Architectural implementation of cordic unit and its applications

The ubiquity of DSP has made increasing demand to develop area efficient and accurate architectures in carrying out many nonlinear arithmetic operations. One such architecture is CORDIC unit which has many applications in the field of DSP including implementing transforms based on Fourier basis. This report presents architecture of CORDIC, embedded with a scaling unit that has only minimal number of adders and shifters. It can be implemented in rotation mode as well as vectoring mode. The purpose of the design is to get a scaling free CORDIC unit preserving the design of original algorithm. The proposed design has a considerable reduction in hardware when compared with other scaling free architectures. The analysis of error for different word lengths and different input ranges for fixed word length gives a better choice to choose the parameters. The error in rotation mode for 16 bit data path, obtained for Y equivalent input is 0.073% and for X equivalent input is 0.067%. We also report architecture of a DFT core that is implemented using low latency CORDIC. A scaling unit has been included to get scaled outputs. The reported DFT core architecture has 22 adders in total, in addition to 2 CORDIC units. DDS or NCO are nowadays prominently used in the applications of RF signal processing, satellite communications, etc. This report also brings out the FPGA implementation of one such DDS which has quadrature outputs. The proposed DDS design, which is based on pipelined CORDIC, has considerable improvement in terms of SFDR compared to other existing designs at reduced hardware. This report also proposes multiplier-less architecture for the implementation of radix-2^2 folded pipelined complex FFT core based on CORDIC technique. The number of points considered in the work is sixteen and the folding is done by a factor of four

A fast CORDIC co-processor architecture for digital signal processing applications

The coordinate rotational digital computer (CORDIC) is an arithmetic algorithm, which has been used for arithmetic units in the fast computing of elementary functions and for special purpose hardware in programmable logic devices. This paper describes a classification method that can be used for the possible applications of the algorithm and the architecture that is required for fast hardware computing of the algorithm.Área: Redes - Sistemas Operativos - Sistemas de Tiempo Real - Arquitectura de Procesadore

A fast CORDIC co-processor architecture for digital signal processing applications

The coordinate rotational digital computer (CORDIC) is an arithmetic algorithm, which has been used for arithmetic units in the fast computing of elementary functions and for special purpose hardware in programmable logic devices. This paper describes a classification method that can be used for the possible applications of the algorithm and the architecture that is required for fast hardware computing of the algorithm.Área: Redes - Sistemas Operativos - Sistemas de Tiempo Real - Arquitectura de ProcesadoresRed de Universidades con Carreras en Informática (RedUNCI

CALCULATION OF SINE AND COSINE OF AN ANGLE USING THE CORDIC ALGORITHM

With increasing on chip complexities the on chip area is a major concern. Today users desire every gadget to be small enough, particularly the hand held systems.CORDIC is one such algorithm which serves this purpose.CORDIC algorithm has become a widely used approach to elementary function evaluation when silicon area is a primary concern.CORDIC is more economical than DSP algorithms both in terms of area and power consumption.This paper presents how to calculate sine and cosine values of the given angle using CORDIC algorithm. Abrief description of the theory behind the algorithm is also given. Summary of CORDIC synthesis results based on Xilinx FPGAs is given. The system simulation was carried out using Xilinx ISE Design Suite13.1. The system is implemented using Virtex5 XC5VF70T FPGA  with Xilinx ISE12.1 and Verilog Hardware Description Language

Novel load identification techniques and a steady state self-tuning prototype for switching mode power supplies

