Silicon on ferroelectric insulator field effect transistor (SOF-FET) a new device for the next generation ultra low power circuits

Title from PDF of title page, viewed on March 12, 2014Thesis advisor: Masud H. ChowdhuryVitaIncludes bibliographical references (pages 116-131)Thesis (M. S.)--School of Computer and Engineering. University of Missouri--Kansas City, 2013Field effect transistors (FETs) are the foundation for all electronic circuits and processors. These devices have progressed massively to touch its final steps in subnanometer level. Left and right proposals are coming to rescue this progress. Emerging nano-electronic devices (resonant tunneling devices, single-atom transistors, spin devices, Heterojunction Transistors rapid flux quantum devices, carbon nanotubes, and nanowire devices) took a vast share of current scientific research. Non-Si electronic materials like III-V heterostructure, ferroelectric, carbon nanotubes (CNTs), and other nanowire based designs are in developing stage to become the core technology of non-classical CMOS structures. FinFET present the current feasible commercial nanotechnology. The scalability and low power dissipation of this device allowed for an extension of silicon based devices. High short channel effect (SCE) immunity presents its major advantage. Multi-gate structure comes to light to improve the gate electrostatic over the channel. The new structure shows a higher performance that made it the first candidate to substitute the conventional MOSFET. The device also shows a future scalability to continue Moor’s Law. Furthermore, the device is compatible with silicon fabrication process. Moreover, the ultra-low-power (ULP) design required a subthreshold slope lower than the thermionic-emission limit of 60mV/ decade (KT/q). This value was unbreakable by the new structure (SOI-FinFET). On the other hand most of the previews proposals show the ability to go beyond this limit. However, those pre-mentioned schemes have publicized a very complicated physics, design difficulties, and process non-compatibility. The objective of this research is to discuss various emerging nano-devices proposed for ultra-low-power designs and their possibilities to replace the silicon devices as the core technology in the future integrated circuit. This thesis proposes a novel design that exploits the concept of negative capacitance. The new field effect transistor (FET) based on ferroelectric insulator named Silicon-On-Ferroelectric Insulator Field Effect Transistor (SOF-FET). This proposal is a promising methodology for future ultra-lowpower applications, because it demonstrates the ability to replace the silicon-bulk based MOSFET, and offers subthreshold swing significantly lower than 60mV/decade and reduced threshold voltage to form a conducting channel. The SOF-FET can also solve the issue of junction leakage (due to the presence of unipolar junction between the top plate of the negative capacitance and the diffused areas that form the transistor source and drain). In this device the charge hungry ferroelectric film already limits the leakage.Abstract -- List of illustrations - List of tables -- Acknowledgements -- Dedication -- Introduction -- Carbon nanotube field effect transistor -- Multi-gate transistors -FinFET -- Subthreshold swing -- Tunneling field effect transistors -- I-mos and nanowire fets -- Ferroelectric based field effect transistors -- An analytical model to approximate the subthreshold swing for soi-finfet -- Silicon-on-ferroelectric insulator field effect transistor (SOF-FET) -- Current-voltage characteristics of sof-fet -- Advantages, manufacturing process and future work of the proposed device -- Appendix -- Reference

