that covers the spectrum from DC to several hundreds of megahertz or some gigahertz. Additionally, this man-made noise is characterized by its short and random burst parameters, which make really challenging to measure it correctly. During the thesis, we have explained that impulsive noise is not properly measured and evaluated to prevent interference scenarios, when the EMC standard methodologies are applied. Detectors, such as the quasi-peak, frequency sweep measurements or signal-to-noise limiting evaluation described in the harmonized standards of the electromagnetic compatibility do not enable to determine beforehand the influence of transient interferences. Our strategy to overcome the non-profit measurement has been to perform novel measurement and evaluation techniques beyond EMC standards. The measurement technique developed joins the capabilities of EMI receivers and oscilloscope instrumentations to capture accurately the radiated transient interference. To carry out the measurement, the input stage of the EMI receiver is used for filtering and pre-amplifying purposes, conducting the IF output towards the oscilloscope, which is used for triggering and storage. Furthermore, a final post-processing stage is needed to obtain in time-domain the in-phase and quadrature components of the transient interference. Once the radiated transient interference has been measured properly, an accurate evaluation of the distortion produced to a digital communication system can be estimated. To evaluate the impact of the transient interference, a combination of the time-domain measurement with base-band simulation has been proposed to fulfil the thesis goal. The IQ time-domain measurement enables us to characterize the impulsive-noise present at the communication channel and determine the distortion produced to the digital communication system by means of base-band simulation. The procedure to determine the BER using the base-band simulation has been validated with experimental results, comparing the results reached with the developed methodology with the ones obtained when a communication system device is placed under radiated transient. Excellent results have been obtained employing the developed methodology, considering the interference produced by radiated transient to RFID or GSM communication systems Additionally, a new measurement methodology to obtain the amplitude probability diagram (APD) has been developed, offering the possibility to determine the bit-error-rate including limit lines at the APD diagram. This measurement method, based on captures obtained from a general purpose oscilloscope, makes it possible to obtain the APD measurement at any frequency band with the same accuracy provided by an EMI receiver. Furthermore, the post-processing tools using mathematical software produce the APD results rapidly at any bandwidth, and this makes it more powerful than employing an EMI receiver. The successful APD measurement system created is able to obtain the full-spectrum statistical measurement, employing several time-domain captures which can be acquired in practice immediately. In the final chapter of this thesis, the GSM system is interfered by radiated transients produced by sparks. The results provided by the APD diagram including the limit dots have been especially useful due to its fast capacity to interpret and quantify the degradation produced to the GSM system.En el camp de recerca de la compatibilitat electromagnètica, una de les problemàtiques no resoltes és la mesura i avaluació de les interferències produïdes per transitoris radiats sobre els equips de comunicació digitals. Aquest tipus de soroll impulsiu, que es genera per la commutació d' equips electrònics o guspires, és una interferència de banda ampla que ocupa l' espectre radioelèctric fins a diversos centenars de megahertz o algun gigahertz. A més, aquest soroll es caracteritza per la seva curta durada i l'aleatorietat dels seus paràmetres, i això fa que sigui molt complicat mesurar correctament la interferència. Al llarg de la tesi, hem explicat que el soroll impulsiu no es mesura ni s'avalua adequadament per evitar escenaris d'interferències si s'utilitzen les metodologies definides als estàndards d' EMC. Els detectors, com el de quasi-pic, l'escombratge en freqüència o l'avaluació basada en els límits relacionats amb la relació senyal a soroll no són vàlids per anticipar la influència de les interferències transitòries. La nostra estratègia per solucionar els problemes de les mesures normatives ha estat desenvolupar noves tècniques de mesura i avaluació fora dels estàndards d'EMC. La tècnica de mesura desenvolupada combina les capacitats dels receptors EMI i els oscil·loscopis per capturar la interferència transitòria radiada. Per realitzar les mesures, l'etapa d'entrada del receptor EMI s¿utilitza amb la finalitat de filtrar i preamplificar, enviant la sortida IF cap a l'oscil·loscopi, que es fa servir per detectar i emmagatzemar els transitoris. Per últim, en l'etapa de postprocessament, s'obtenen en el domini del temps els components en fase i en quadratura de la interferència transitòria. Una vegada s'ha mesurat adequadament la interferència radiada, es pot estimar correctament la distorsió produïda sobre els sistemes de comunicació digitals. Per avaluar l'impacte de la interferència transitòria i així complir amb l'objectiu de la tesi, s'ha proposat combinar les mesures en el domini del temps amb la simulació en banda base. La mesura IQ en el domini del temps ens permet caracteritzar el soroll impulsiu present al canal de comunicació i així determinar la distorsió produïda al sistema de comunicació digital mitjançant la simulació en banda base. El procediment per determinar el BER fent servir la simulació en banda base ha estat validat amb resultats experimentals, i s'han comparat els resultats obtinguts utilitzant la metodologia desenvolupada amb els resultats proporcionats directament col·locant un dispositiu sota la influència de transitoris radiats. Els excel¿lents resultats obtinguts considerant interferències produïdes sobre sistemes RFID i GSM han estat publicats. D'altra banda, també s'ha desenvolupat un nou mètode de mesura per adquirir el diagrama de probabilitat d¿amplitud (APD), oferint la possibilitat de determinar la probabilitat d'error en el bit incloent límits en el diagrama APD. Aquest mètode de mesura, basat en captures obtingudes mitjançant un oscil·loscopi de propòsit general, fa possible obtenir la mesura APD en qualsevol banda freqüencial amb la mateixa exactitud que proporciona un receptor EMI. A més, amb les eines de postprocessament desenvolupades és possible produir els resultats APD ràpidament i amb qualsevol amplada de banda, i això fa que sigui un mètode de mesura més potent que no pas utilitzar un receptor EMI. L'exitós sistema de mesura creat per obtenir l'APD és capaç d'obtenir la mesura estadística en tot l'espectre radiolèctric utilitzant poques captures en el domini del temps, les quals a la pràctica soón adquirides de forma inmediata. Al capítol final de la tesi, el sistema GMS és interferit per transistors radiats produïts per guspires. El resultat proporcionat pel diagrama APD, incloent-hi els límits, és especialment útil gràcies a la seva rapidesa per interpretar i quantificar la degradació produïda sobre el sistema GSM