57 research outputs found

    Time diversity solutions to cope with lost packets

    Get PDF
    A dissertation submitted to Departamento de Engenharia ElectrotĂ©cnica of Faculdade de CiĂȘncias e Tecnologia of Universidade Nova de Lisboa in partial fulfilment of the requirements for the degree of Doctor of Philosophy in Engenharia ElectrotĂ©cnica e de ComputadoresModern broadband wireless systems require high throughputs and can also have very high Quality-of-Service (QoS) requirements, namely small error rates and short delays. A high spectral efficiency is needed to meet these requirements. Lost packets, either due to errors or collisions, are usually discarded and need to be retransmitted, leading to performance degradation. An alternative to simple retransmission that can improve both power and spectral efficiency is to combine the signals associated to different transmission attempts. This thesis analyses two time diversity approaches to cope with lost packets that are relatively similar at physical layer but handle different packet loss causes. The first is a lowcomplexity Diversity-Combining (DC) Automatic Repeat reQuest (ARQ) scheme employed in a Time Division Multiple Access (TDMA) architecture, adapted for channels dedicated to a single user. The second is a Network-assisted Diversity Multiple Access (NDMA) scheme, which is a multi-packet detection approach able to separate multiple mobile terminals transmitting simultaneously in one slot using temporal diversity. This thesis combines these techniques with Single Carrier with Frequency Division Equalizer (SC-FDE) systems, which are widely recognized as the best candidates for the uplink of future broadband wireless systems. It proposes a new NDMA scheme capable of handling more Mobile Terminals (MTs) than the user separation capacity of the receiver. This thesis also proposes a set of analytical tools that can be used to analyse and optimize the use of these two systems. These tools are then employed to compare both approaches in terms of error rate, throughput and delay performances, and taking the implementation complexity into consideration. Finally, it is shown that both approaches represent viable solutions for future broadband wireless communications complementing each other.Fundação para a CiĂȘncia e Tecnologia - PhD grant(SFRH/BD/41515/2007); CTS multi-annual funding project PEst-OE/EEI/UI0066/2011, IT pluri-annual funding project PEst-OE/EEI/LA0008/2011, U-BOAT project PTDC/EEATEL/ 67066/2006, MPSat project PTDC/EEA-TEL/099074/2008 and OPPORTUNISTICCR project PTDC/EEA-TEL/115981/200

    MAC Protocols for Wireless Mesh Networks with Multi-beam Antennas: A Survey

    Full text link
    Multi-beam antenna technologies have provided lots of promising solutions to many current challenges faced in wireless mesh networks. The antenna can establish several beamformings simultaneously and initiate concurrent transmissions or receptions using multiple beams, thereby increasing the overall throughput of the network transmission. Multi-beam antenna has the ability to increase the spatial reuse, extend the transmission range, improve the transmission reliability, as well as save the power consumption. Traditional Medium Access Control (MAC) protocols for wireless network largely relied on the IEEE 802.11 Distributed Coordination Function(DCF) mechanism, however, IEEE 802.11 DCF cannot take the advantages of these unique capabilities provided by multi-beam antennas. This paper surveys the MAC protocols for wireless mesh networks with multi-beam antennas. The paper first discusses some basic information in designing multi-beam antenna system and MAC protocols, and then presents the main challenges for the MAC protocols in wireless mesh networks compared with the traditional MAC protocols. A qualitative comparison of the existing MAC protocols is provided to highlight their novel features, which provides a reference for designing the new MAC protocols. To provide some insights on future research, several open issues of MAC protocols are discussed for wireless mesh networks using multi-beam antennas.Comment: 22 pages, 6 figures, Future of Information and Communication Conference (FICC) 2019, https://doi.org/10.1007/978-3-030-12388-8_

    Energy-efficient diversity combining for different access schemes in a multi-path dispersive channel

