Optimization of the interoperability and dynamic spectrum management in mobile communications systems beyond 3G

The future wireless ecosystem will heterogeneously integrate a number of overlapped Radio Access Technologies (RATs) through a common platform. A major challenge arising from the heterogeneous network is the Radio Resource Management (RRM) strategy. A Common RRM (CRRM) module is needed in order to provide a step toward network convergence. This work aims at implementing HSDPA and IEEE 802.11e CRRM evaluation tools. Innovative enhancements to IEEE 802.11e have been pursued on the application of cross-layer signaling to improve Quality of Service (QoS) delivery, and provide more efficient usage of radio resources by adapting such parameters as arbitrary interframe spacing, a differentiated backoff procedure and transmission opportunities, as well as acknowledgment policies (where the most advised block size was found to be 12). Besides, the proposed cross-layer algorithm dynamically changes the size of the Arbitration Interframe Space (AIFS) and the Contention Window (CW) duration according to a periodically obtained fairness measure based on the Signal to Interference-plus-Noise Ratio (SINR) and transmission time, a delay constraint and the collision rate of a given machine. The throughput was increased in 2 Mb/s for all the values of the load that have been tested whilst satisfying more users than with the original standard. For the ad hoc mode an analytical model was proposed that allows for investigating collision free communications in a distributed environment. The addition of extra frequency spectrum bands and an integrated CRRM that enables spectrum aggregation was also addressed. RAT selection algorithms allow for determining the gains obtained by using WiFi as a backup network for HSDPA. The proposed RAT selection algorithm is based on the load of each system, without the need for a complex management system. Simulation results show that, in such scenario, for high system loads, exploiting localization while applying load suitability optimization based algorithm, can provide a marginal gain of up to 450 kb/s in the goodput. HSDPA was also studied in the context of cognitive radio, by considering two co-located BSs operating at different frequencies (in the 2 and 5 GHz bands) in the same cell. The system automatically chooses the frequency to serve each user with an optimal General Multi-Band Scheduling (GMBS) algorithm. It was shown that enabling the access to a secondary band, by using the proposed Integrated CRRM (iCRRM), an almost constant gain near 30 % was obtained in the throughput with the proposed optimal solution, compared to a system where users are first allocated in one of the two bands and later not able to handover between the bands. In this context, future cognitive radio scenarios where IEEE 802.11e ad hoc modes will be essential for giving access to the mobile users have been proposed

Design and optimization of QoS-based medium access control protocols for next-generation wireless LANs

This thesis was submitted for the degree of Doctor of Philosophy and awarded by Brunel University.In recent years, there have been tremendous advances in wireless & mobile communications, including wireless radio techniques, networking protocols, and mobile devices. It is expected that different broadband wireless access technologies, e.g., WiFi (IEEE 802.11) and WiMAX (IEEE 802.16) will coexist in the future. In the meantime, multimedia applications have experienced an explosive growth with increasing user demands. Nowadays, people expect to receive high-speed video, audio, voice and web services even when being mobile. The key question that needs to be answered, then, is how do we ensure that users always have the "best" network performance with the "lowest" costs in such complicated situations? The latest IEEE 802.11n standards attains rates of more than 100 Mbps by introducing innovative enhancements at the PHY and MAC layer, e.g. MIMO and Frame Aggregation, respectively. However, in this thesis we demonstrate that frame aggregation's performance adheres due to the EDCA scheduler's priority mechanism and consequently resulting in the network's poor overall performance. Short waiting times for high priority flows into the aggregation queue resolves to poor channel utilization. A Delayed Channel Access algorithm was designed to intentionally postpone the channel access procedure so that the number of packets in a formed frame can be increased and so will the network's overall performance. However, in some cases, the DCA algorithm has a negative impact on the applications that utilize the TCP protocol, especially the when small TCP window sizes are engaged. So, the TCP process starts to refrain from sending data due to delayed acknowledgements and the overall throughput drops. In this thesis, we address the above issues by firstly demonstrating the potential performance benefits of frame aggregation over the next generation wireless networks. The efficiency and behaviour of frame aggregation within a single queue, are mathematically analysed with the aid of a M=G[a;b]=1=K model. Results show that a trade-off choice has to be taken into account over minimizing the waiting time or maximizing utilization. We also point out that there isn't an optimum batch collection rule which can be assumed as generally valid but individual cases have to be considered separately. Secondly, we demonstrate through extensive simulations that by introducing a method, the DCA algorithm, which dynamically determines and adapts batch collections based upon the traffic's characteristics, QoS requirements and server's maximum capacity, also improves e ciency. Thirdly, it is important to understand the behaviour of the TCP ows over the WLAN and the influence that DCA has over the degrading performance of the TCP protocol. We investigate the cause of the problem and provide the foundations of designing and implementing possible solutions. Fourthly, we introduce two innovative proposals, one amendment and one extension to the original DCA algorithm, called Adaptive DCA and Selective DCA, respectively. Both solutions have been implemented in OPNET and extensive simulation runs over a wide set of scenarios show their effectiveness over the network's overall performance, each in its own way.This study was supported by the Engineering and Physical Sciences Research Council (EPSRC)