Design, Modeling and Analysis of Non-classical Field Effect Transistors

Transistor scaling following per Moore\u27s Law slows down its pace when entering into nanometer regime where short channel effects (SCEs), including threshold voltage fluctuation, increased leakage current and mobility degradation, become pronounced in the traditional planar silicon MOSFET. In addition, as the demand of diversified functionalities rises, conventional silicon technologies cannot satisfy all non-digital applications requirements because of restrictions that stem from the fundamental material properties. Therefore, novel device materials and structures are desirable to fuel further evolution of semiconductor technologies. In this dissertation, I have proposed innovative device structures and addressed design considerations of those non-classical field effect transistors for digital, analog/RF and power applications with projected benefits. Considering device process difficulties and the dramatic fabrication cost, application-oriented device design and optimization are performed through device physics analysis and TCAD modeling methodology to develop design guidelines utilizing transistor\u27s improved characteristics toward application-specific circuit performance enhancement. Results support proposed device design methodologies that will allow development of novel transistors capable of overcoming limitation of planar nanoscale MOSFETs. In this work, both silicon and III-V compound devices are designed, optimized and characterized for digital and non-digital applications through calibrated 2-D and 3-D TCAD simulation. For digital functionalities, silicon and InGaAs MOSFETs have been investigated. Optimized 3-D silicon-on-insulator (SOI) and body-on-insulator (BOI) FinFETs are simulated to demonstrate their impact on the performance of volatile memory SRAM module with consideration of self-heating effects. Comprehensive simulation results suggest that the current drivability degradation due to increased device temperature is modest for both devices and corresponding digital circuits. However, SOI FinFET is recommended for the design of low voltage operation digital modules because of its faster AC response and better SCEs management than the BOI structure. The FinFET concept is also applied to the non-volatile memory cell at 22 nm technology node for low voltage operation with suppressed SCEs. In addition to the silicon technology, our TCAD estimation based on upper projections show that the InGaAs FinFET, with superior mobility and improved interface conditions, achieve tremendous drive current boost and aggressively suppressed SCEs and thereby a strong contender for low-power high-performance applications over the silicon counterpart. For non-digital functionalities, multi-fin FETs and GaN HEMT have been studied. Mixed-mode simulations along with developed optimization guidelines establish the realistic application potential of underlap design of silicon multi-Fin FETs for analog/RF operation. The device with underlap design shows compromised current drivability but improve analog intrinsic gain and high frequency performance. To investigate the potential of the novel N-polar GaN material, for the first time, I have provided calibrated TCAD modeling of E-mode N-polar GaN single-channel HEMT. In this work, I have also proposed a novel E-mode dual-channel hybrid MIS-HEMT showing greatly enhanced current carrying capability. The impact of GaN layer scaling has been investigated through extensive TCAD simulations and demonstrated techniques for device optimization

Modeling and Simulation of Subthreshold Characteristics of Short-Channel Fully-Depleted Recessed-Source/Drain SOI MOSFETs

Non-conventional metal-oxide-semiconductor (MOS) devices have attracted researchers‟ attention for future ultra-large-scale-integration (ULSI) applications since the channel length of conventional MOS devices approached the physical limit. Among the non-conventional CMOS devices which are currently being pursued for the future ULSI, the fully-depleted (FD) SOI MOSFET is a serious contender as the SOI MOSFETs possess some unique features such as enhanced short-channel effects immunity, low substrate leakage current, and compatibility with the planar CMOS technology. However, due to the ultra-thin source and drain regions, FD SOI MOSFETs possess large series resistance which leads to the poor current drive capability of the device despite having excellent short-channel characteristics. To overcome this large series resistance problem, the source/drain area may be increased by extending S/D either upward or downward. Hence, elevated-source/drain (E-S/D) and recessed-source/drain (Re-S/D) are the two structures which can be used to minimize the series resistance problem. Due to the undesirable issues such as parasitic capacitance, current crowding effects, etc. with E-S/D structure, the Re-S/D structure is a better choice. The FD Re-S/D SOI MOSFET may be an attractive option for sub-45nm regime because of its low parasitic capacitances, reduced series resistance, high drive current, very high switching speed and compatibility with the planar CMOS technology. The present dissertation is to deal with the theoretical modeling and computer-based simulation of the FD SOI MOSFETs in general, and recessed source/drain (Re-S/D) ultra-thin-body (UTB) SOI MOSFETs in particular. The current drive capability of Re-S/D UTB SOI MOSFETs can be further improved by adopting the dual-metal-gate (DMG) structure in place of the conventional single-metal-gate-structure. However, it will be interesting to see how the presence of two metals as gate contact changes the subthreshold characteristics of the device. Hence, the effects of adopting DMG structure on the threshold voltage, subthreshold swing and leakage current of Re-S/D UTB SOI MOSFETs have been studied in this dissertation. Further, high-k dielectric materials are used in ultra-scaled MOS devices in order to cut down the quantum mechanical tunneling of carriers. However, a physically thick gate dielectric causes fringing field induced performance degradation. Therefore, the impact of high-k dielectric materials on subthreshold characteristics of Re-S/D SOI MOSFETs needs to be investigated. In this dissertation, various subthreshold characteristics of the device with high-k gate dielectric and metal gate electrode have been investigated in detail. Moreover, considering the variability problem of threshold voltage in ultra-scaled devices, the presence of a back-gate bias voltage may be useful for ultimate tuning of the threshold voltage and other characteristics. Hence, the impact of back-gate bias on the important subthreshold characteristics such as threshold voltage, subthreshold swing and leakage currents of Re-S/D UTB SOI MOSFETs has been thoroughly analyzed in this dissertation. The validity of the analytical models are verified by comparing model results with the numerical simulation results obtained from ATLAS™, a device simulator from SILVACO Inc