    Get PDF
    Dissertação para obtenção do Grau de Doutor em Engenharia Electrotécnica e ComputadoresThe forthcoming generation of mobile communications, 5G, will settle a new standard for a larger bandwidth and better Quality of Service (QoS). With the exploding growth rate of user generated data, wireless standards must cope with this growth and at the same time be energy efficient to avoid depleting the batteries of wireless devices. Besides these issues, in a broadband wireless setting QoS can be severely affected from a multipath dispersive channel and therefore be energy demanding. Cross-layered architectures are a good choice to enhance the overall performance of a wireless system. Examples of cross-layered Physical (PHY) - Medium Access Control (MAC) architectures are type-II Diversity Combining (DC) Hybrid-ARQ (H-ARQ) and Multi-user Detection (MUD) schemes. Cross-layered type-II DC H-ARQ schemes reuse failed packet transmissions to enhance data reception on posterior retransmissions; MUD schemes reuse data information from previously collided packets on posterior retransmissions to enhance data reception. For a multipath dispersive channel, a PHY layer analytical model is proposed for Single-Carrier with Frequency Domain Equalization (SC-FDE) that supports DC H-ARQ and MUD. Based on this analytical model, three PHY-MAC protocols are proposed. A crosslayered Time Division Multiple Access (TDMA) scheme that uses DC H-ARQ is modeled and its performance is studied in this document; the performance analysis shows that the scheme performs better with DC and achieves a better energy efficiency at the cost of a higher delay. A novel cross-layered prefix-assisted Direct-Sequence Code Division Multiple Access (DS-CDMA) scheme is proposed and modeled in this document, it uses principles of DC and MUD. This protocol performs better by means of additional retransmissions, achieving better energy efficiency, at the cost of higher redundancy from a code spreading gain. Finally, a novel cross-layered protocol H-ARQ Network Division Multiple Access (H-NDMA) is proposed and modeled, where the combination of DC H-ARQ and MUD is used with the intent of maximizing the system capacity with a lower delay; system results show that the proposed scheme achieves better energy efficiency and a better performance at the cost of a higher number of retransmissions. A comparison of the three cross-layered protocols is made, using the PHY analytical model, under normalized conditions using the same amount of maximum redundancy. Results show that the H-NDMA protocol, in general, obtains the best results, achieving a good performance and a good energy efficiency for a high channel load and low Signal-to-Noise Ratio (SNR). TDMA with DC H-ARQ achieves the best energy efficiency, although presenting the worst delay. Prefix-assisted DS-CDMA in the other hand shows good delay results but presents the worst throughput and energy efficiency

    A random access MAC protocol for MPR satellite networks

    Get PDF
    Dissertação apresentada para obtenção do Grau de Mestre em Engenharia ElectrotĂ©cnica e de Computadores, pela Universidade Nova de Lisboa, Faculdade de CiĂȘncias e TecnologiaRandom access approaches for Low Earth Orbit (LEO) satellite networks are usually incompatible with the Quality of Service (QoS) requirements of multimedia tra c, especially when hand-held devices must operate with very low power. Cross-Layered optimization architectures, combined with Multipacket Reception (MPR)schemes are a good choice to enhance the overall performance of a wireless system. Hybrid Network-assisted Diversity Multiple Access (H-NDMA) protocol, exhibits high energy e ciency, with MPR capability, but its use with satellites is limited by the high round trip time. This protocol was adapted to satellites, in Satellite-NDMA, but it required a pre-reservation mechanism that introduces a signi cant delay. This dissertation proposes a random access protocol that uses H-NDMA, for Low Earth Orbit (LEO) satellite networks, named Satellite Random-NDMA (SR-NDMA). The protocol addresses the problem inherent to satellite networks (large round trip time and signi cant energy consumption) de ning a hybrid approach with an initial random access plus possible additional scheduled retransmissions. An MPR receiver combines the multiple copies received, gradually reducing the error rate. Analytical performance models are proposed for the throughput, delay, jitter and energy e ciency considering nite queues at the terminals. It is also addressed the energy e ciency optimization, where the system parameters are calculated to guarantee the QoS requirements. The proposed system's performance is evaluated for a Single-Carrier with Frequency Domain Equalization (SC-FDE) receiver. Results show that the proposed system is energy e cient and can provide enough QoS to support services such as video telephony