Control of Switched Mode Power Supplies (SMPS) has been traditionally achieved through analog means with dedicated integrated circuits (ICs). However, as power systems are becoming increasingly complex, the classical concept of control has gradually evolved into the more general problem of power management, demanding functionalities that are hardly achievable in analog controllers. The high flexibility offered by digital controllers and their capability to implement sophisticated control strategies, together with the programmability of controller parameters, make digital control very attractive as an option for improving the features of dcdc converters. On the other side, digital controllers find their major weak point in the achievable dynamic performances of the closed loop system. Indeed, analogto-digital conversion times, computational delays and sampling-related delays strongly limit the small signal closed loop bandwidth of a digitally controlled SMPS. Quantization effects set other severe constraints not known to analog solutions. For these reasons, intensive scientific research activity is addressing the problem of making digital compensator stronger competitors against their analog counterparts in terms of achievable performances. In a wide range of applications, dcdc converters with high efficiency over the whole range of their load values are required. Integrated digital controllers for Switching Mode Power Supplies are gaining growing interest, since it has been shown the feasibility of digital controller ICs specifically developed for high frequency switching converters. One very interesting potential benefit is the use of autotuning of controller parameters (on-line controllers), so that the dynamic response can be set at the software level, independently of output capacitor filters, component variations and ageing. These kind of algorithms are able to identify the output filter configuration (system identification) and then automatically compute the best compensator gains to adjust system margins and bandwidth. In order to be an interesting solution, however, the self-tuning should satisfy two important requirements: it should not heavily affect converter operation under nominal condition and it should be based on a simple and robust algorithm whose complexity does not require a significant increase of the silicon area of the IC controller. The first issue is avoided performing the system identification (SI) with the system open loop configuration, where perturbations can be induced in the system before the start up. Much more challenging is to satisfy this requirement during steady state operations, where perturbations on the output voltage are limited by the regular operations of the converter. The main advantage of steady state SI methods, is the detection of possible non-idealities occurring during the converter operations. In this way, the system dynamics can be consequently adjusted with the compensator parameters tuning. The resource saving issue, requires the development of äd-hocßelf-tuning techniques specifically tailored for integrated digitally controlled converters. Considering the flexibility of digital control, self-tuning algorithms can be studied and easily integrated at hardware level into closed loop SMPS reducing development time and R & D costs. The work of this dissertation finds its origin in this context. Smart power management is accomplished by tuning the controller parameters accordingly to the identified converter configuration. Themain difficult for self-tuning techniques is the identification of the converter output filter configuration. Two novel system identification techniques have been validated in this dissertation. The open loop SI method is based on the system step response, while dithering amplification effects are exploited for the steady state SI method. The open loop method can be used as autotunig approach during or before the system start up, a step evolving reference voltage has been used as system perturbation and to obtain the output filter information with the Power Spectral Density (PSD) computation of the system step response. The use of ¢§ modulator is largely increasing in digital control feedback. During the steady state, the finite resolution introduces quantization effects on the signal path causing low frequency contributes of the digital control word. Through oversampling-dithering capabilities of ¢§ modulators, resolution improvements are obtained. The presented steady state identification techniques demonstrates that, amplifying the dithering effects on the signal path, the output filter information can be obtained on the digital side by processing with the PSD computation the perturbed output voltage. The amount of noise added on the output voltage does not affect the converter operations, mathematical considerations have been addressed and then justified both with a Matlab/Simulink fixed-point and a FPGA-based closed loop system. The load output filter identification of both algorithms, refer to the frequency domain. When the respective perturbations occurs, the system response is observed on the digital side and processed with the PSD computation. The extracted parameters are the resonant frequency ans the possible ESR (Effective Series Resistance) contributes,which can be detected as maximumin the PSD output. The SI methods have been validated for different configurations of buck converters on a fixed-point closed loop model, however, they can be easily applied to further converter configurations. The steady state method has been successfully integrated into a FPGA-based prototype for digitally controlled buck converters, that integrates a PSD computer needed for the load parameters identification. At this purpose, a novel VHDL-coded full-scalable hybrid processor for Constant Geometry FFT (CG-FFT) computation has been designed and integrated into the PSD computation system. The processor is based on a variation of the conventional algorithm used for FFT, which is the Constant-Geometry FFT (CG-FFT).Hybrid CORDIC-LUT scalable architectures, has been introduced as alternative approach for the twiddle factors (phase factors) computation needed during the FFT algorithms execution. The shared core architecture uses a single phase rotator to satisfy all TF requests. It can achieve improved logic saving by trading off with computational speed. The pipelined architecture is composed of a number of stages equal to the number of PEs and achieves the highest possible throughput, at the expense of more hardware usage

