SAR interferometry at Venus for topography and change detection

AbstractSince the Magellan radar mapping of Venus in the early 1990’s, techniques of synthetic aperture radar interferometry (InSAR) have become the standard approach to mapping topography and topographic change on Earth. Here we investigate a hypothetical radar mission to Venus that exploits these new methods. We focus on a single spacecraft repeat-pass InSAR mission and investigate the radar and mission parameters that would provide both high spatial resolution topography as well as the ability to detect subtle variations in the surface. Our preferred scenario is a longer-wavelength radar (S or L-band) placed in a near-circular orbit at 600km altitude. Using longer wavelengths minimizes the required radar bandwidth and thus the amount of data that will be transmitted back to earth; it relaxes orbital control and knowledge requirements. During the first mapping cycle a global topography map would be assembled from interferograms taken from adjacent orbits. This approach is viable due to the slow rotation rate of Venus, causing the interferometric baseline between adjacent orbits to vary from only 11km at the equator to zero at the inclination latitude. To overcome baseline decorrelation at lower latitudes, the center frequency of a repeated pass will be adjusted relative to the center frequency of its reference pass. During subsequent mapping cycles, small baseline SAR acquisitions will be used to search for surface decorrelation due to lava flows. While InSAR methods are used routinely on Earth, their application to Venus could be complicated by phase distortions caused by the thick Venus atmosphere

insar decorrelation to assess and prevent volcanic risk

SAR� can� be� invaluable� describing� pre�eruption� surface� deformation� and� improving� the� understanding� of� volcanic� processes.� This� work� studies� correlation� of� pairs� of� SAR� images� focusing� on� the� inༀ䃻uence� of� surface,� climate� conditions� and� acquisition� band.� Chosen� L�band� and� C�band� images� (ENVISAT,� ERS� and� ALOS)� cover� most� of� the� Yellowstone� caldera� (USA)� over� a� span� of� 4� years,� sampling� all� the� seasons.� Interferograms� and� correlation� maps� are� generated� and� studied� in� relation� to� snow� depth� and� temperature.� To� isolate� temporal� decorrelation� pairs� of� images� with� the� shortest� baseline� are� chosen.� Results� show� good� performance� during� winter,� bad� attitude� towards� wet� snow� and� good� coherence� during� summer� with� L�band� performing� better� over� vegetation

Application of Differential and Polarimetric Synthetic Aperture Radar (SAR) Interferometry for Studying Natural Hazards

In the following work, I address the problem of coherence loss in standard Differential Interferometric SAR (DInSAR) processing, which can result in incomplete or poor quality deformation measurements in some areas. I incorporate polarimetric information with DInSAR in a technique called Polarimetric SAR Interferometry (PolInSAR) in order to acquire more accurate and detailed maps of surface deformation. In Chapter 2, I present a standard DInSAR study of the Ahar double earthquakes (Mw=6.4 and 6.2) which occurred in northwest Iran, August 11, 2012. The DInSAR coseismic deformation map was affected by decorrelation noise. Despite this, I employed an advanced inversion technique, in combination with a Coulomb stress analysis, to find the geometry and the slip distribution on the ruptured fault plane. The analysis shows that the two earthquakes most likely occurred on a single fault, not on conjugate fault planes. This further implies that the minor strike-slip faults play more significant role in accommodating convergence stress accumulation in the northwest part of Iran. Chapter 3 presents results from the application of PolInSAR coherence optimization on quad-pol RADARSAT-2 images. The optimized solution results in the identification of a larger number of reliable measurement points, which otherwise are not recognized by the standard DInSAR technique. I further assess the quality of the optimized interferometric phase, which demonstrates an increased phase quality with respect to those phases recovered by applying standard DInSAR alone. Chapter 4 discusses results from the application of PolInSAR coherence optimization from different geometries to the study of creep on the Hayward fault and landslide motions near Berkeley, CA. The results show that the deformation rates resolved by PolInSAR are in agreement with those of standard DInSAR. I also infer that there is potential motion on a secondary fault, northeast and parallel to the Hayward fault, which may be creeping with a lower velocity

Utilization of bistatic TanDEM-X data to derive land cover information

Forests have significance as carbon sink in climate change. Therefore, it is of high importance to track land use changes as well as to estimate the state as carbon sink. This is useful for sustainable forest management, land use planning, carbon modelling, and support to implement international initiatives like REDD+ (Reducing Emissions from Deforestation and Degradation). A combination of field measurements and remote sensing seems most suitable to monitor forests. Radar sensors are considered as high potential due to the weather and daytime independence. TanDEM-X is a interferometric SAR (synthetic aperture radar) mission in space and can be used for land use monitoring as well as estimation of biophysical parameters. TanDEM-X is a X-band system resulting in low penetration depth into the forest canopy. Interferometric information can be useful, whereas the low penetration can be considered as an advantage. The interferometric height is assumable as canopy height, which is correlated with forest biomass. Furthermore, the interferometric coherence is mainly governed by volume decorrelation, whereas temporal decorrelation is minimized. This information can be valuable for quantitative estimations and land use monitoring. The interferometric coherence improved results in comparison to land use classifications without coherence of about 10% (75% vs. 85%). Especially the differentiation between forest classes profited from coherence. The coherence correlated with aboveground biomass in a R² of about 0.5 and resulted in a root mean square error (RSME) of 14%. The interferometric height achieved an even higher correlation with the biomass (R²=0.68) resulting in cross-validated RMSE of 7.5%. These results indicated that TanDEM-X can be considered as valuable and consistent data source for forest monitoring. Especially interferometric information seemed suitable for biomass estimation

