On the test of single via related defects in digital VLSI designs

Vias are critical for digital circuit manufacturing, as they represent a common defect location, and a general DfM rule suggests replicating every instance for redundancy. When this is not achievable, a mandatory requirement is that the remaining single vias must be tested. We propose an automated method for generating tests and accurately evaluating test coverage of such defects, ready for use in any digital implementation flow and for integration within EDA tools, and also providing a useful quality metric. A prototype tool implementation and experimental results for an industrial case study are presented

Reducing Library Characterization Time for Cell-aware Test while Maintaining Test Quality

Cell-aware test (CAT) explicitly targets faults caused by defects inside library cells to improve test quality, compared with conventional automatic test pattern generation (ATPG) approaches, which target faults only at the boundaries of library cells. The CAT methodology consists of two stages. Stage 1, based on dedicated analog simulation, library characterization per cell identifies which cell-level test pattern detects which cell-internal defect; this detection information is encoded in a defect detection matrix (DDM). In Stage 2, with the DDMs as inputs, cell-aware ATPG generates chip-level test patterns per circuit design that is build up of interconnected instances of library cells. This paper focuses on Stage 1, library characterization, as both test quality and cost are determined by the set of cell-internal defects identified and simulated in the CAT tool flow. With the aim to achieve the best test quality, we first propose an approach to identify a comprehensive set, referred to as full set, of potential open- and short-defect locations based on cell layout. However, the full set of defects can be large even for a single cell, making the time cost of the defect simulation in Stage 1 unaffordable. Subsequently, to reduce the simulation time, we collapse the full set to a compact set of defects which serves as input of the defect simulation. The full set is stored for the diagnosis and failure analysis. With inspecting the simulation results, we propose a method to verify the test quality based on the compact set of defects and, if necessary, to compensate the test quality to the same level as that based on the full set of defects. For 351 combinational library cells in Cadence’s GPDK045 45nm library, we simulate only 5.4% defects from the full set to achieve the same test quality based on the full set of defects. In total, the simulation time, via linear extrapolation per cell, would be reduced by 96.4% compared with the time based on the full set of defects

Modelling and Test Generation for Crosstalk Faults in DSM Chips

In the era of deep submicron technology (DSM), many System-on-Chip (SoC) applications require the components to be operating at high clock speeds. With the shrinking feature size and ever increasing clock frequencies, the DSM technology has led to a well-known problem of Signal Integrity (SI) more especially in the connecting layout design. The increasing aspect ratios of metal wires and also the ratio of coupling capacitance over substrate capacitance result in electrical coupling of interconnects which leads to crosstalk problems. In this thesis, first the work carried out to model the crosstalk behaviour between aggressor and victim by considering the distributed RLGC parameters of interconnect and the coupling capacitance and mutual conductance between the two nets is presented. The proposed model also considers the RC linear models of the CMOS drivers and receivers. The behaviour of crosstalk in case of under etching problem has been studied and modelled by distributing and approximating the defect behaviour throughout the nets. Next, the proposed model has also been extended to model the behaviour of crosstalk in case of one victim is influenced by several aggressors by considering all aggressors have similar effect (worst-case) on victim. In all the above cases simulation experiments were also carried out and compared with well-known circuit simulation tool PSPICE. It has been proved that the generated crosstalk model is faster and the results generated are within 10% of error margin compared to latter simulation tool. Because of the accuracy and speed of the proposed model, the model is very useful for both SoC designers and test engineers to analyse the crosstalk behaviour. Each manufactured device needs to be tested thoroughly to ensure the functionality before its delivery. The test pattern generation for crosstalk faults is also necessary to test the corresponding crosstalk faults. In this thesis, the well-known PODEM algorithm for stuck-at faults is extended to generate the test patterns for crosstalk faults between single aggressor and single victim. To apply modified PODEM for crosstalk faults, the transition behaviour has been divided into two logic parts as before transition and after transition. After finding individually required test patterns for before transition and after transition, the generated logic vectors are appended to create transition test patterns for crosstalk faults. The developed algorithm is also applied for a few ISCAS 85 benchmark circuits and the fault coverage is found excellent in most circuits. With the incorporation of proposed algorithm into the ATPG tools, the efficiency of testing will be improved by generating the test patterns for crosstalk faults besides for the conventional stuck-at faults. In generating test patterns for crosstalk faults on single victim due to multiple aggressors, the modified PODEM algorithm is found to be more time consuming. The search capability of Genetic Algorithms in finding the required combination of several input factors for any optimized problem fascinated to apply GA for generating test patterns as generating the test pattern is also similar to finding the required vector out of several input transitions. Initially the GA is applied for generating test patterns for stuck-at faults and compared the results with PODEM algorithm. As the fault coverage is almost similar to the deterministic algorithm PODEM, the GA developed for stuck-at faults is extended to find test patterns for crosstalk faults between single aggressor and single victim. The elitist GA is also applied for a few ISCAS 85 benchmark circuits. Later the algorithm is extended to generate test patterns for worst-case crosstalk faults. It has been proved that elitist GA developed in this thesis is also very useful in generating test patterns for crosstalk faults especially for multiple aggressor and single victim crosstalk faults