Caractérisation électrique et modélisation du transport dans matériaux et dispositifs SOI avancés

This thesis is dedicated to the electrical characterization and transport modeling in advanced SOImaterials and devices for ultimate micro-nano-electronics. SOI technology is an efficient solution tothe technical challenges facing further downscaling and integration. Our goal was to developappropriate characterization methods and determine the key parameters. Firstly, the conventionalpseudo-MOSFET characterization was extended to heavily-doped SOI wafers and an adapted modelfor parameters extraction was proposed. We developed a nondestructive electrical method to estimatethe quality of bonding interface in metal-bonded wafers for 3D integration. In ultra-thin fully-depletedSOI MOSFETs, we evidenced the parasitic bipolar effect induced by band-to-band tunneling, andproposed new methods to extract the bipolar gain. We investigated multiple-gate transistors byfocusing on the coupling effect in inversion-mode vertical double-gate SOI FinFETs. An analyticalmodel was proposed and subsequently adapted to the full depletion region of junctionless SOI FinFETs.We also proposed a compact model of carrier profile and adequate parameter extraction techniques forjunctionless nanowires.Cette thèse est consacrée à la caractérisation et la modélisation du transport électronique dans des matériaux et dispositifs SOI avancés pour la microélectronique. Tous les matériaux innovants étudiés(ex: SOI fortement dopé, plaques obtenues par collage etc.) et les dispositifs SOI sont des solutions possibles aux défis technologiques liés à la réduction de taille et à l'intégration. Dans ce contexte,l'extraction des paramètres électriques clés, comme la mobilité, la tension de seuil et les courants de fuite est importante. Tout d'abord, la caractérisation classique pseudo-MOSFET a été étendue aux plaques SOI fortement dopées et un modèle adapté pour l'extraction de paramètres a été proposé. Nous avons également développé une méthode électrique pour estimer la qualité de l'interface de collage pour des plaquettes métalliques. Nous avons montré l'effet bipolaire parasite dans des MOSFET SOI totalement désertés. Il est induit par l’effet tunnel bande-à-bande et peut être entièrement supprimé par une polarisation arrière. Sur cette base, une nouvelle méthode a été développée pour extraire le gain bipolaire. Enfin, nous avons étudié l'effet de couplage dans le FinFET SOI double grille, en mode d’inversion. Un modèle analytique a été proposé et a été ensuite adapté aux FinFETs sans jonction(junctionless). Nous avons mis au point un modèle compact pour le profil des porteurs et des techniques d’extraction de paramètres

