Practical formulation of the relation between filter specifications and the requirements for integrator circuits

The design of integrated, high-frequency, continuous-time filters has made considerable progress in the past few years. As the signal frequencies increase the design of the integrator circuits used in most of these filters becomes more critical. To give direction to the circuit design, minimum specifications for the gain and phase of the integrator circuits would be helpful. A practical method for obtaining these integrator specifications from the filter specifications is developed. The method is applied to a sixth-order Chebyshev band-pass filter, and the result is verified by computer simulatio

A wideband linear tunable CDTA and its application in field programmable analogue array

This document is the Accepted Manuscript version of the following article: Hu, Z., Wang, C., Sun, J. et al. ‘A wideband linear tunable CDTA and its application in field programmable analogue array’, Analog Integrated Circuits and Signal Processing, Vol. 88 (3): 465-483, September 2016. Under embargo. Embargo end date: 6 June 2017. The final publication is available at Springer via https://link.springer.com/article/10.1007%2Fs10470-016-0772-7 © Springer Science+Business Media New York 2016In this paper, a NMOS-based wideband low power and linear tunable transconductance current differencing transconductance amplifier (CDTA) is presented. Based on the NMOS CDTA, a novel simple and easily reconfigurable configurable analogue block (CAB) is designed. Moreover, using the novel CAB, a simple and versatile butterfly-shaped FPAA structure is introduced. The FPAA consists of six identical CABs, and it could realize six order current-mode low pass filter, second order current-mode universal filter, current-mode quadrature oscillator, current-mode multi-phase oscillator and current-mode multiplier for analog signal processing. The Cadence IC Design Tools 5.1.41 post-layout simulation and measurement results are included to confirm the theory.Peer reviewedFinal Accepted Versio

Transconductor and integrator circuits for integrated bipolar video frequency filters

A description is presented of novel transconductor and integrator circuits which can be used in integrated video frequency filters in bipolar technology. The transconductor consists of a parallel connection of a passive nominal transconductance and an active variable transconductance, resulting in good high-frequency performance up to 70 MHz and less than 1% linearity error for input signals up to 2V pp. The integrator incorporates an operation transconductance amplifier circuit which provides a tunable integrator phase. Simulation results for all circuits and for a fifth-order elliptic low-pass filter with a nominal cutoff frequency of 5 MHz are presente

CMOS OTA-C high-frequency sinusoidal oscillators

Several topology families are given to implement practical CMOS sinusoidal oscillators by using operational transconductance amplifier-capacitor (OTA-C) techniques. Design techniques are proposed taking into account the CMOS OTA's dominant nonidealities. Building blocks are presented for amplitude control, both by automatic gain control (AGC) schemes and by limitation schemes. Experimental results from 3- and 2- mu m CMOS (MOSIS) prototypes that exhibit oscillation frequencies of up to 69 MHz are obtained. The amplitudes can be adjusted between 1 V peak to peak and 100 mV peak to peak. Total harmonic distortions from 2.8% down to 0.2% have been measured experimentally.Comisión Interministerial de Ciencia y Tecnología ME87-000

A CMOS analog continuous-time delay line with adaptive delay-time control

A CMOS analog continuous-time delay line composed of cascaded first-order current-domain all-pass sections is discussed. Each all-pass section consists of CMOS transistors and a single capacitor. The operation is based on the square-law characteristic of an MOS transistor in saturation. The delay time per section can either be controlled by an external voltage or locked to an external reference frequency by means of a control system which features a large capture range. Experimental verification has been performed on two setups: an integrated cascade of 26 identical all-pass sections and a frequency-locking system breadboard built around two identical on-chip all-pass section

Automatic synthesis of analog layout : a survey

A review of recent research in the automatic synthesis of physical geometry for analog integrated circuits is presented. On introduction, an explanation of the difficulties involved in analog layout as opposed to digital layout is covered. Review of the literature then follows. Emphasis is placed on the exposition of general methods for addressing problems specific to analog layout, with the details of specific systems only being given when they surve to illustrate these methods well. The conclusion discusses problems remaining and offers a prediction as to how technology will evolve to solve them. It is argued that although progress has been and will continue to be made in the automation of analog IC layout, due to fundamental differences in the nature of analog IC design as opposed to digital design, it should not be expected that the level of automation of the former will reach that of the latter any time soon

0.5V 3rd-order Tunable gm-C Filter

This paper proposes a 3rd-order gm-C filter that operates with the extremely low voltage supply of 0.5V. The employed transconductor is capable for operating in an extremely low voltage power supply environment. A benefit offered by the employed transconductor is that the filter’s cut-off frequency can be tuned, through a dc control current, for relatively large ranges. The filter structure was designed using normal threshold transistors of a triple-well 0.13μm CMOS process and is operated under a 0.5V supply voltage; its behavior has been evaluated through simulation results by utilizing the Analog Design Environment of the Cadence software

Accurate automatic tuning circuit for bipolar integrated filters

An accurate automatic tuning circuit for tuning the cutoff frequency and Q-factor of high-frequency bipolar filters is presented. The circuit is based on a voltage controlled quadrature oscillator (VCO). The frequency and the RMS (root mean square) amplitude of the oscillator output signal are locked to the frequency and the RMS amplitude of a reference signal, respectively. Special attention is paid to the actual Q-factor in the oscillator. Experimental results for a breadboard circuit operating from 136 to 317 kHz are presente