2,444 research outputs found

    High performance RF and baseband building blocks for wireless receivers

    Get PDF
    Because of the unique architecture of wireless receivers, a designer must understand both the high frequency aspects as well as the low-frequency analog considerations for different building blocks of the receiver. The primary goal of this research work is to explore techniques for implementing high performance RF and baseband building blocks for wireless applications. Several novel techniques to improve the performance of analog building blocks are presented. An enhanced technique to couple two LC resonators is presented which does not degrade the loaded quality factor of the resonators which results in an increased dynamic range. A novel technique to automatically tune the quality factor of LC resonators is presented. The proposed scheme is stable and fast and allows programming both the quality factor and amplitude response of the LC filter. To keep the oscillation amplitude of LC VCOs constant and thus achieving a minimum phase noise and a reliable startup, a stable amplitude control loop is presented. The proposed scheme has been also used in a master-slave quality factor tuning of LC filters. An efficient and low-cost architecture for a 3.1GHz-10.6GHz ultra-wide band frequency synthesizer is presented. The proposed scheme is capable of generating 14A novel pseudo-differential transconductance amplifier is presented. The proposed scheme takes advantage of the second-order harmonic available at the output current of pseudo-differential structure to cancel the third-order harmonic distortion. A novel nonlinear function is proposed which inherently removes the third and the fifth order harmonics at its output signal. The proposed nonlinear block is used in a bandpass-based oscillator to generate a highly linear sinusoidal output. Finally, a linearized BiCMOS transconductance amplifier is presented. This transconductance is used to build a third-order linear phase low pass filter with a cut-off frequency of 264MHz for an ultra-wide band receiver. carrier frequencies

    High-frequency oscillator design for integrated transceivers

    Get PDF

    Wake-up receiver based ultra-low-power WBAN

    Get PDF

    Theory of phaselock techniques as applied to aerospace transponders

    Get PDF
    Phaselock techniques as applied to aerospace transponder

    Design of high frequency transconductor ladder filters

    Get PDF

    High performance continuous-time filters for information transfer systems

    Get PDF
    Vast attention has been paid to active continuous-time filters over the years. Thus as the cheap, readily available integrated circuit OpAmps replaced their discrete circuit versions, it became feasible to consider active-RC filter circuits using large numbers of OpAmps. Similarly the development of integrated operational transconductance amplifier (OTA) led to new filter configurations. This gave rise to OTA-C filters, using only active devices and capacitors, making it more suitable for integration. The demands on filter circuits have become ever more stringent as the world of electronics and communications has advanced. In addition, the continuing increase in the operating frequencies of modern circuits and systems increases the need for active filters that can perform at these higher frequencies; an area where the LC active filter emerges. What mainly limits the performance of an analog circuit are the non-idealities of the used building blocks and the circuit architecture. This research concentrates on the design issues of high frequency continuous-time integrated filters. Several novel circuit building blocks are introduced. A novel pseudo-differential fully balanced fully symmetric CMOS OTA architecture with inherent common-mode detection is proposed. Through judicious arrangement, the common-mode feedback circuit can be economically implemented. On the level of system architectures, a novel filter low-voltage 4th order RF bandpass filter structure based on emulation of two magnetically coupled resonators is presented. A unique feature of the proposed architecture is using electric coupling to emulate the effect of the coupled-inductors, thus providing bandwidth tuning with small passband ripple. As part of a direct conversion dual-mode 802.11b/Bluetooth receiver, a BiCMOS 5th order low-pass channel selection filter is designed. The filter operated from a single 2.5V supply and achieves a 76dB of out-of-band SFDR. A digital automatic tuning system is also implemented to account for process and temperature variations. As part of a Bluetooth transmitter, a low-power quadrature direct digital frequency synthesizer (DDFS) is presented. Piecewise linear approximation is used to avoid using a ROM look-up table to store the sine values in a conventional DDFS. Significant saving in power consumption, due to the elimination of the ROM, renders the design more suitable for portable wireless communication applications

    Ultra-Low Power Wake Up Receiver For Medical Implant Communications Service Transceiver

    Get PDF
    This thesis explores the specific requirements and challenges for the design of a dedicated wake-up receiver for medical implant communication services equipped with a novel “uncertain-IF†architecture combined with a high – Q filtering MEMS resonator and a free running CMOS ring oscillator as the RF LO. The receiver prototype, implements an IBM 0.18μm mixed-signal 7ML RF CMOS technology and achieves a sensitivity of -62 dBm at 404MHz while consuming \u3c100 μW from a 1 V supply