    Modern Random Access for Satellite Communications

    Full text link
    The present PhD dissertation focuses on modern random access (RA) techniques. In the first part an slot- and frame-asynchronous RA scheme adopting replicas, successive interference cancellation and combining techniques is presented and its performance analysed. The comparison of both slot-synchronous and asynchronous RA at higher layer, follows. Next, the optimization procedure, for slot-synchronous RA with irregular repetitions, is extended to the Rayleigh block fading channel. Finally, random access with multiple receivers is considered.Comment: PhD Thesis, 196 page

    Position-based routing and MAC protocols for wireless ad-hoc networks

    Get PDF
    This thesis presents the Forecasting Routing Technique (FORTEL), a routing protocol for Mobile Ad-Hoc Networks (MANETs) based on the nodes' Location Information. FORTEL stores the nodes' location information in the Location Table (LT) in order to construct routes between the source and the destination nodes. FORTEL follows the source routing strategy, which has rarely been applied in position-based routing. According to the source routing strategy, the end-to-end route is attached to the packet, therefore, the processing cost, in regards to the intermediate nodes that simply relay the packet according to route, is minimized. FORTEL's key mechanisms include: first, the location update scheme, employed to keep the LT entries up-to-date with the network topology. Besides the mobility variation and the constant rate location update schemes applied, a window location update scheme is presented to increase the LT's information accuracy. Second, the switching mechanism, between "Hello" message and location update employed, to reduce the protocol's routing overhead. Third and most important is the route computation mechanism, which is integrated with a topology forecasting technique to construct up-to-date routes between the communication peers, aiming to achieve high delivery rate and increase the protocol robustness against the nodes' movement. FORTEL demonstrates higher performance as compared to other MANET's routing protocols, and it delivers up to 20% more packets than AODV and up to 60 % more than DSR and OLSR, while maintaining low levels of routing overhead and network delay at the same time. The effectiveness of the window update scheme is also discussed, and it proves to increase FORTEL's delivery rate by up to 30% as compared to the other update schemes. A common and frequently occurring phenomenon, in wireless networks, is the Hidden Terminal problem that significantly impacts the communication performance and the efficiency of the routing and MAC protocols. Beaconless routing approach in MANETs, which delivers data packets without prior knowledge of any sort `of information, suffers from packet duplication caused by the hidden nodes during the contention process. Moreover, the throughput of the IEEE MAC protocol decreases dramatically when the hidden terminal problem occurs. RTS/CTS mechanism fails to eliminate the problem and can further degrade the network's performance by introducing additional overhead. To tackle these challenges, this thesis presents two techniques, the Sender Suppression Algorithm and the Location-Aided MAC, where both rely on the nodes' position to eliminate packet duplication in the beaconless routing and improve the performance of the 802.11 MAC respectively. Both schemes are based on the concept of grouping the nodes into zones and assign different time delay to each one. According to the Sender Suppression Algorithm, the sender's forwarding area is divided into three zones, therefore, the local timer, set to define the time that the receiver has to wait before responding to the sender's transmission, is added to the assigned zone delay. Following the first response, the sender interferes and suppresses the receivers with active timer of. On the other hand, the Location-Aided MAC, essentially a hybrid MAC, combines the concepts of time division and carrier sensing. The radio range of the wireless receiver is partitioned into four zones with different zone delays assigned to each zone. Channel access within the zone is purely controlled by CSMA/CA protocol, while it is time-based amongst zones. The effectiveness of the proposed techniques is demonstrated through simulation tests. Location-Aided MAC considerably improves the network's throughput compared to CSMA/CA and RTS/CTS. However, remarkable results come when the proposed technique and the RTS/CTS are combined, which achieves up to 20% more throughput as compared to the standalone RTS/CTS. Finally, the thesis presents a novel link lifetime estimation method for greedy forwarding to compute the link duration between two nodes. Based on a newly introduced Stability-Aware Greedy (SAG) scheme, the proposed method incorporates the destination node in the computation process and thus has a significant advantage over the conventional method, which only considers the information of the nodes composing the link.EThOS - Electronic Theses Online ServiceGBUnited Kingdo