Signal processing architectures for automotive high-resolution MIMO radar systems

To date, the digital signal processing for an automotive radar sensor has been handled in an efficient way by general purpose signal processors and microcontrollers. However, increasing resolution requirements for automated driving on the one hand, as well as rapidly growing numbers of manufactured sensors on the other hand, can provoke a paradigm change in the near future. The design and development of highly specialized hardware accelerators could become a viable option - at least for the most demanding processing steps with data rates of several gigabits per second. In this work, application-specific signal processing architectures for future high-resolution multiple-input and multiple-output (MIMO) radar sensors are designed, implemented, investigated and optimized. A focus is set on real-time performance such that even sophisticated algorithms can be computed sufficiently fast. The full processing chain from the received baseband signals to a list of detections is considered, comprising three major steps: Spectrum analysis, target detection and direction of arrival estimation. The developed architectures are further implemented on a field-programmable gate array (FPGA) and important measurements like resource consumption, power dissipation or data throughput are evaluated and compared with other examples from literature. A substantial dataset, based on more than 3600 different parametrizations and variants, has been established with the help of a model-based design space exploration and is provided as part of this work. Finally, an experimental radar sensor has been built and is used under real-world conditions to verify the effectiveness of the proposed signal processing architectures.Bisher wurde die digitale Signalverarbeitung für automobile Radarsensoren auf eine effiziente Art und Weise von universell verwendbaren Mikroprozessoren bewältigt. Jedoch können steigende Anforderungen an das Auflösungsvermögen für hochautomatisiertes Fahren einerseits, sowie schnell wachsende Stückzahlen produzierter Sensoren andererseits, einen Paradigmenwechsel in naher Zukunft bewirken. Die Entwicklung von hochgradig spezialisierten Hardwarebeschleunigern könnte sich als eine praktikable Alternative etablieren - zumindest für die anspruchsvollsten Rechenschritte mit Datenraten von mehreren Gigabits pro Sekunde. In dieser Arbeit werden anwendungsspezifische Signalverarbeitungsarchitekturen für zukünftige, hochauflösende, MIMO Radarsensoren entworfen, realisiert, untersucht und optimiert. Der Fokus liegt dabei stets auf der Echtzeitfähigkeit, sodass selbst anspruchsvolle Algorithmen in einer ausreichend kurzen Zeit berechnet werden können. Die komplette Signalverarbeitungskette, beginnend von den empfangenen Signalen im Basisband bis hin zu einer Liste von Detektion, wird in dieser Arbeit behandelt. Die Kette gliedert sich im Wesentlichen in drei größere Teilschritte: Spektralanalyse, Zieldetektion und Winkelschätzung. Des Weiteren werden die entwickelten Architekturen auf einem FPGA implementiert und wichtige Kennzahlen wie Ressourcenverbrauch, Stromverbrauch oder Datendurchsatz ausgewertet und mit anderen Beispielen aus der Literatur verglichen. Ein umfangreicher Datensatz, welcher mehr als 3600 verschiedene Parametrisierungen und Varianten beinhaltet, wurde mit Hilfe einer modellbasierten Entwurfsraumexploration erstellt und ist in dieser Arbeit enthalten. Schließlich wurde ein experimenteller Radarsensor aufgebaut und dazu benutzt, die entworfenen Signalverarbeitungsarchitekturen unter realen Umgebungsbedingungen zu verifizieren