Cooperative communication in wireless local area networks

The concept of cooperative communication has been proposed to improve link capacity, transmission reliability and network coverage in multiuser wireless communication networks. Different from conventional point-to-point and point-to-multipoint communications, cooperative communication allows multiple users or stations in a wireless network to coordinate their packet transmissions and share each other’s resources, thus achieving high performance gain and better service coverage. According to the IEEE 802.11 standards, Wireless Local Area Networks (WLANs) can support multiple transmission data rates, depending on the instantaneous channel condition between a source station and an Access Point (AP). In such a multi-rate WLAN, those low data-rate stations will occupy the shared communication channel for a longer period for transmitting a fixed-size packet to the AP, thus reducing the channel efficiency and overall system performance. This thesis addresses this challenging problem in multi-rate WLANs by proposing two cooperative Medium Access Control (MAC) protocols, namely Busy Tone based Cooperative MAC (BTAC) protocol and Cooperative Access with Relay’s Data (CARD) protocol. Under BTAC, a low data-rate sending station tries to identify and use a close-by intermediate station as its relay to forward its data packets at higher data-rate to the AP through a two-hop path. In this way, BTAC can achieve cooperative diversity gain in multi-rate WLANs. Furthermore, the proposed CARD protocol enables a relay station to transmit its own data packets to the AP immediately after forwarding its neighbour’s packets, thus minimising the handshake procedure and overheads for sensing and reserving the common channel. In doing so, CARD can achieve both cooperative diversity gain and cooperative multiplexing gain. Both BTAC and CARD protocols are backward compatible with the existing IEEE 802.11 standards. New cross-layer mathematical models have been developed in this thesis to study the performance of BTAC and CARD under different channel conditions and for saturated and unsaturated traffic loads. Detailed simulation platforms were developed and are discussed in this thesis. Extensive simulation results validate the mathematical models developed and show that BTAC and CARD protocols can significantly improve system throughput, service delay, and energy efficiency for WLANs operating under realistic communication scenarios

Final report on the evaluation of RRM/CRRM algorithms

Deliverable public del projecte EVERESTThis deliverable provides a definition and a complete evaluation of the RRM/CRRM algorithms selected in D11 and D15, and evolved and refined on an iterative process. The evaluation will be carried out by means of simulations using the simulators provided at D07, and D14.Preprin

Cross-layer design and optimization of medium access control protocols for wlans

This thesis provides a contribution to the field of Medium Access Control (MAC) layer protocol design for wireless networks by proposing and evaluating mechanisms that enhance different aspects of the network performance. These enhancements are achieved through the exchange of information between different layers of the traditional protocol stack, a concept known as Cross-Layer (CL) design. The main thesis contributions are divided into two parts. The first part of the thesis introduces a novel MAC layer protocol named Distributed Queuing Collision Avoidance (DQCA). DQCA behaves as a reservation scheme that ensures collision-free data transmissions at the majority of the time and switches automatically to an Aloha-like random access mechanism when the traffic load is low. DQCA can be enriched by more advanced scheduling algorithms based on a CL dialogue between the MAC and other protocol layers, to provide higher throughput and Quality of Service (QoS) guarantees. The second part of the thesis explores a different challenge in MAC layer design, related to the ability of multiple antenna systems to offer point-to-multipoint communications. Some modifications to the recently approved IEEE 802.11n standard are proposed in order to handle simultaneous multiuser downlink transmissions. A number of multiuser MAC schemes that handle channel access and scheduling issues and provide mechanisms for feedback acquisition have been presented and evaluated. The obtained performance enhancements have been demonstrated with the help of both theoretical analysis and simulation obtained results

