Multi-port Memory Design for Advanced Computer Architectures

In this thesis, we describe and evaluate novel memory designs for multi-port on-chip and off-chip use in advanced computer architectures. We focus on combining multi-porting and evaluating the performance over a range of design parameters. Multi-porting is essential for caches and shared-data systems, especially multi-core System-on-chips (SOC). It can significantly increase the memory access throughput. We evaluate FinFET voltage-mode multi-port SRAM cells using different metrics including leakage current, static noise margin and read/write performance. Simulation results show that single-ended multi-port FinFET SRAMs with isolated read ports offer improved read stability and flexibility over classical double-ended structures at the expense of write performance. By increasing the size of the access transistors, we show that the single-ended multi-port structures can achieve equivalent write performance to the classical double-ended multi-port structure for 9% area overhead. Moreover, compared with CMOS SRAM, FinFET SRAM has better stability and standby power. We also describe new methods for the design of FinFET current-mode multi-port SRAM cells. Current-mode SRAMs avoid the full-swing of the bitline, reducing dynamic power and access time. However, that comes at the cost of voltage drop, which compromises stability. The design proposed in this thesis utilizes the feature of Independent Gate (IG) mode FinFET, which can leverage threshold voltage by controlling the back gate voltage, to merge two transistors into one through high-Vt and low-Vt transistors. This design not only reduces the voltage drop, but it also reduces the area in multi-port current-mode SRAM design. For off-chip memory, we propose a novel two-port 1-read, 1-write (1R1W) phasechange memory (PCM) cell, which significantly reduces the probability of blocking at the bank levels. Different from the traditional PCM cell, the access transistors are at the top and connected to the bitline. We use Verilog-A to model the behavior of Ge2Sb2Te5 (GST: the storage component). We evaluate the performance of the two-port cell by transistor sizing and voltage pumping. Simulation results show that pMOS transistor is more practical than nMOS transistor as the access device when both area and power are considered. The estimated area overhead is 1.7�, compared to single-port PCM cell. In brief, the contribution we make in this thesis is that we propose and evaluate three different kinds of multi-port memories that are favorable for advanced computer architectures

Ultra Low Power Digital Circuit Design for Wireless Sensor Network Applications

Ny forskning innenfor feltet trådløse sensornettverk åpner for nye og innovative produkter og løsninger. Biomedisinske anvendelser er blant områdene med størst potensial og det investeres i dag betydelige beløp for å bruke denne teknologien for å gjøre medisinsk diagnostikk mer effektiv samtidig som man åpner for fjerndiagnostikk basert på trådløse sensornoder integrert i et ”helsenett”. Målet er å forbedre tjenestekvalitet og redusere kostnader samtidig som brukerne skal oppleve forbedret livskvalitet som følge av økt trygghet og mulighet for å tilbringe mest mulig tid i eget hjem og unngå unødvendige sykehusbesøk og innleggelser. For å gjøre dette til en realitet er man avhengige av sensorelektronikk som bruker minst mulig energi slik at man oppnår tilstrekkelig batterilevetid selv med veldig små batterier. I sin avhandling ” Ultra Low power Digital Circuit Design for Wireless Sensor Network Applications” har PhD-kandidat Farshad Moradi fokusert på nye løsninger innenfor konstruksjon av energigjerrig digital kretselektronikk. Avhandlingen presenterer nye løsninger både innenfor aritmetiske og kombinatoriske kretser, samtidig som den studerer nye statiske minneelementer (SRAM) og alternative minnearkitekturer. Den ser også på utfordringene som oppstår når silisiumteknologien nedskaleres i takt med mikroprosessorutviklingen og foreslår løsninger som bidrar til å gjøre kretsløsninger mer robuste og skalerbare i forhold til denne utviklingen. De viktigste konklusjonene av arbeidet er at man ved å introdusere nye konstruksjonsteknikker både er i stand til å redusere energiforbruket samtidig som robusthet og teknologiskalerbarhet øker. Forskningen har vært utført i samarbeid med Purdue University og vært finansiert av Norges Forskningsråd gjennom FRINATprosjektet ”Micropower Sensor Interface in Nanometer CMOS Technology”

Subthreshold SRAM Design for Energy Efficient Applications in Nanometric CMOS Technologies

