Tribological And Dynamical Study Of An Automotive Transmission System

The transmission system is critical for automotive and heavy duty equipment due to its prominent role in the powertrain system, which is often challenged with degraded torque capacity and harsh dynamic response. Simulation-guided design can provide appropriate guidelines to resolve these problems with virtual analyses. In current study, the tribological and dynamical study of an automatic transmission is performed at two levels: a wet clutch and powertrain. In this dissertation, tribological study is performed for a wet clutch based on the thermohydrodynamic (THD) analysis that takes the following factors into account. • The groove effect (depth, area, and pattern) is investigated for lubrication analysis; • The elastic-plastic asperity contact model is used to predict the contact pressure; • The heat transfer during the entire cycle of engagement from slip to lock to detachment is covered; • The engagement time and the temperature profile are predicted for torque and thermal analysis. With large engagement cycles, the friction lining of a wet clutch is worn off due to the material degradation at high load/temperature condition. By relating the wear behavior with the mechanism of thermal degradation and thermomechanical degradation, a physics-based wear model is proposed for the first time to analyze the wear process in a wet clutch. The predicted wear rate falls within nearly 95% confidence interval of the test results. Discrepancies of simulation are primarily due to limited availability of input data and model assumptions. Therefore, an uncertainty quantification analysis of the wear model is performed using the Monte Carlo simulations. In addition, a comprehensive parametric analysis of the clutch wear is considered with various factors, including groove design (waffle pattern shows the minimum wear), material properties and operational configurations (rotational speed plays the most influential role). The dynamics of transmission directly affects the performance of the powertrain. The coupling effects of the key transmission components are examined. Of particular interests are the stick-slip behavior of the wet clutch and backlash of the gear train. Through simulation of the powertrain, the main source and the pattern of vibration propagation in the driveline are examined. Major vibration is observed during inappropriate clutch engagement

Vibration, Control and Stability of Dynamical Systems

From Preface: This is the fourteenth time when the conference “Dynamical Systems: Theory and Applications” gathers a numerous group of outstanding scientists and engineers, who deal with widely understood problems of theoretical and applied dynamics. Organization of the conference would not have been possible without a great effort of the staff of the Department of Automation, Biomechanics and Mechatronics. The patronage over the conference has been taken by the Committee of Mechanics of the Polish Academy of Sciences and Ministry of Science and Higher Education of Poland. It is a great pleasure that our invitation has been accepted by recording in the history of our conference number of people, including good colleagues and friends as well as a large group of researchers and scientists, who decided to participate in the conference for the first time. With proud and satisfaction we welcomed over 180 persons from 31 countries all over the world. They decided to share the results of their research and many years experiences in a discipline of dynamical systems by submitting many very interesting papers. This year, the DSTA Conference Proceedings were split into three volumes entitled “Dynamical Systems” with respective subtitles: Vibration, Control and Stability of Dynamical Systems; Mathematical and Numerical Aspects of Dynamical System Analysis and Engineering Dynamics and Life Sciences. Additionally, there will be also published two volumes of Springer Proceedings in Mathematics and Statistics entitled “Dynamical Systems in Theoretical Perspective” and “Dynamical Systems in Applications”

Investigation of all-wheel-drive off-road vehicle dynamics augmented by visco-lock devices

A peculiarity of AWD off-road vehicles is that their behaviour depends not only on the total power, provided by the engine, but also on its distribution among the drive axles/wheels. In turn, this distribution is largely regulated by the drivetrain layout and its torque distribution devices. At the output of the drivetrain system, the torque is constrained by the interaction between the wheels and the soft soil. For off-road automotive applications, the design of drivetrain systems has usually been largely dominated by the mobility requirements. With the growing demand to have a multipurpose on/off road vehicle with improved manoeuvrability over deformable soil, particularly at higher speed, the challenges confronting vehicle designers have become more complex. The thesis presents a novel integrated numerical approach to assess the dynamic behaviour of all-wheel-drive vehicles whilst operating over deformable soil terrain. [Continues.

Mechanical Engineering

The book substantially offers the latest progresses about the important topics of the "Mechanical Engineering" to readers. It includes twenty-eight excellent studies prepared using state-of-art methodologies by professional researchers from different countries. The sections in the book comprise of the following titles: power transmission system, manufacturing processes and system analysis, thermo-fluid systems, simulations and computer applications, and new approaches in mechanical engineering education and organization systems