Towards the Quality of Service for VoIP traffic in IEEE 802.11 Wireless Networks

The usage of voice over IP (VoIP) traffic in IEEE 802.11 wireless networks is expected to increase in the near future due to widely deployed 802.11 wireless networks and VoIP services on fixed lines. However, the quality of service (QoS) of VoIP traffic in wireless networks is still unsatisfactory. In this thesis, I identify several sources for the QoS problems of VoIP traffic in IEEE 802.11 wireless networks and propose solutions for these problems. The QoS problems discussed can be divided into three categories, namely, user mobility, VoIP capacity, and call admission control. User mobility causes network disruptions during handoffs. In order to reduce the handoff time between Access Points (APs), I propose a new handoff algorithm, Selective Scanning and Caching, which finds available APs by scanning a minimum number of channels and furthermore allows clients to perform handoffs without scanning, by caching AP information. I also describe a new architecture for the client and server side for seamless IP layer handoffs, which are caused when mobile clients change the subnet due to layer 2 handoffs. I also present two methods to improve VoIP capacity for 802.11 networks, Adaptive Priority Control (APC) and Dynamic Point Coordination Function (DPCF). APC is a new packet scheduling algorithm at the AP and improves the capacity by balancing the uplink and downlink delay of VoIP traffic, and DPCF uses a polling based protocol and minimizes the bandwidth wasted from unnecessary polling, using a dynamic polling list. Additionally, I estimated the capacity for VoIP traffic in IEEE 802.11 wireless networks via theoretical analysis, simulations, and experiments in a wireless test-bed and show how to avoid mistakes in the measurements and comparisons. Finally, to protect the QoS for existing VoIP calls while maximizing the channel utilization, I propose a novel admission control algorithm called QP-CAT (Queue size Prediction using Computation of Additional Transmission), which accurately predicts the impact of new voice calls by virtually transmitting virtual new VoIP traffic

Control-theoretic adaptive mechanisms for performance optimization of IEEE 802.11 WLANs: design, implementation and experimental evaluation

