A Low Noise Sub-Sampling PLL in Which Divider Noise Is Eliminated and PD-CP Noise Is not multiplied by N^2

This paper presents a 2.2-GHz low jitter sub-sampling based PLL. It uses a phase-detector/charge-pump (PD/CP)that sub-samples the VCO output with the reference clock. In contrast to what happens in a classical PLL, the PD/CP noise is not multiplied by N2 in this sub-sampling PLL, resulting in a low noise contribution from the PD/CP. Moreover, no frequency divider is needed in the locked state and hence divider noise and power can be eliminated. An added frequency locked loop guarantees correct frequency locking without degenerating jitter performance when in lock. The PLL is implemented in a standard 0.18- m CMOS process. It consumes 4.2 mA from a 1.8 V supply and occupies an active area of 0.4 X 0.45 m

Hardware simulation of KU-band spacecraft receiver and bit synchronizer, phase 2, volume 1

The acquisition behavior of the PN subsystem of an automatically acquiring spacecraft receiver was studied. A symbol synchronizer subsystem was constructed and integrated into the composite simulation of the receiver. The overall performance of the receiver when subjected to anomalies such as signal fades was evaluated. Potential problems associated with PN/carrier sweep interactions were investigated

Analysis and equalization of data-dependent jitter

Data-dependent jitter limits the bit-error rate (BER) performance of broadband communication systems and aggravates synchronization in phase- and delay-locked loops used for data recovery. A method for calculating the data-dependent jitter in broadband systems from the pulse response is discussed. The impact of jitter on conventional clock and data recovery circuits is studied in the time and frequency domain. The deterministic nature of data-dependent jitter suggests equalization techniques suitable for high-speed circuits. Two equalizer circuit implementations are presented. The first is a SiGe clock and data recovery circuit modified to incorporate a deterministic jitter equalizer. This circuit demonstrates the reduction of jitter in the recovered clock. The second circuit is a MOS implementation of a jitter equalizer with independent control of the rising and falling edge timing. This equalizer demonstrates improvement of the timing margins that achieve 10/sup -12/ BER from 30 to 52 ps at 10 Gb/s

Solar Power Satellite antenna phase control system hardware simulation, phase 4. Volume 2: Analytical simulation of SPS system performance

The pilot signal parameter optimization and power transponder analyses are presented. The SPS antenna phase control system is modeled and the hardware simulation study described. Ionospheric and system phase error effects and the effects of high power amplifier phase and amplitude jitters are considered. Parameter optimization of the spread spectrum receiver, consisting of the carrier tracking loop and the code tracking loop, is described

Dependence of VCO jitter on coupled noise

In mixed signal systems, the Phase Locked Loop (PLL) forms an integral part of the clock distribution scheme. The PLL is used to generate a local clock frequency, which is much higher than the external clock. The performance of a PLL is greatly influenced by the Voltage Controlled Oscillator (VCO). Any nonlinearity introduced by the VCO affects the synchronization between operation of on-chip circuitry and the external components. The jitter or phase noise of a VCO is the most important non-ideality. Phase noise or jitter becomes critical as system frequency increases. The source of timing error maybe due to various noise sources, with power supply noise and that due to substrate coupling being the major contributors. The thesis presented here deals with the effect of these two noise sources on the time period of the VCO. The peak cycle jitter and cycle-to- cycle jitter due to noise is estimated by developing a relation between the noise source and the deviation in the output voltage in terms of the circuit parameters. First crossing theory approximation has been used to convert the voltage error to timing error. The theory has been extended to analyze the timing error when the two noise sources are present together. Good agreement has been shown between the theoretical prediction and the simulated result. The analysis can be extended to any number of stages for any operating frequency as will be demonstrated in the subsequent chapters

High-speed communication circuits: voltage control oscillators and VCO-derived filters

Voltage Controlled Oscillators (VCO) and filters are the two main topics of focus in this dissertation.;A temperature and process compensated VCO, which is designed to operate at 2 GHz, and whose frequency variation due to incoming data is limited to 1% of its center frequency was presented. The test results show that, without process changes present, the frequency variation due to a temperature change over 0°C to 100°C is around 1.1% of its center frequency. This is a reduction of a factor of 10 when compared to the temperature variation of a conventional VCO.;A new method of designing continuous-time monolithic filters derived from well-known voltage controlled oscillators (VCOs) was introduced. These VCO-derived filters are capable of operating at very high frequencies in standard CMOS processes. Prototype low-pass and band-pass filters designed in a TSMC 0.25 mum process are discussed. Simulation results for the low-pass filter designed for a cutoff frequency of 4.3 GHz show a THD of -40 dB for a 200 mV peak-peak sinusoidal input. The band-pass filter has a resonant frequency programmable from 2.3 GHz to 3.1 GHz, a programmable Q from 3 to 85, and mid-band THD of -40 dB for an 80 mV peak-peak sinusoidal input signal.;A third contribution in this dissertation was the design of a new current mirror with accurate mirror gain for low beta bipolar transistors. High mirror gain accuracy is achieved by using a split-collector transistor to compensate for base currents of the source-coupled

