Plasma deposition and surface modification techniques for wear resistance

The ion-assisted or plasma coating technology is discussed as it applies to the deposition of hard, wear resistant refractory compound films. Of the many sputtering and ion plating modes and configurations the reactive magnetron sputtering and the reactive triode ion plating techniques are the preferred ones to deposit wear resistant coatings for tribological applications. Both of these techniques incorporate additional means to enhance the ionization efficiency and chemical reaction to precision tailor desirable tribological characteristics. Interrelationships between film formation, structure, and ribological properties are strictly controlled by the deposition parameters and the substrate condition. The enhanced ionization contributes to the excellent adherence and coherence, reduced internal stresses and improved structural growth to form dense, cohesive, equiaxed grain structure for improved wear resistance and control

Overview of the JET results in support to ITER

The 2014–2016 JET results are reviewed in the light of their significance for optimising the ITER research plan for the active and non-active operation. More than 60 h of plasma operation with ITER first wall materials successfully took place since its installation in 2011. New multi-machine scaling of the type I-ELM divertor energy flux density to ITER is supported by first principle modelling. ITER relevant disruption experiments and first principle modelling are reported with a set of three disruption mitigation valves mimicking the ITER setup. Insights of the L–H power threshold in Deuterium and Hydrogen are given, stressing the importance of the magnetic configurations and the recent measurements of fine-scale structures in the edge radial electric. Dimensionless scans of the core and pedestal confinement provide new information to elucidate the importance of the first wall material on the fusion performance. H-mode plasmas at ITER triangularity (H = 1 at βN ~ 1.8 and n/nGW ~ 0.6) have been sustained at 2 MA during 5 s. The ITER neutronics codes have been validated on high performance experiments. Prospects for the coming D–T campaign and 14 MeV neutron calibration strategy are reviewed.European Commission (EUROfusion 633053

Overview of the JET preparation for deuterium-tritium operation with the ITER like-wall

For the past several years, the JET scientific programme (Pamela et al 2007 Fusion Eng. Des.82 590) has been engaged in a multi-campaign effort, including experiments in D, H and T, leading up to 2020 and the first experiments with 50%/50% D–T mixtures since 1997 and the first ever D–T plasmas with the ITER mix of plasma-facing component materials. For this purpose, a concerted physics and technology programme was launched with a view to prepare the D–T campaign (DTE2). This paper addresses the key elements developed by the JET programme directly contributing to the D–T preparation. This intense preparation includes the review of the physics basis for the D–T operational scenarios, including the fusion power predictions through first principle and integrated modelling, and the impact of isotopes in the operation and physics of D–T plasmas (thermal and particle transport, high confinement mode (H-mode) access, Be and W erosion, fuel recovery, etc). This effort also requires improving several aspects of plasma operation for DTE2, such as real time control schemes, heat load control, disruption avoidance and a mitigation system (including the installation of a new shattered pellet injector), novel ion cyclotron resonance heating schemes (such as the three-ions scheme), new diagnostics (neutron camera and spectrometer, active Alfvèn eigenmode antennas, neutral gauges, radiation hard imaging systems...) and the calibration of the JET neutron diagnostics at 14 MeV for accurate fusion power measurement. The active preparation of JET for the 2020 D–T campaign provides an incomparable source of information and a basis for the future D–T operation of ITER, and it is also foreseen that a large number of key physics issues will be addressed in support of burning plasmas.This work has been carried out within the framework of the EUROfusion Consortium and has received funding from the Euratom research and training programme 2014–2018 and 2019–2020 under grant agreement No. 633053Postprint (published version

Study on physio-chemical properties of plasma polymerization in C2H2/N2 plasma and their impact on COL X

Nitrogen-containing plasma polymerization is of considerable interest for tissue engineering due to their properties on cell adhesion and mesenchymal stem cells (MSCs) response. In this study, low-pressure RF plasma of acetylene and nitrogen was used to deposit nitrogen-containing plasma polymerized coatings on several substrates. Deposition kinetics and surface characteristics of coatings were investigated in terms of RF power and gas flow ratio. OES was used to monitor the plasma process and investigate the relation between the film structure and plasma species. Presence of several bonds and low concentration of amine functional groups were determined using FTIR and Colorimetric methods. Contact angle goniometry results indicated about 30% increase in surface hydrophilicity. Stability of coatings in air and two different liquid environments was examined by repeating surface free energy measurements. Deposited films exhibited acceptable stability during the storage duration. Surface roughness measured by AFM was found to decrease with growing concentration of nitrogen. The deposition rate increased with increasing RF power and decreased with growing concentration of nitrogen. Zeta potential measurements of coatings revealed the negative potential on the surface of the thin films. Temporary suppression of collagen X in the presence of plasma coatings was confirmed by RT-PCR results

Analysis of glow discharges for understanding the process of film formation

The physical and chemical processes which occur during the formation of different types of films in a variety of glow discharge plasmas are discussed. Emphasis is placed on plasma diagnostic experiments using spectroscopic methods, probe analysis, mass spectrometric sampling and magnetic resonance techniques which are well suited to investigate the neutral and ionized gas phase species as well as some aspects of plasma surface interactions. The results on metallic, semi-conducting and insulating films are reviewed in conjunction with proposed models and the problem encountered under film deposition conditions. It is concluded that the understanding of film deposition process requires additional experimental information on plasma surface interactions of free radicals and the synergetic effects where photon, electron and ion bombardment change the reactivity of the incident radical with the surface

Recent work on an RF ion thruster

An experimental investigation of an rf ion thruster using an immersed coupler in an argon discharge is reported. The conical coil, used to couple rf power into the discharge, is placed inside the discharge vessel. The discharge was self-sustained by 100-150 MHz rf power at low environmental pressures. The ion extraction was accomplished by conventional accelerated grid optics from an unoptimized 8 cm diameter ion thruster

High-pressure micro-discharges in etching and deposition applications

High-pressure micro-discharges are promising sources of light, ions, and radicals and offer some advantages in materials processing applications as compared to other more conventional discharges. We review here results from etching experiments using stencil masks where the discharge is formed only in the pattern cutout. The mask consists of a thin metal-dielectric structure and is pressed against a Si wafer, which becomes part of the electric circuit. Pattern transfer takes place, albeit the profile shape appears to be limited by the expansion of the plasma into the etched hole at long etch times. We also review experiments on using micro-discharges as sources of radicals for materials deposition applications. In the latter case, the micro-discharges form in metal capillary tubes permitting incorporation of gas flow and a short reaction zone that can be controlled to favour production of specific radicals. We demonstrate these concepts by using CH4/H2 chemistry for diamond deposition on a heated Mo substrate. Good quality micro- and nano-diamond crystals could be produced