The media access control (MAC) layer of the IEEE 802.11 standard specifies a set of parameters that regulate the behavior of the wireless stations when accessing the channel. Although the standard defines a set of recommended values for these parameters, they are statically set and do not take into account the current conditions in the wireless local area network (WLAN) in terms of, e.g., number of contending stations and the traffic they generate, which results in suboptimal performance. In this thesis we propose two novel control theoretic approaches to optimally configure the WLAN parameters based on the dynamically observed network conditions: a Centralized Adaptive Control (CAC) algorithm, whereby the access point (AP) computes the con guration that maximizes performance and signals it to the active stations, and a Distributed Adaptive Control (DAC) algorithm, which is independently employed by each station with the same goal. In contrast to previous proposals, which are mostly based on heuristics, our approaches build upon (i) analytical models of the WLAN performance, used to derive the optimal point of operation of the IEEE 802.11 protocol, and (ii) mathematical foundations from single- and multi-variable control theory, used to design the mechanisms that drive the WLAN to this point of operation. Another key advantage of the proposed algorithms over existing approaches is that they are compliant with the IEEE 802.11 standard and can be implemented with current wireless cards without introducing any modifications into their hardware and/or firmware. We show by means of an exhaustive performance evaluation study that our algorithms maximize the WLAN performance in terms of throughput and delay under a wide set of network conditions, substantially outperforming the standard recommended configuration as well as previous adaptive proposals. Finally, we present our experiences with implementing the proposed adaptive algorithms in a real IEEE 802.11 testbed and discuss the implementation details of the building blocks that comprise these mechanisms. We evaluate their performance by conducting extensive measurements, considering different network conditions in terms of number of nodes, transmission power employed and tra c generated. Based on the obtained results, we provide valuable insights on the performance of the distributed and centralized algorithms and discuss the suitability of these schemes for real deployments. ------------------------------------------------------------------------------------------------------------------------------------------------------------------------El nivel MAC (Media Access Control) del estándar IEEE 802.11 especifica una serie de parámetros que definen el comportamiento de las estaciones inalámbricas cuando acceden al canal. En dicho estándar se define un conjunto de valores recomendados para estos parámetros, si bien estos valores, constantes, no tienen en cuenta las condiciones de la red inalámbrica -en términos de, por ejemplo, número de estaciones o tráfico cursado- por lo que resultan en un rendimiento subóptimo. En esta tesis se proponen dos nuevos algoritmos para configurar de forma óptima estos parámetros partiendo de las condiciones observadas de la red. Dichos algoritmos, construidos sobre la base de la teoría de control, son los siguientes: CAC (Centralized Adaptive Control), que se ejecuta en el punto de acceso, el cual distribuye la configuración a usar al resto de estaciones; y DAC (Distributed Adaptive Control), ejecutado por cada estación de la red inalámbrica de forma independiente. A diferencia de las propuestas anteriores, casi todas ellas basada en heurísticos, los algoritmos se basan en (i) un modelo analítico del rendimiento de la red inalámbrica, necesario para obtener el punto de operación óptimo de la red; y (ii) fundamentos matemáticos de la teoría de control mono y multivariable, aplicados para diseñar el mecanismo que lleva la red a dicho punto de operación. Otra ventaja de los esquemas propuestos frente al trabajo previo es que son compatibles con el estándar IEEE 802.11, y pueden ser implementados sobre las tarjetas existentes sin necesidad de cambiar el hardware o el firmware. Mediante una extensa evaluación de rendimiento bajo diversas condiciones, se comprueba que los algoritmos maximizan las prestaciones de la red tanto en ancho de banda como en retardo, mejorando notablemente los resultados proporcionados por la configuración recomendada en el estándar así como por propuestas dinámicas anteriores. Por último, se presentan las experiencias del prototipado de dichos algoritmos sobre dispositivos IEEE 802.11, discutiendo los detalles de implementación de sus diferentes bloques. Se evalúan las prestaciones de los mismos mediante una extensa serie de experimentos, incluyendo diferentes escenarios en términos del número de nodos, potencia de transmisión usada y tráfico generado. Los resultados obtenidos permiten extraer valiosas conclusiones sobre el rendimiento de los esquemas adaptativos centralizados y distribuidos, así como la viabilidad de su despliegue en escenarios reales