A Defect-tolerant Cluster in a Mesh SRAM-based FPGA

International audienceIn this paper, we propose the implementation of multiple defect-tolerant techniques on an SRAM-based FPGA. These techniques include redundancy at both the logic block and intra-cluster interconnect. In the logic block, redundancy is implemented at the multiplexer level. Its efficiency is analyzed by injecting a single defect at the output of a multiplexer, considering all possible locations and input combinations. While at the interconnect level, fine grain redundancy is introduced which not only bypasses defects but also increases routability. Taking advantage of the sparse intra-cluster interconnect structures, routability is further improved by efficient distribution of feedback paths allowing more flexibility in the connections among logic blocks. Emulation results show a significant improvement of about 15% and 34% in the robustness of logic block and intra-cluster interconnect respectively. Furthermore, the impact of these hardening schemes on the testability of the FPGA cluster for manufacturing defects is also investigated in terms of maximum achievable fault coverage and the respective cost

Investigation into voltage and process variation-aware manufacturing test

Increasing integration and complexity in IC design provides challenges for manufacturing testing. This thesis studies how process and supply voltage variation influence defect behaviour to determine the impact on manufacturing test cost and quality. The focus is on logic testing of static CMOS designs with respect to two important defect types in deep submicron CMOS: resistive bridges and full opens. The first part of the thesis addresses testing for resistive bridge defects in designs with multiple supply voltage settings. To enable analysis, a fault simulator is developed using a supply voltage-aware model for bridge defect behaviour. The analysis shows that for high defect coverage it is necessary to perform test for more than one supply voltage setting, due to supply voltage-dependent behaviour. A low-cost and effective test method is presented consisting of multi-voltage test generation that achieves high defect coverage and test set size reduction without compromise to defect coverage. Experiments on synthesised benchmarks with realistic bridge locations validate the proposed method.The second part focuses on the behaviour of full open defects under supply voltage variation. The aim is to determine the appropriate value of supply voltage to use when testing. Two models are considered for the behaviour of full open defects with and without gate tunnelling leakage influence. Analysis of the supply voltage-dependent behaviour of full open defects is performed to determine if it is required to test using more than one supply voltage to detect all full open defects. Experiments on synthesised benchmarks using an extended version of the fault simulator tool mentioned above, measure the quantitative impact of supply voltage variation on defect coverage.The final part studies the impact of process variation on the behaviour of bridge defects. Detailed analysis using synthesised ISCAS benchmarks and realistic bridge model shows that process variation leads to additional faults. If process variation is not considered in test generation, the test will fail to detect some of these faults, which leads to test escapes. A novel metric to quantify the impact of process variation on test quality is employed in the development of a new test generation tool, which achieves high bridge defect coverage. The method achieves a user-specified test quality with test sets which are smaller than test sets generated without consideration of process variation

Optimizing Ram Testing Method For Test Time Saving Using Automatic Test Equipment

Due to the memory size increase drastically in the field programable gate array (FPGA) or system on chip (SOC) device, it become hard to meet the tests cost budget of the product especial for low-cost device. One of the major factor of test cost contributed is the test time. For the low-cost product, the tolerance number of the defects per million (DPM) are relative high compare to high cost product. By taking this advantage, an optimizing memory testing method able to implement to minimize the test time without jeopardize the test coverage. A memory Build-in Self-test (BIST) design with capability of algorithm failing sequence capture have been developed to implement in the Automate Test Equipment (ATE) flow for production screen. 3 selected algorithm have been tested on the 8 detect units in ATE flow to prove the concept of this method. The failing algorithm sequence of the units have been logged into database and analyzed for algorithm trimming. With the proper examples, the algorithm trimming location and test time saving calculation have been shown in this research. For this examples, approximate 33% of test time reduction observed for 1Kbyte memory testing with Hammer Head algorithm. In summary, this research has proposed the memory test time saving by optimizing the tests algorithm on the ATE flow

Design-for-delay-testability techniques for high-speed digital circuits

The importance of delay faults is enhanced by the ever increasing clock rates and decreasing geometry sizes of nowadays' circuits. This thesis focuses on the development of Design-for-Delay-Testability (DfDT) techniques for high-speed circuits and embedded cores. The rising costs of IC testing and in particular the costs of Automatic Test Equipment are major concerns for the semiconductor industry. To reverse the trend of rising testing costs, DfDT is\ud getting more and more important

Interconnect yield analysis and fault tolerance for field programmable gate arrays

Imperial Users onl