Programmable CMOS Analog-to-Digital Converter Design and Testability

In this work, a programmable second order oversampling CMOS delta-sigma analog-to-digital converter (ADC) design in 0.5µm n-well CMOS processes is presented for integration in sensor nodes for wireless sensor networks. The digital cascaded integrator comb (CIC) decimation filter is designed to operate at three different oversampling ratios of 16, 32 and 64 to give three different resolutions of 9, 12 and 14 bits, respectively which impact the power consumption of the sensor nodes. Since the major part of power consumed in the CIC decimator is by the integrators, an alternate design is introduced by inserting coder circuits and reusing the same integrators for different resolutions and oversampling ratios to reduce power consumption. The measured peak signal-to-noise ratio (SNR) for the designed second order delta-sigma modulator is 75.6dB at an oversampling ratio of 64, 62.3dB at an oversampling ratio of 32 and 45.3dB at an oversampling ratio of 16. The implementation of a built-in current sensor (BICS) which takes into account the increased background current of defect-free circuits and the effects of process variation on ΔIDDQ testing of CMOS data converters is also presented. The BICS uses frequency as the output for fault detection in CUT. A fault is detected when the output frequency deviates more than ±10% from the reference frequency. The output frequencies of the BICS for various model parameters are simulated to check for the effect of process variation on the frequency deviation. A design for on-chip testability of CMOS ADC by linear ramp histogram technique using synchronous counter as register in code detection unit (CDU) is also presented. A brief overview of the histogram technique, the formulae used to calculate the ADC parameters, the design implemented in 0.5µm n-well CMOS process, the results and effectiveness of the design are described. Registers in this design are replaced by 6T-SRAM cells and a hardware optimized on-chip testability of CMOS ADC by linear ramp histogram technique using 6T-SRAM as register in CDU is presented. The on-chip linear ramp histogram technique can be seamlessly combined with ΔIDDQ technique for improved testability, increased fault coverage and reliable operation

Studies on Core-Based Testing of System-on-Chips Using Functional Bus and Network-on-Chip Interconnects

The tests of a complex system such as a microprocessor-based system-onchip (SoC) or a network-on-chip (NoC) are difficult and expensive. In this thesis, we propose three core-based test methods that reuse the existing functional interconnects-a flat bus, hierarchical buses of multiprocessor SoC's (MPSoC), and a N oC-in order to avoid the silicon area cost of a dedicated test access mechanism (TAM). However, the use of functional interconnects as functional TAM's introduces several new problems. During tests, the interconnects-including the bus arbitrator, the bus bridges, and the NoC routers-operate in the functional mode to transport the test stimuli and responses, while the core under tests (CUT) operate in the test mode. Second, the test data is transported to the CUT through the functional bus, and not directly to the test port. Therefore, special core test wrappers that can provide the necessary control signals required by the different functional interconnect are proposed. We developed two types of wrappers, one buffer-based wrapper for the bus-based systems and another pair of complementary wrappers for the NoCbased systems. Using the core test wrappers, we propose test scheduling schemes for the three functionally different types of interconnects. The test scheduling scheme for a flat bus is developed based on an efficient packet scheduling scheme that minimizes both the buffer sizes and the test time under a power constraint. The schedulingscheme is then extended to take advantage of the hierarchical bus architecture of the MPSoC systems. The third test scheduling scheme based on the bandwidth sharing is developed specifically for the NoC-based systems. The test scheduling is performed under the objective of co-optimizing the wrapper area cost and the resulting test application time using the two complementary NoC wrappers. For each of the proposed methodology for the three types of SoC architec .. ture, we conducted a thorough experimental evaluation in order to verify their effectiveness compared to other methods

An asynchronous instruction length decoder

Journal ArticleAbstract-This paper describes an investigation of potential advantages and pitfalls of applying an asynchronous design methodology to an advanced microprocessor architecture. A prototype complex instruction set length decoding and steering unit was implemented using self-timed circuits. [The Revolving Asynchronous Pentium® Processor Instruction Decoder (RAPPID) design implemented the complete Pentium II® 32-bit MMX instruction set.] The prototype chip was fabricated on a 0.25-CMOS process and tested successfully. Results show significant advantages-in particular, performance of 2.5-4.5 instructions per nanosecond-with manageable risks using this design technology. The prototype achieves three times the throughput and half the latency, dissipating only half the power and requiring about the same area as the fastest commercial 400-MHz clocked circuit fabricated on the same process

Integration of a Digital Built-in Self-Test for On-Chip Memories

The ability of testing on-chip circuitry is extremely essential to ASIC implemen- tations today. However, providing functional tests and verification for on-chip (embedded) memories always poses a huge number of challenges to the designer. Therefore, a co-existing automated built-in self-test block with the Design Under Test (DUT) seems crucial to provide comprehensive, efficient and robust testing features. The target DUT of this thesis project is the state-of-the-arts Ultra Low Power (ULP) dual-port SRAMs designed in ASIC group of EIT department at Lund University. This thesis starts from system RTL modeling and verification from an earlier project, and then goes through ASIC design phase in 28 nm FD-SOI technology from ST-Microelectronics. All scripts during the ASIC design phase are developed in TCL. This design is implemented with multiple power domains (using CPF approach and introducing level-shifters at crossing-points between domains) and multiple clock sources in order to make it possible to perform various measurements with a high reliability on different flavours of a dual-port SRAM.This design is able to reduce dramatically the complexity of verification and measurement to integrated memories. This digital integrated circuit (IC) is developed as an application-specific IC (ASIC) chip for functional verification of integrated memories and measuring them in different aspects such as power consumption. The design is automated and capable of being reconfigured easily in terms of required actions and data for testing on-chip memories. Put it in other words, this design has automated and optimized the generation of what data to be stored on which location on memories as well as how they have been treated and interpreted later on. For instance, it refreshes and delivers different operation modes and working patterns to the entire test system in order to fully utilize integrated memories, of which such an automation is instructed by the stimuli to the chip. Besides, the pattern generation of the stimuli is implemented on MATLAB in an automated way. Due to constant advancements in chip manufacturing technology, more devices are squeezed into the same silicon area. Meaning that in order to monitor more internal signals introduced by the increased complexity of the circuits, more dedicated input/output ports (the physical interface between the chip internal signals and outside world) are required, that makes the chip bonding and testing in the future difficult and time-consuming. Additionally, memories usually have a bigger number of pins for signal reactions than other circuit blocks do, the method of dealing with so many pins should also be taken into account. Thus, a few techniques are adopted in this system to assist the designers deal with all mentioned issues. Once the ASIC chip has been fabricated (manufactured) and bonded, the on-chip memories can be tested directly on a printed circuit board in a simple and flexible way: Once test instruction input is loaded into the chip, the system starts to update the system settings and then to generate the internal configurations(parameters) so that all different operations, modes or instructions related to memory testing are automatically processed

Design-for-delay-testability techniques for high-speed digital circuits

The importance of delay faults is enhanced by the ever increasing clock rates and decreasing geometry sizes of nowadays' circuits. This thesis focuses on the development of Design-for-Delay-Testability (DfDT) techniques for high-speed circuits and embedded cores. The rising costs of IC testing and in particular the costs of Automatic Test Equipment are major concerns for the semiconductor industry. To reverse the trend of rising testing costs, DfDT is\ud getting more and more important