Contributions to IEEE 802.11-based long range communications

The most essential part of the Internet of Things (IoT) infrastructure is the wireless communication system that acts as a bridge for the delivery of data and control messages between the connected things and the Internet. Since the conception of the IoT, a large number of promising applications and technologies have been developed, which will change different aspects in our daily life. However, the existing wireless technologies lack the ability to support a huge amount of data exchange from many battery-driven devices, spread over a wide area. In order to support the IoT paradigm, IEEE 802.11ah is an Internet of Things enabling technology, where the efficient management of thousands of devices is a key function. This is one of the most promising and appealing standards, which aims to bridge the gap between traditional mobile networks and the demands of the IoT. To this aim, IEEE 802.11ah provides the Restricted Access Window (RAW) mechanism, which reduces contention by enabling transmissions for small groups of stations. Optimal grouping of RAW stations requires an evaluation of many possible configurations. In this thesis, we first discuss the main PHY and MAC layer amendments proposed for IEEE 802.11ah. Furthermore, we investigate the operability of IEEE 802.11ah as a backhaul link to connect devices over possibly long distances. Additionally, we compare the aforementioned standard with previous notable IEEE 802.11 amendments (i.e. IEEE 802.11n and IEEE 802.11ac) in terms of throughput (with and without frame aggregation) by utilizing the most robust modulation schemes. The results show an improved performance of IEEE 802.11ah (in terms of power received at long range while experiencing different packet error rates) as compared to previous IEEE 802.11 standards. Additionally, we expose the capabilities of future IEEE 802.11ah in supporting different IoT applications. In addition, we provide a brief overview of the technology contenders that are competing to cover the IoT communications framework. Numerical results are presented showing how the future IEEE 802.11ah specification offers the features required by IoT communications, thus putting forward IEEE 802.11ah as a technology to cater the needs of the Internet of Things paradigm. Finally, we propose an analytical model (named e-model) that provides an evaluation of the RAW onfiguration performance, allowing a fast adaptation of RAW grouping policies, in accordance to varying channel conditions. We base the e-model in known saturation models, which we adapted to include the IEEE 802.11ah’s PHY and MAC layer modifications and to support different bit rate and packet sizes. As a proof of concept, we use the proposed model to compare the performance of different grouping strategies,showing that the e-model is a useful analysis tool in RAW-enabled scenarios. We validate the model with existing IEEE 802.11ah implementation for ns-3.La clave del concepto Internet de las cosas (IoT) es que utiliza un sistema de comunicación inalámbrica, el cual actúa como puente para la entrega de datos y mensajes de control entre las "cosas" conectadas y el Internet. Desde la concepción del IoT, se han desarrollado gran cantidad de aplicaciones y tecnologías prometedoras que cambiarán distintos aspectos de nuestra vida diaria.Sin embargo, las tecnologías de redes computacionales inalámbricas existentes carecen de la capacidad de soportar las características del IoT, como las grandes cantidades de envío y recepción de datos desde múltiples dispositivos distribuidos en un área amplia, donde los dispositivos IoT funcionan con baterías. Para respaldar el paradigma del IoT, IEEE 802.11ah, la cual es una tecnología habilitadora del Internet de las cosas, para el cual la gestión eficiente de miles de dispositivos es una función clave. IEEE 802.11ah es uno de los estándares más prometedores y atractivos, desde su concepción orientada para IoT, su objetivo principal es cerrar la brecha entre las redes móviles tradicionales y la demandada por el IoT. Con este objetivo en mente, IEEE 802.11ah incluye entre sus características especificas el mecanismo de ventana de acceso restringido (RAW, por sus siglas en ingles), el cual define un nuevo período de acceso al canal libre de contención, reduciendo la misma al permitir transmisiones para pequeños grupos de estaciones. Nótese que para obtener una agrupación óptima de estaciones RAW, se requiere una evaluación de las distintas configuraciones posibles. En esta tesis, primero discutimos las principales mejoras de las capas PHY y MAC propuestas para IEEE 802.11ah. Además, investigamos la operatividad de IEEE 802.11ah como enlace de backhaul para conectar dispositivos a distancias largas. También, comparamos el estándar antes mencionado con las notables especificaciones IEEE 802.11 anteriores (es decir, IEEE 802.11n y IEEE 802.11ac), en términos de rendimiento (incluyendo y excluyendo la agregación de tramas de datos) y utilizando los esquemas de modulación más robustos. Los resultados muestran mejores resultados en cuanto al rendimiento de IEEE 802.11ah (en términos de potencia recibida a largo alcance, mientras se experimentan diferentes tasas de error de paquetes de datos) en comparación con los estándares IEEE 802.11 anteriores.Además, exponemos las capacidades de IEEE 802.11ah para admitir diferentes aplicaciones de IoT. A su vez, proporcionamos una descripción general de los competidores tecnológicos, los cuales contienden para cubrir el marco de comunicaciones IoT. También se presentan resultados numéricos que muestran cómo la especificación IEEE 802.11ah ofrece las características requeridas por las comunicaciones IoT, presentando así a IEEE 802.11ah como una tecnología que puede satisfacer las necesidades del paradigma de Internet de las cosas.Finalmente, proponemos un modelo analítico (denominado e-model) que proporciona una evaluación del rendimiento utilizando la característica RAW con múltiples configuraciones, el cual permite una rápida adaptación de las políticas de agrupación RAW, de acuerdo con las diferentes condiciones del canal de comunicación. Basamos el e-model en modelos de saturación conocidos, que adaptamos para incluir las modificaciones de la capa MAC y PHY de IEEE 802.11ah y para poder admitir diferentes velocidades de transmisión de datos y tamaños de paquetes. Como prueba de concepto, utilizamos el modelo propuesto para comparar el desempeño de diferentes estrategias de agrupación, mostrando que el e-model es una herramienta de análisis útil en escenarios habilitados para RAW. Cabe mencionar que también validamos el modelo con la implementación IEEE 802.11ah existente para ns-3