FPGA-Based Co-processor for Singular Value Array Reconciliation Tomography

This thesis describes a co-processor system that has been designed to accelerate computations associated with Singular Value Array Reconciliation Tomography (SART), a method for locating a wide-band RF source which may be positioned within an indoor environment, where RF propagation characteristics make source localization very challenging. The co-processor system is based on field programmable gate array (FPGA) technology, which offers a low-cost alternative to customized integrated circuits, while still providing the high performance, low power, and small size associated with a custom integrated solution. The system has been developed in VHDL, and implemented on a Virtex-4 SX55 FPGA development platform. The system is easy to use, and may be accessed through a C program or MATLAB script. Compared to a Pentium 4 CPU running at 3 GHz, use of the co-processor system provides a speed-up of about 6 times for the current signal matrix size of 128-by-16. Greater speed-ups may be obtained by using multiple devices in parallel. The system is capable of computing the SART metric to an accuracy of about -145 dB with respect to its true value. This level of accuracy, which is shown to be better than that obtained using single precision floating point arithmetic, allows even relatively weak signals to make a meaningful contribution to the final SART solution

Embedded electronic systems driven by run-time reconfigurable hardware

Abstract This doctoral thesis addresses the design of embedded electronic systems based on run-time reconfigurable hardware technology –available through SRAM-based FPGA/SoC devices– aimed at contributing to enhance the life quality of the human beings. This work does research on the conception of the system architecture and the reconfiguration engine that provides to the FPGA the capability of dynamic partial reconfiguration in order to synthesize, by means of hardware/software co-design, a given application partitioned in processing tasks which are multiplexed in time and space, optimizing thus its physical implementation –silicon area, processing time, complexity, flexibility, functional density, cost and power consumption– in comparison with other alternatives based on static hardware (MCU, DSP, GPU, ASSP, ASIC, etc.). The design flow of such technology is evaluated through the prototyping of several engineering applications (control systems, mathematical coprocessors, complex image processors, etc.), showing a high enough level of maturity for its exploitation in the industry.Resumen Esta tesis doctoral abarca el diseño de sistemas electrónicos embebidos basados en tecnología hardware dinámicamente reconfigurable –disponible a través de dispositivos lógicos programables SRAM FPGA/SoC– que contribuyan a la mejora de la calidad de vida de la sociedad. Se investiga la arquitectura del sistema y del motor de reconfiguración que proporcione a la FPGA la capacidad de reconfiguración dinámica parcial de sus recursos programables, con objeto de sintetizar, mediante codiseño hardware/software, una determinada aplicación particionada en tareas multiplexadas en tiempo y en espacio, optimizando así su implementación física –área de silicio, tiempo de procesado, complejidad, flexibilidad, densidad funcional, coste y potencia disipada– comparada con otras alternativas basadas en hardware estático (MCU, DSP, GPU, ASSP, ASIC, etc.). Se evalúa el flujo de diseño de dicha tecnología a través del prototipado de varias aplicaciones de ingeniería (sistemas de control, coprocesadores aritméticos, procesadores de imagen, etc.), evidenciando un nivel de madurez viable ya para su explotación en la industria.Resum Aquesta tesi doctoral està orientada al disseny de sistemes electrònics empotrats basats en tecnologia hardware dinàmicament reconfigurable –disponible mitjançant dispositius lògics programables SRAM FPGA/SoC– que contribueixin a la millora de la qualitat de vida de la societat. S’investiga l’arquitectura del sistema i del motor de reconfiguració que proporcioni a la FPGA la capacitat de reconfiguració dinàmica parcial dels seus recursos programables, amb l’objectiu de sintetitzar, mitjançant codisseny hardware/software, una determinada aplicació particionada en tasques multiplexades en temps i en espai, optimizant així la seva implementació física –àrea de silici, temps de processat, complexitat, flexibilitat, densitat funcional, cost i potència dissipada– comparada amb altres alternatives basades en hardware estàtic (MCU, DSP, GPU, ASSP, ASIC, etc.). S’evalúa el fluxe de disseny d’aquesta tecnologia a través del prototipat de varies aplicacions d’enginyeria (sistemes de control, coprocessadors aritmètics, processadors d’imatge, etc.), demostrant un nivell de maduresa viable ja per a la seva explotació a la indústria