Reliability Investigations of MOSFETs using RF Small Signal Characterization

Modern technology needs and advancements have introduced various new concepts such as Internet-of-Things, electric automotive, and Artificial intelligence. This implies an increased activity in the electronics domain of analog and high frequency. Silicon devices have emerged as a cost-effective solution for such diverse applications. As these silicon devices are pushed towards higher performance, there is a continuous need to improve fabrication, power efficiency, variability, and reliability. Often, a direct trade-off of higher performance is observed in the reliability of semiconductor devices. The acceleration-based methodologies used for reliability assessment are the adequate time-saving solution for the lifetime's extrapolation but come with uncertainty in accuracy. Thus, the efforts to improve the accuracy of reliability characterization methodologies run in parallel. This study highlights two goals that can be achieved by incorporating high-frequency characterization into the reliability characteristics. The first one is assessing high-frequency performance throughout the device's lifetime to facilitate an accurate description of device/circuit functionality for high-frequency applications. Secondly, to explore the potential of high-frequency characterization as the means of scanning reliability effects within devices. S-parameters served as the high-frequency device's response and mapped onto a small-signal model to analyze different components of a fully depleted silicon-on-insulator MOSFET. The studied devices are subjected to two important DC stress patterns, i.e., Bias temperature instability stress and hot carrier stress. The hot carrier stress, which inherently suffers from the self-heating effect, resulted in the transistor's geometry-dependent magnitudes of hot carrier degradation. It is shown that the incorporation of the thermal resistance model is mandatory for the investigation of hot carrier degradation. The property of direct translation of small-signal parameter degradation to DC parameter degradation is used to develop a new S-parameter based bias temperature instability characterization methodology. The changes in gate-related small-signal capacitances after hot carrier stress reveals a distinct signature due to local change of flat-band voltage. The measured effects of gate-related small-signal capacitances post-stress are validated through transient physics-based simulations in Sentaurus TCAD.:Abstract Symbols Acronyms 1 Introduction 2 Fundamentals 2.1 MOSFETs Scaling Trends and Challenges 2.1.1 Silicon on Insulator Technology 2.1.2 FDSOI Technology 2.2 Reliability of Semiconductor Devices 2.3 RF Reliability 2.4 MOSFET Degradation Mechanisms 2.4.1 Hot Carrier Degradation 2.4.2 Bias Temperature Instability 2.5 Self-heating 3 RF Characterization of fully-depleted Silicon on Insulator devices 3.1 Scattering Parameters 3.2 S-parameters Measurement Flow 3.2.1 Calibration 3.2.2 De-embedding 3.3 Small-Signal Model 3.3.1 Model Parameters Extraction 3.3.2 Transistor Figures of Merit 3.4 Characterization Results 4 Self-heating assessment in Multi-finger Devices 4.1 Self-heating Characterization Methodology 4.1.1 Output Conductance Frequency dependence 4.1.2 Temperature dependence of Drain Current 4.2 Thermal Resistance Behavior 4.2.1 Thermal Resistance Scaling with number of fingers 4.2.2 Thermal Resistance Scaling with finger spacing 4.2.3 Thermal Resistance Scaling with GateWidth 4.2.4 Thermal Resistance Scaling with Gate length 4.3 Thermal Resistance Model 4.4 Design for Thermal Resistance Optimization 5 Bias Temperature Instability Investigation 5.1 Impact of Bias Temperature Instability stress on Device Metrics 5.1.1 Experimental Details 5.1.2 DC Parameters Drift 5.1.3 RF Small-Signal Parameters Drift 5.2 S-parameter based on-the-fly Bias Temperature Instability Characterization Method 5.2.1 Measurement Methodology 5.2.2 Results and Discussion 6 Investigation of Hot-carrier Degradation 6.1 Impact of Hot-carrier stress on Device performance 6.1.1 DC Metrics Degradation 6.1.2 Impact on small-signal Parameters 6.2 Implications of Self-heating on Hot-carrier Degradation in n-MOSFETs 6.2.1 Inclusion of Thermal resistance in Hot-carrier Degradation modeling 6.2.2 Convolution of Bias Temperature Instability component in Hot-carrier Degradation 6.2.3 Effect of Source and Drain Placement in Multi-finger Layout 6.3 Vth turn-around effect in p-MOSFET 7 Deconvolution of Hot-carrier Degradation and Bias Temperature Instability using Scattering parameters 7.1 Small-Signal Parameter Signatures for Hot-carrier Degradation and Bias Temperature Instability 7.2 TCAD Dynamic Simulation of Defects 7.2.1 Fixed Charges 7.2.2 Interface Traps near Gate 7.2.3 Interface Traps near Spacer Region 7.2.4 Combination of Traps 7.2.5 Drain Series Resistance effect 7.2.6 DVth Correction 7.3 Empirical Modeling based deconvolution of Hot-carrier Degradation 8 Conclusion and Recommendations 8.1 General Conclusions 8.2 Recommendations for Future Work A Directly measured S-parameters and extracted Y-parameters B Device Dimensions for Thermal Resistance Modeling C Frequency response of hot-carrier degradation (HCD) D Localization Effect of Interface Traps Bibliograph