Embedded SRAM circuits are vital components in a modern system on chip (SOC) that can occupy up to 90% of the total area. Therefore, SRAM circuits heavily affect SOC performance, reliability, and yield. In addition, most of the SRAM bitcells are in standby mode and significantly contribute to the total leakage current and leakage power consumption. The aggressive demand in portable devices and billions of connected sensor networks requires long battery life. Therefore, careful design of SRAM circuits with minimal power consumption is in high demand. Reducing the power consumption is mainly achieved by reducing the power supply voltage in the idle mode. However, simply reducing the supply voltage imposes practical limitations on SRAM circuits such as reduced static noise margin, poor write margin, reduced number of cells per bitline, and reduced bitline sensing margin that might cause read/write failures. In addition, the SRAM bitcell has contradictory requirements for read stability and writability. Improving the read stability can cause difficulties in a write operation or vice versa. In this thesis, various techniques for designing subthreshold energy-efficient SRAM circuits are proposed. The proposed techniques include improvement in read margin and write margin, speed improvement, energy consumption reduction, new bitcell architecture and utilizing programmable wordline boosting. A programmable wordline boosting technique is exploited on a conventional 6T SRAM bitcell to improve the operational speed. In addition, wordline boosting can reduce the supply voltage while maintaining the operational frequency. The reduction of the supply voltage allows the memory macro to operate with reduced power consumption. To verify the design, a 16-kb SRAM was fabricated using the TSMC 65 nm CMOS technology. Measurement results show that the maximum operational frequency increases up to 33.3% when wordline boosting is applied. Besides, the supply voltage can be reduced while maintaining the same frequency. This allows reducing the energy consumption to be reduced by 22.2%. The minimum energy consumption achieved is 0.536 fJ/b at 400 mV. Moreover, to improve the read margin, a 6T bitcell SRAM with a PMOS access transistor is proposed. Utilizing a PMOS access transistor results in lower zero level degradation, and hence higher read stability. In addition, the access transistor connected to the internal node holding V DD acts as a stabilizer and counterbalances the effect of zero level degradation. In order to improve the writability, wordline boosting is exploited. Wordline boosting also helps to compensate for the lower speed of the PMOS access transistor compared to a NMOS transistor. To verify our design, a 2kb SRAM is fabricated in the TSMC 65 nm CMOS technology. Measurement results show that the maximum operating frequency of the test chip is at 3.34 MHz at 290 mV. The minimum energy consumption is measured as 1.1 fJ/b at 400 mV

Modeling and Mitigation of Soft Errors in Nanoscale SRAMs

Energetic particle (alpha particle, cosmic neutron, etc.) induced single event data upset or soft error has emerged as a key reliability concern in SRAMs in sub-100 nanometre technologies. Low operating voltage, small node capacitance, high packing density, and lack of error masking mechanisms are primarily responsible for the soft error susceptibility of SRAMs. In addition, since SRAM occupies the majority of die area in system-on-chips (SoCs) and microprocessors, different leakage reduction techniques, such as, supply voltage reduction, gated grounding, etc., are applied to SRAMs in order to limit the overall chip leakage. These leakage reduction techniques exponentially increase the soft error rate in SRAMs. The soft error rate is further accentuated by process variations, which are prominent in scaled-down technologies. In this research, we address these concerns and propose techniques to characterize and mitigate soft errors in nanoscale SRAMs. We develop a comprehensive analytical model of the critical charge, which is a key to assessing the soft error susceptibility of SRAMs. The model is based on the dynamic behaviour of the cell and a simple decoupling technique for the non-linearly coupled storage nodes. The model describes the critical charge in terms of NMOS and PMOS transistor parameters, cell supply voltage, and noise current parameters. Consequently, it enables characterizing the spread of critical charge due to process induced variations in these parameters and to manufacturing defects, such as, resistive contacts or vias. In addition, the model can estimate the improvement in critical charge when MIM capacitors are added to the cell in order to improve the soft error robustness. The model is validated by SPICE simulations (90nm CMOS) and radiation test. The critical charge calculated by the model is in good agreement with SPICE simulations with a maximum discrepancy of less than 5%. The soft error rate estimated by the model for low voltage (sub 0.8 V) operations is within 10% of the soft error rate measured in the radiation test. Therefore, the model can serve as a reliable alternative to time consuming SPICE simulations for optimizing the critical charge and hence the soft error rate at the design stage. In order to limit the soft error rate further, we propose an area-efficient multiword based error correction code (MECC) scheme. The MECC scheme combines four 32 bit data words to form a composite 128 bit ECC word and uses an optimized 4-input transmission-gate XOR logic. Thus MECC significantly reduces the area overhead for check-bit storage and the delay penalty for error correction. In addition, MECC interleaves two composite words in a row for limiting cosmic neutron induced multi-bit errors. The ground potentials of the composite words are controlled to minimize leakage power without compromising the read data stability. However, use of composite words involves a unique write operation where one data word is written while other three data words are read to update the check-bits. A power efficient word line signaling technique is developed to facilitate the write operation. A 64 kb SRAM macro with MECC is designed and fabricated in a commercial 90nm CMOS technology. Measurement results show that the SRAM consumes 534 μW at 100 MHz with a data latency of 3.3 ns for a single bit error correction. This translates into 82% per-bit energy saving and 8x speed improvement over recently reported multiword ECC schemes. Accelerated neutron radiation test carried out at TRIUMF in Vancouver confirms that the proposed MECC scheme can correct up to 85% of soft errors

Dependable Embedded Systems

This Open Access book introduces readers to many new techniques for enhancing and optimizing reliability in embedded systems, which have emerged particularly within the last five years. This book introduces the most prominent reliability concerns from today’s points of view and roughly recapitulates the progress in the community so far. Unlike other books that focus on a single abstraction level such circuit level or system level alone, the focus of this book is to deal with the different reliability challenges across different levels starting from the physical level all the way to the system level (cross-layer approaches). The book aims at demonstrating how new hardware/software co-design solution can be proposed to ef-fectively mitigate reliability degradation such as transistor aging, processor variation, temperature effects, soft errors, etc. Provides readers with latest insights into novel, cross-layer methods and models with respect to dependability of embedded systems; Describes cross-layer approaches that can leverage reliability through techniques that are pro-actively designed with respect to techniques at other layers; Explains run-time adaptation and concepts/means of self-organization, in order to achieve error resiliency in complex, future many core systems