    A wide dynamic range high-q high-frequency bandpass filter with an automatic quality factor tuning scheme

    Get PDF
    An 80 MHz bandpass filter with a tunable quality factor of 16∼44 using an improved transconductor circuit is presented. A noise optimized biquad structure for high-Q, high- frequency bandpass filter is proposed. The quality factor of the filter is tuned using a new quality factor locked loop algorithm. It was shown that a second-order quality factor locked loop is necessary and sufficient to tune the quality factor of a bandpass filter with zero steady state error. The accuracy, mismatch, and sensitivty analysis of the new tuning scheme was performed and analyzed. Based on the proposed noise optimized filter structure and new quality factor tuning scheme, a biquad filter was designed and fabricated in 0.25 μm BiCMOS process. The measured results show that the biquad filter achieves a SNR of 45 dB at IMD of 40 dB. The P-1dB compression point and IIP3 of the filter are -10 dBm and -2.68 dBm, respectively. The proposed biquad filter and quality factor tuning scheme consumes 58mW and 13 mW of power at 3.3 V supply.Ph.D.Committee Chair: Allen Phillip; Committee Member: Hasler Paul; Committee Member: Keezer David; Committee Member: Kenny James; Committee Member: Pan Ronghu

    Circuits and Systems for On-Chip RF Chemical Sensors and RF FDD Duplexers

    Get PDF
    Integrating RF bio-chemical sensors and RF duplexers helps to reduce cost and area in the current applications. Furthermore, new applications can exist based on the large scale integration of these crucial blocks. This dissertation addresses the integration of RF bio-chemical sensors and RF duplexers by proposing these initiatives. A low power integrated LC-oscillator-based broadband dielectric spectroscopy (BDS) system is presented. The real relative permittivity ε’r is measured as a shift in the oscillator frequency using an on-chip frequency-to-digital converter (FDC). The imaginary relative permittivity ε”r increases the losses of the oscillator tank which mandates a higher dc biasing current to preserve the same oscillation amplitude. An amplitude-locked loop (ALL) is used to fix the amplitude and linearize the relation between the oscillator bias current and ε”r. The proposed BDS system employs a sensing oscillator and a reference oscillator where correlated double sampling (CDS) is used to mitigate the impact of flicker noise, temperature variations and frequency drifts. A prototype is implemented in 0.18 µm CMOS process with total chip area of 6.24 mm^2 to operate in 1-6 GHz range using three dual bands LC oscillators. The achieved standard deviation in the air is 2.1 ppm for frequency reading and 110 ppm for current reading. A tunable integrated electrical balanced duplexer (EBD) is presented as a compact alternative to multiple bulky SAW and BAW duplexers in 3G/4G cellular transceivers. A balancing network creates a replica of the transmitter signal for cancellation at the input of a single-ended low noise amplifier (LNA) to isolate the receive path from the transmitter. The proposed passive EBD is based on a cross-connected transformer topology without the need of any extra balun at the antenna side. The duplexer achieves around 50 dB TX-RX isolation within 1.6-2.2 GHz range up to 22 dBm. The cascaded noise figure of the duplexer and LNA is 6.5 dB, and TX insertion loss (TXIL) of the duplexer is about 3.2 dB. The duplexer and LNA are implemented in 0.18 µm CMOS process and occupy an active area of 0.35 mm^2

    Receiver Front-Ends in CMOS with Ultra-Low Power Consumption

    Get PDF
    Historically, research on radio communication has focused on improving range and data rate. In the last decade, however, there has been an increasing demand for low power and low cost radios that can provide connectivity with small devices around us. They should be able to offer basic connectivity with a power consumption low enough to function extended periods of time on a single battery charge, or even energy scavenged from the surroundings. This work is focused on the design of ultra-low power receiver front-ends intended for a receiver operating in the 2.4GHz ISM band, having an active power consumption of 1mW and chip area of 1mm². Low power consumption and small size make it hard to achieve good sensitivity and tolerance to interference. This thesis starts with an introduction to the overall receiver specifications, low power radio and radio standards, front-end and LO generation architectures and building blocks, followed by the four included papers. Paper I demonstrates an inductorless front-end operating at 915MHz, including a frequency divider for quadrature LO generation. An LO generator operating at 2.4GHz is shown in Paper II, enabling a front-end operating above 2GHz. Papers III and IV contain circuits with combined front-end and LO generator operating at or above the full 2.45GHz target frequency. They use VCO and frequency divider topologies that offer efficient operation and low quadrature error. An efficient passive-mixer design with improved suppression of interference, enables an LNA-less design in Paper IV capable of operating without a SAW-filter
    corecore