Safety Assessment of Road Vehicle in Crosswind Considering Driver Behavior

With expansion of the economy, more and more highway networks extend to coastal areas and mountain valley areas. Vehicles will be exposed to strong crosswinds when driven on these highway roads, especially in hurricane season and in winter in these two different topographic areas. Strong crosswinds threaten the safety of transportation infrastructure and passing vehicles in forms of vehicle accidents that usually result in traffic blockage and driver injury, posing negative effects on economic growth. This dissertation aimed to evaluate the vehicle safety when running through crosswinds in consideration of driver behaviors. Firstly, the aerodynamic characteristics of road vehicles were identified using computational fluid dynamic method. Aerodynamic coefficients of a high-side lorry running in crosswinds using both traditional resultant-wind velocity method and relative-motion approach were compared. In addition, the aerodynamic coefficients of multiple types of vehicles were investigated. The curves of aerodynamic coefficients for different vehicle types against wind yaw angles were obtained. Secondly, an experimental investigation on the vehicle performance and driver behavior was conducted by taking advantage of the LSU’s driving simulator. This study revealed the repeatability of driver behavior and the effect of crosswind speeds on the vehicle performance and drivers’ behavior through a statistical analysis. More scenarios were considered, such as driving in windy-rainy conditions. A regression model of the steering wheel angle turned by drivers was obtained. Finally, safety assessment of vehicles was performed based on an improved wind-vehicle-bridge coupled system and considering driver’s behavior using a series of driver behavior models. For different types of road vehicles, rigid frame vehicle model and flexible frame vehicle model were developed. Accident criteria of lateral side slip, rotational deviation, and rollover were considered. To investigate the influence of driver models, four driver models were considered in different integration methods. Results between cases from different driver models were compared

Aeronautical Engineering: A continuing bibliography with indexes, supplement 137, July 1981

This bibliography lists 483 reports, articles, and other documents introduced into the NASA scientific and technical information system in June 1981

Experimental Aerothermal Performance of Turbofan Bypass Flow Heat Exchangers

The path to future aero-engines with more efficient engine architectures requires advanced thermal management technologies to handle the demand of refrigeration and lubrication. Oil systems, holding a double function as lubricant and coolant circuits, require supplemental cooling sources to the conventional fuel based cooling systems as the current oil thermal capacity becomes saturated with future engine developments. The present research focuses on air/oil coolers, which geometrical characteristics and location are designed to minimize aerodynamic effects while maximizing the thermal exchange. The heat exchangers composed of parallel fins are integrated at the inner wall of the secondary duct of a turbofan. The analysis of the interaction between the three-dimensional high velocity bypass flow and the heat exchangers is essential to evaluate and optimize the aero-thermodynamic performances, and to provide data for engine modeling. The objectives of this research are the development of engine testing methods alternative to flight testing, and the characterization of the aerothermal behavior of different finned heat exchanger configurations. A new blow-down wind tunnel test facility was specifically designed to replicate the engine bypass flow in the region of the splitter. The annular sector type test section consists on a complex 3D geometry, as a result of three dimensional numerical flow simulations. The flow evolves over the splitter duplicated at real scale, guided by helicoidally shaped lateral walls. The development of measurement techniques for the present application involved the design of instrumentation, testing procedures and data reduction methods. Detailed studies were focused on multi-hole and fine wire thermocouple probes. Two types of test campaigns were performed dedicated to: flow measurements along the test section for different test configurations, i.e. in the absence of heat exchangers and in the presence of different heat exchanger geometries, and heat transfer measurements on the heat exchanger. As a result contours of flow velocity, angular distributions, total and static pressures, temperatures and turbulence intensities, at different bypass duct axial positions, as well as wall pressures along the test section, were obtained. The analysis of the flow development along the test section allowed the understanding of the different flow behaviors for each test configuration. Comparison of flow variables at each measurement plane permitted quantifying and contrasting the different flow disturbances. Detailed analyses of the flow downstream of the heat exchangers were assessed to characterize the flow in the fins¿ wake region. The aerodynamic performance of each heat exchanger configuration was evaluated in terms of non dimensional pressure losses. Fins convective heat transfer characteristics were derived from the infrared fin surface temperature measurements through a new methodology based on inverse heat transfer methods coupled with conductive heat flux models. The experimental characterization permitted to evaluate the cooling capacity of the investigated type of heat exchangers for the design operational conditions. Finally, the thermal efficiency of the heat exchanger at different points of the flight envelope during a typical commercial mission was estimated by extrapolating the convective properties of the flow to flight conditions.Villafañe Roca, L. (2013). Experimental Aerothermal Performance of Turbofan Bypass Flow Heat Exchangers [Tesis doctoral no publicada]. Universitat Politècnica de València. https://doi.org/10.4995/Thesis/10251/34774TESI

Aeronautical Engineering: A continuing bibliography with indexes, supplement 106

This bibliography lists 388 reports, articles, and other documents introduced into the NASA scientific and technical information system in January 1979

Aeronautical Engineering: A continuing bibliography with indexes (supplement 188)

This bibliography lists 477 reports, articles and other documents introduced into the NASA scientific and technical information system in May 1985. The coverage includes documents on the engineering and theoretical aspects of design, construction, evaluation, testing, operation, and performance of aircraft (including aircraft engines) and associated components, equipment and systems

Aeronautical engineering: A continuing bibliography with indexes (supplement 289)

This bibliography lists 792 reports, articles, and other documents introduced into the NASA scientific and technical information system in Mar. 1993. Subject coverage includes: design, construction and testing of aircraft and aircraft engines; aircraft components, equipment, and systems; ground support systems; and theoretical and applied aspects of aerodynamics and general fluid dynamics