One way Doppler extractor. Volume 1: Vernier technique

A feasibility analysis, trade-offs, and implementation for a One Way Doppler Extraction system are discussed. A Doppler error analysis shows that quantization error is a primary source of Doppler measurement error. Several competing extraction techniques are compared and a Vernier technique is developed which obtains high Doppler resolution with low speed logic. Parameter trade-offs and sensitivities for the Vernier technique are analyzed, leading to a hardware design configuration. A detailed design, operation, and performance evaluation of the resulting breadboard model is presented which verifies the theoretical performance predictions. Performance tests have verified that the breadboard is capable of extracting Doppler, on an S-band signal, to an accuracy of less than 0.02 Hertz for a one second averaging period. This corresponds to a range rate error of no more than 3 millimeters per second

Integrated Circuit Design for Hybrid Optoelectronic Interconnects

This dissertation focuses on high-speed circuit design for the integration of hybrid optoelectronic interconnects. It bridges the gap between electronic circuit design and optical device design by seamlessly incorporating the compact Verilog-A model for optical components into the SPICE-like simulation environment, such as the Cadence design tool. Optical components fabricated in the IME 130nm SOI CMOS process are characterized. Corresponding compact Verilog-A models for Mach-Zehnder modulator (MZM) device are developed. With this approach, electro-optical co-design and hybrid simulation are made possible. The developed optical models are used for analyzing the system-level specifications of an MZM based optoelectronic transceiver link. Link power budgets for NRZ, PAM-4 and PAM-8 signaling modulations are simulated at system-level. The optimal transmitter extinction ratio (ER) is derived based on the required receiver\u27s minimum optical modulation amplitude (OMA). A limiting receiver is fabricated in the IBM 130 nm CMOS process. By side- by-side wire-bonding to a commercial high-speed InGaAs/InP PIN photodiode, we demonstrate that the hybrid optoelectronic limiting receiver can achieve the bit error rate (BER) of 10-12 with a -6.7 dBm sensitivity at 4 Gb/s. A full-rate, 4-channel 29-1 length parallel PRBS is fabricated in the IBM 130 nm SiGe BiCMOS process. Together with a 10 GHz phase locked loop (PLL) designed from system architecture to transistor level design, the PRBS is demonstrated operating at more than 10 Gb/s. Lessons learned from high-speed PCB design, dealing with signal integrity issue regarding to the PCB transmission line are summarized

A Highly Digital VCO-Based ADC With Lookup-Table-Based Background Calibration

CMOS technology scaling has enabled dramatic improvement for digital circuits both in terms of speed and power efficiency. However, most traditional analog-to-digital converter (ADC) architectures are challenged by ever-decreasing supply voltage. The improvement in time resolution enabled by increased digital speeds drives design towards time-domain architectures such as voltage-controlled-oscillator (VCO) based ADCs. The main challenge in VCO-based ADC design is mitigating the nonlinearity of VCO Voltage-to-frequency (V-to-f) characteristics. Achieving signal-to-noise ratio (SNR) performance better than 40dB requires some form of calibration, which can be realized by analog or digital techniques, or some combination. This dissertation proposes a highly digital, reconfigurable VCO-based ADC with lookup-table (LUT) based background calibration based on split ADC architecture. Each of the two split channels, ADC A and B , contains two VCOs in a differential configuration. This helps alleviate even-order distortions as well as increase the dynamic range. A digital controller on chip can reconfigure the ADCs\u27 sampling rates and resolutions to adapt to various application scenarios. Different types of input signals can be used to train the ADC’s LUT parameters through the simple, anti-aliasing continuous-time input to achieve target resolution. The chip is fabricated in a 180 nm CMOS process, and the active area of analog and digital circuits is 0.09 and 0.16mm^2, respectively. Power consumption of the core ADC function is 25 mW. Measured results for this prototype design with 12-b resolution show ENOB improves from uncorrected 5-b to 11.5-b with calibration time within 200 ms (780K conversions at 5 MSps sample rate)