Scalable and rate adaptive wireless multimedia multicast

The methods that are described in this work enable highly efficient audio-visual streaming over wireless digital communication systems to an arbitrary number of receivers. In the focus of this thesis is thus point-to-multipoint transmission at constrained end-to-end delay. A fundamental difference as compared to point-to-point connections between exactly two communicating sending and receiving stations is in conveying information about successful or unsuccessful packet reception at the receiver side. The information to be transmitted is available at the sender, whereas the information about successful reception is only available to the receiver. Therefore, feedback about reception from the receiver to the sender is necessary. This information may be used for simple packet repetition in case of error, or adaptation of the bit rate of transmission to the momentary bit rate capacity of the channel, or both. This work focuses on the single transmission (including retransmissions) of data from one source to multiple destinations at the same time. A comparison with multi-receiver sequentially redundant transmission systems (simulcast MIMO) is made. With respect to feedback, this work considers time division multiple access systems, in which a single channel is used for data transmission and feedback. Therefore, the amount of time that can be spent for transmitting feedback is limited. An increase in time used for feedback transmissions from potentially many receivers results in a decrease in residual time which is usable for data transmission. This has direct impact on data throughput and hence, the quality of service. In the literature, an approach to reduce feedback overhead which is based on simultaneous feedback exists. In the scope of this work, simultaneous feedback implies equal carrier frequency, bandwidth and signal shape, in this case orthogonal frequency-division multiplex signals, during the event of the herein termed feedback aggregation in time. For this scheme, a constant amount of time is spent for feedback, independent of the number of receivers giving feedback about reception. Therefore, also data throughput remains independent of the number of receivers. This property of audio-visual digital transmission is taken for granted for statically configured, single purpose systems, such as terrestrial television. In the scope of this work are, however, multi-user and multi-purpose digital communication networks. Wireless LANs are a well-known example and are covered in detail herein. In suchlike systems, it is of great importance to remain independent of the number of receivers, as otherwise the service of ubiquitous digital connectivity is at the risk of being degraded. In this regard, the thesis at hand elaborates at what bit rates audio-visual transmission to multiple receivers may take place in conjunction with feedback aggregation. It is shown that the scheme achieves a multi-user throughput gain when used in conjunction with adaptivity of the bit rate to the channel. An assumption is the use of an ideal overlay packet erasure correcting code in this case. Furthermore, for delay constrained transmission, such as in so-called live television, throughput bit rates are examined. Applications have to be tolerant to a certain level of residual error in case of delay constrained transmission. Improvement of the rate adaptation algorithm is shown to increase throughput while residual error rates are decreased. Finally, with a consumer hardware prototype for digital live-TV re-distribution in the local wireless network, most of the mechanisms as described herein can be demonstrated.Die in vorliegender Arbeit aufgezeigten Methoden der paketbasierten drahtlosen digitalen Kommunikation ermöglichen es, Fernsehinhalte, aber auch audio-visuelle Datenströme im