Estimation of biophysical parameters in boreal forests from ERS and JERS SAR interferometry

The thesis describes investigations concerning the evaluation of ERS and JERS SAR images and repeat-pass interferometric SAR images for the retrieval of biophysical parameters in boreal forests. The availability of extensive data sets of images over several test sites located in Sweden, Finland and Siberia has allowed analysis of temporal dynamics of ERS and JERS backscatter and coherence, and of ERS interferometric phase. Modelling of backscatter, coherence and InSAR phase has been performed by means of the Water Cloud Model (WCM) and the Interferometric Water Cloud Model (IWCM); sensitivity analysis and implications for the retrieval of forest biophysical parameters have been thoroughly discussed. Model inversion has been carried out for stem volume retrieval using ERS coherence, ERS backscatter and JERS backscatter, whereas for tree height estimation the ERS interferometric phase has been used. Multi-temporal combination of ERS coherence images, and to a lesser extent of JERS backscatter images, can provide stem volume estimates comparable to stand-wise ground-based measurements. Since the information content of the interferometric phase is strongly degraded by phase noise and uncorrected atmospheric artefacts, the retrieved tree height shows large errors

Advanced satellite radar interferometry for small-scale surface deformation detection

Synthetic aperture radar interferometry (InSAR) is a technique that enables generation of Digital Elevation Models (DEMs) and detection of surface motion at the centimetre level using radar signals transmitted from a satellite or an aeroplane. Deformation observations can be performed due to the fact that surface motion, caused by natural and human activities, generates a local phase shift in the resultant interferogram. The magnitude of surface deformation can be estimated directly as a fraction of the wavelength of the transmitted signal. Moreover, differential InSAR (DInSAR) eliminates the phase signal caused by relief to yield a differential interferogram in which the signature of surface deformation can be seen. Although InSAR applications are well established, the improvement of the interferometry technique and the quality of its products is highly desirable to further enhance its capabilities. The application of InSAR encounters problems due to noise in the interferometric phase measurement, caused by a number of decorrelation factors. In addition, the interferogram contains biases owing to satellite orbit errors and atmospheric heterogeneity These factors dramatically reduce the stlectiveness of radar interferometry in many applications, and, in particular, compromise detection and analysis of small-scale spatial deformations. The research presented in this thesis aim to apply radar interferometry processing to detect small-scale surface deformations, improve the quality of the interferometry products, determine the minimum and maximum detectable deformation gradient and enhance the analysis of the interferometric phase image. The quality of DEM and displacement maps can be improved by various methods at different processing levels. One of the methods is filtering of the interferometric phase.However, while filtering reduces noise in the interferogram, it does not necessarily enhance or recover the signal. Furthermore, the impact of the filter can significantly change the structure of the interferogram. A new adaptive radar interferogram filter has been developed and is presented herein. The filter is based on a modification to the Goldstein radar interferogram filter making the filter parameter dependent on coherence so that incoherent areas are filtered more than coherent areas. This modification minimises the loss of signal while still reducing the level of noise. A methodology leading to the creation of a functional model for determining minimum and maximum detectable deformation gradient, in terms of the coherence value, has been developed. The sets of representative deformation models have been simulated and the associated phase from these models has been introduced to real SAR data acquired by ERS-1/2 satellites. A number of cases of surface motion with varying magnitudes and spatial extent have been simulated. In each case, the resultant surface deformation has been compared with the 'true' surface deformation as defined by the deformation model. Based on those observations, the functional model has been developed. Finally, the extended analysis of the interferometric phase image using a wavelet approach is presented. The ability of a continuous wavelet transform to reveal the content of the wrapped phase interferogram, such as (i) discontinuities, (ii) extent of the deformation signal, and (iii) the magnitude of the deformation signal is examined. The results presented represent a preliminary study revealing the wavelet method as a promising technique for interferometric phase image analysis

Ground-based synthetic aperture radar (GBSAR) interferometry for deformation monitoring

Ph. D ThesisGround-based synthetic aperture radar (GBSAR), together with interferometry, represents a powerful tool for deformation monitoring. GBSAR has inherent flexibility, allowing data to be collected with adjustable temporal resolutions through either continuous or discontinuous mode. The goal of this research is to develop a framework to effectively utilise GBSAR for deformation monitoring in both modes, with the emphasis on accuracy, robustness, and real-time capability. To achieve this goal, advanced Interferometric SAR (InSAR) processing algorithms have been proposed to address existing issues in conventional interferometry for GBSAR deformation monitoring. The proposed interferometric algorithms include a new non-local method for the accurate estimation of coherence and interferometric phase, a new approach to selecting coherent pixels with the aim of maximising the density of selected pixels and optimizing the reliability of time series analysis, and a rigorous model for the correction of atmospheric and repositioning errors. On the basis of these algorithms, two complete interferometric processing chains have been developed: one for continuous and the other for discontinuous GBSAR deformation monitoring. The continuous chain is able to process infinite incoming images in real time and extract the evolution of surface movements through temporally coherent pixels. The discontinuous chain integrates additional automatic coregistration of images and correction of repositioning errors between different campaigns. Successful deformation monitoring applications have been completed, including three continuous (a dune, a bridge, and a coastal cliff) and one discontinuous (a hillside), which have demonstrated the feasibility and effectiveness of the presented algorithms and chains for high-accuracy GBSAR interferometric measurement. Significant deformation signals were detected from the three continuous applications and no deformation from the discontinuous. The achieved results are justified quantitatively via a defined precision indicator for the time series estimation and validated qualitatively via a priori knowledge of these observing sites.China Scholarship Council (CSC), Newcastle Universit