    Position-based routing and MAC protocols for wireless ad-hoc networks

    Get PDF
    This thesis presents the Forecasting Routing Technique (FORTEL), a routing protocol for Mobile Ad-Hoc Networks (MANETs) based on the nodes' Location Information. FORTEL stores the nodes' location information in the Location Table (LT) in order to construct routes between the source and the destination nodes. FORTEL follows the source routing strategy, which has rarely been applied in position-based routing. According to the source routing strategy, the end-to-end route is attached to the packet, therefore, the processing cost, in regards to the intermediate nodes that simply relay the packet according to route, is minimized. FORTEL's key mechanisms include: first, the location update scheme, employed to keep the LT entries up-to-date with the network topology. Besides the mobility variation and the constant rate location update schemes applied, a window location update scheme is presented to increase the LT's information accuracy. Second, the switching mechanism, between "Hello" message and location update employed, to reduce the protocol's routing overhead. Third and most important is the route computation mechanism, which is integrated with a topology forecasting technique to construct up-to-date routes between the communication peers, aiming to achieve high delivery rate and increase the protocol robustness against the nodes' movement. FORTEL demonstrates higher performance as compared to other MANET's routing protocols, and it delivers up to 20% more packets than AODV and up to 60 % more than DSR and OLSR, while maintaining low levels of routing overhead and network delay at the same time. The effectiveness of the window update scheme is also discussed, and it proves to increase FORTEL's delivery rate by up to 30% as compared to the other update schemes. A common and frequently occurring phenomenon, in wireless networks, is the Hidden Terminal problem that significantly impacts the communication performance and the efficiency of the routing and MAC protocols. Beaconless routing approach in MANETs, which delivers data packets without prior knowledge of any sort `of information, suffers from packet duplication caused by the hidden nodes during the contention process. Moreover, the throughput of the IEEE MAC protocol decreases dramatically when the hidden terminal problem occurs. RTS/CTS mechanism fails to eliminate the problem and can further degrade the network's performance by introducing additional overhead. To tackle these challenges, this thesis presents two techniques, the Sender Suppression Algorithm and the Location-Aided MAC, where both rely on the nodes' position to eliminate packet duplication in the beaconless routing and improve the performance of the 802.11 MAC respectively. Both schemes are based on the concept of grouping the nodes into zones and assign different time delay to each one. According to the Sender Suppression Algorithm, the sender's forwarding area is divided into three zones, therefore, the local timer, set to define the time that the receiver has to wait before responding to the sender's transmission, is added to the assigned zone delay. Following the first response, the sender interferes and suppresses the receivers with active timer of. On the other hand, the Location-Aided MAC, essentially a hybrid MAC, combines the concepts of time division and carrier sensing. The radio range of the wireless receiver is partitioned into four zones with different zone delays assigned to each zone. Channel access within the zone is purely controlled by CSMA/CA protocol, while it is time-based amongst zones. The effectiveness of the proposed techniques is demonstrated through simulation tests. Location-Aided MAC considerably improves the network's throughput compared to CSMA/CA and RTS/CTS. However, remarkable results come when the proposed technique and the RTS/CTS are combined, which achieves up to 20% more throughput as compared to the standalone RTS/CTS. Finally, the thesis presents a novel link lifetime estimation method for greedy forwarding to compute the link duration between two nodes. Based on a newly introduced Stability-Aware Greedy (SAG) scheme, the proposed method incorporates the destination node in the computation process and thus has a significant advantage over the conventional method, which only considers the information of the nodes composing the link.EThOS - Electronic Theses Online ServiceGBUnited Kingdo

    Incidences of the improvement of the interactions between MAC and routing protocols on MANET performance

    Full text link

    Improving the Performance of Wireless LANs

    Get PDF
    This book quantifies the key factors of WLAN performance and describes methods for improvement. It provides theoretical background and empirical results for the optimum planning and deployment of indoor WLAN systems, explaining the fundamentals while supplying guidelines for design, modeling, and performance evaluation. It discusses environmental effects on WLAN systems, protocol redesign for routing and MAC, and traffic distribution; examines emerging and future network technologies; and includes radio propagation and site measurements, simulations for various network design scenarios, numerous illustrations, practical examples, and learning aids
    • 

    corecore