Modelling and robust controller design for an underactuated self-balancing robot with uncertain parameter estimation

A comprehensive literature review of self-balancing robot (SBR) provides an insight to the strengths and limitations of the available control techniques for different applications. Most of the researchers have not included the payload and its variations in their investigations. To address this problem comprehensively, it was realized that a rigorous mathematical model of the SBR will help to design an effective control for the targeted system. A robust control for a two-wheeled SBR with unknown payload parameters is considered in these investigations. Although, its mechanical design has the advantage of additional maneuverability, however, the robot's stability is affected by changes in the rider's mass and height, which affect the robot's center of gravity (COG). Conventionally, variations in these parameters impact the performance of the controller that are designed with the assumption to operate under nominal values of the rider's mass and height. The proposed solution includes an extended Kalman filter (EKF) based sliding mode controller (SMC) with an extensive mathematical model describing the dynamics of the robot itself and the payload. The rider's mass and height are estimated using EKF and this information is used to improve the control of SBR. Significance of the proposed method is demonstrated by comparing simulation results with the conventional SMC under different scenarios as well as with other techniques in literature. The proposed method shows zero steady state error and no overshoot. Performance of the conventional SMC is improved with controller parameter estimation. Moreover, the stability issue in the reaching phase of the controller is also solved with the availability of parameter estimates. The proposed method is suitable for a wide range of indoor applications with no disturbance. This investigation provides a comprehensive comparison of available techniques to contextualize the proposed method within the scope of self-balancing robots for indoor applications

適応制御戦略に基づく車輪型二足歩行ロボットのバランス安定性の向上

Tohoku University林部充宏課

Load Disturbance Torque Estimation for Motor Drive Systems with Application to Electric Power Steering System

Motors are widely used in industries due to its ability to provide high mechanical power in speed and torque applications. Its flexibility to control and quick response are other reasons for its widespread use. Disturbance torque acting on the motor shaft is a major factor which affects the motor performance. Considering the load disturbance torque while designing the control for the motor makes the system more robust to load changes. Most disturbance observers are designed for steady state load conditions. The observer designed here considers a general case making no assumptions about the load torque dynamics. The observer design methods to be used under different disturbance conditions are also discussed and the performances compared. The designed observer is tested in a Hardware-in-Loop (HIL) setup for different load conditions. A motor load torque estimation based Fault Tolerant Control (FTC) is then designed for an Electric Power Steering (EPS) system

ROS-based Controller for a Two-Wheeled Self-Balancing Robot

In this article, a controller based on a Robot Operating System (ROS) for a two-wheeled self-balancing robot is designed. The proposed ROS architecture is open, allowing the integration of different sensors, actuators, and processing units. The low-cost robot was designed for educational purposes. It used an ESP32 microcontroller as the central unit, an MPU6050 Inertial Measurement Unit sensor, DC motors with encoders, and an L298N integrated circuit as a power stage. The mathematical model is analyzed through Newton-Euler and linearized around an equilibrium point. The control objective is to self-balance the robot to the vertical axis in the presence of disturbances. The proposed control is based on a bounded saturation, which is lightweight and easy to implement in embedded systems with low computational resources. Experimental results are performed in real-time under regulation, conditions far from the equilibrium point, and rejection of external disturbances. The results show a good performance, thus validating the mechanical design, the embedded system, and the control scheme. The proposed ROS architecture allows the incorporation of different modules, such as mapping, autonomous navigation, and manipulation, which contribute to studying robotics, control, and embedded systems

Advanced Strategies for Robot Manipulators

Amongst the robotic systems, robot manipulators have proven themselves to be of increasing importance and are widely adopted to substitute for human in repetitive and/or hazardous tasks. Modern manipulators are designed complicatedly and need to do more precise, crucial and critical tasks. So, the simple traditional control methods cannot be efficient, and advanced control strategies with considering special constraints are needed to establish. In spite of the fact that groundbreaking researches have been carried out in this realm until now, there are still many novel aspects which have to be explored

Control of Flexible Manipulator Robots Based on Dynamic Confined Space of Velocities: Dynamic Programming Approach

Linear Parameter Varying models-based Model Predictive Control (LPV-MPC) has stood out in manipulator robots because it presents well-rejection to dynamic uncertainties in flexible joints. However, it has become too weak when the MPC's optimization problem does not include kinematic constraints-based conditions. This paper uses dynamic confined space of velocities (DCSV) to include these conditions as a recursive polytopic constraint, guaranteeing optimal dependency on a simplex scheduling parameter. To this end, the local frame's velocities and torque/force preload of joints (related to violation of kinematic constraints) are associated with different time scale dynamics such that DCSV correlates them as a polytope. So, a classical LPV-MPC will be updated using a dynamic programming approach according to the DCSV-based polytope. As a result, one lemma about DCSV-based recursive polytope and a five-step procedure for two decoupled close-loop schemes with different time scales compose the LPV-MPC proposed method. Numerical validation shows that even for relevant flexibility situations, trajectory tracking performance is improved by tuning finite horizons and optimization problem constraints regarding DCSV's behavior