Allgemeinen, bei hoher Effizienz an beliebig große Gruppen von Empfängern zu verteilen. Im Fokus dieser Arbeit steht damit die Punkt- zu Mehrpunktübertragung bei begrenzter Ende-zu-Ende Verzögerung. Ein grundlegender Unterschied zur Punkt-zu-Punkt Verbindung zwischen genau zwei miteinander kommunizierenden Sender- und Empfängerstationen liegt in der Übermittlung der Information über erfolgreichen oder nicht erfolgreichen Paketempfang auf Seite der Empfänger. Da die zu übertragende Information am Sender vorliegt, die Information über den Erfolg der Übertragung jedoch ausschließlich beim jeweiligen Empfänger, muss eine Erfolgsmeldung auf dem Rückweg von Empfänger zu Sender erfolgen. Diese Information wird dann zum Beispiel zur einfachen Paketwiederholung im nicht erfolgreichen Fall genutzt, oder aber um die Übertragungsrate an die Kapazität des Kanals anzupassen, oder beides. Grundsätzlich beschäftigt sich diese Arbeit mit der einmaligen, gleichzeitigen Übertragung von Information (einschließlich Wiederholungen) an mehrere Empfänger, wobei ein Vergleich zu an mehrere Empfänger sequentiell redundant übertragenden Systemen (Simulcast MIMO) angestellt wird. In dieser Arbeit ist die Betrachtung bezüglich eines Rückkanals auf Zeitduplexsysteme beschränkt. In diesen Systemen wird der Kanal für Hin- und Rückweg zeitlich orthogonalisiert. Damit steht für die Übermittlung der Erfolgsmeldung eine beschränkte Zeitdauer zur Verfügung. Je mehr an Kanalzugriffszeit für die Erfolgsmeldungen der potentiell vielen Empfänger verbraucht wird, desto geringer wird die Restzeit, in der dann entsprechend weniger audio-visuelle Nutzdaten übertragbar sind, was sich direkt auf die Dienstqualität auswirkt. Ein in der Literatur weniger ausführlich betrachteter Ansatz ist die gleichzeitige Übertragung von Rückmeldungen mehrerer Teilnehmer auf gleicher Frequenz und bei identischer Bandbreite, sowie unter Nutzung gleichartiger Signale (hier: orthogonale Frequenzmultiplexsignalformung). Das Schema wird in dieser Arbeit daher als zeitliche Aggregation von Rückmeldungen, engl. feedback aggregation, bezeichnet. Dabei wird, unabhängig von der Anzahl der Empfänger, eine konstante Zeitdauer für Rückmeldungen genutzt, womit auch der Datendurchsatz durch zusätzliche Empfänger nicht notwendigerweise sinkt. Diese Eigenschaft ist aus statisch konfigurierten und für einen einzigen Zweck konzipierten Systemen, wie z. B. der terrestrischen Fernsehübertragung, bekannt. In dieser Arbeit werden im Gegensatz dazu jedoch am Beispiel von WLAN Mehrzweck- und Mehrbenutzersysteme betrachtet. Es handelt sich in derartigen Systemen zur digitalen Datenübertragung dabei um einen entscheidenden Vorteil, unabhängig von der Empfängeranzahl zu bleiben, da es sonst unweigerlich zu Einschränkungen in der Güte der angebotenen Dienstleistung der allgegenwärtigen digitalen Vernetzung kommen muss. Vorliegende Arbeit zeigt in diesem Zusammenhang auf, welche Datenraten unter Benutzung von feedback aggregation in der Verteilung an mehrere Empfänger und in verschiedenen Szenarien zu erreichen sind. Hierbei zeigt sich, dass das Schema im Zusammenspiel mit einer Adaption der Datenrate an den Übertragungskanal inhärent einen Datenratengewinn durch Mehrbenutzerempfang zu erzielen vermag, wenn ein überlagerter idealer Paketauslöschungsschutz-Code angenommen wird. Des weiteren wird bei der Übertragung mit zeitlich begrenzter Ausführungsdauer, z. B. dem sogenannten Live-Fernsehen, aufgezeigt, wie sich die erreichbare Datenrate reduziert und welche Restfehlertoleranz an die Übertragung gestellt werden muss. Hierbei wird ebenso aufgezeigt, wie sich durch Verbesserung der Ratenadaption erstere erhöhen und zweitere verringern lässt. An einem auf handelsüblichen Computer-Systemen realisiertem Prototypen zur Live-Fernsehübertragung können die hierin beschriebenen Mechanismen zu großen Teilen gezeigt werden