Study of a New Silicon Epitaxy Technique: Confined Lateral Selective Epitaxial Growth

This work describes a significant new advance in the technique of silicon selective epitaxy called Confined Lateral Selective Epitaxial Growth (CLSEG). CLSEG is a method for forming thin films of single crystal silicon on top of an insulating layer or film. Such thin films are generically termed Silicon-On- Insulator (SOI), and1 allow dielectric isolation of integrated circuit elements, making them more efficient (faster with lower power), more resistant to radiation, and smaller than conventional integrated circuits, ionizing radiation than conventional integrated circuits. CLSEG offers advantages over current methods of achieving SOI by being easily manufactured, inherently reproducible, and having greater design flexibility. CLSEG is also adaptable to vertical stacking of devices in a circuit, in what is called three-dimensional integration, for even greater reductions in area. In addition, CLSEG can be used for a wide variety of sensor and micromachining application. This thesis describes the design and development of CLSEG, and compares it to the current state of the art in the fields of SOI and Selective Epitaxial Growth (SEG). CLSEG is accomplished by growing silicon selective epitaxy within a cavity; which is formed of dielectric materials upon a silicon substrate. The resulting SOI film can be made as thin as 0.1 micron, and tens of microns wide, with an unlimited length. In particular, there is now strong evidence that surface diffusivity of silicon adatoms on the dielectric masking layers is a significant contributor to the transport of silicon to the growth surface during SE G. CLSEG silicon material quality is evaluated by fabricating a variety of semiconductor devices in CLSEG films. These devices demonstrate the applicability of CLSEG to integrated circuits, and provide a basis of comparison between CLSEG-grown silicon and device-quality substrate silicon. Then, CLSEG is used to fabricate an advanced device structure, verifying the value and significance of this new epitaxy technique. In the final two chapters, CLSEG is evaluated as a technology, and compared to the current state of the art. Then, a method is presented Tor forming CLSEG with only one photolithography step, and a process is described for making a SOI film across an entire silicon wafer using CLSEG. These techniques may indicate the feasibility of using CLSEG for three dimensional integration of microelectronics. It is hoped that this work will establish a firm basis for further study of this interesting and valuable new technology

Evolution, Revolution, and Technology Scaling—The Impact on ESD and EOS Reliability

In the scaling of semiconductor devices, evolutionary and revolutionary modifications are made in the device dimension, structural changes, and dimensions. The effect of MOSFET scaling on electrostatic discharge (ESD) and electrical overstress (EOS) reliability and robustness have both positive and negative implications. In this publication, the evolutionary and revolutionary technology changes on how they influence the ESD and EOS results will be discussed in full detail. The paper will discuss changes in the substrate, wells, isolation, source/drain regions, gate dielectrics, inter-level dielectrics, and interconnects

Silicon on Ferroelectric Insulator Field Effect Transistor (SOFFET): A Radical Alternative to Overcome the Thermionic Limit

Title from PDF of title page viewed January 3,2018Dissertation advisor: Masud H ChowdhuryVitaIncludes bibliographical references (pages 165-180)Thesis (Ph.D.)--School of Computing and Engineering and Department of Physics and Astronomy. University of Missouri--Kansas City, 2016The path of down-scaling traditional MOSFET is reaching its technological, economic and, most importantly, fundamental physical limits. Before the dead-end of the roadmap, it is imperative to conduct a broad research to find alternative materials and new architectures to the current technology for the MOSFET devices. Beyond silicon electronic materials like group III-V heterostructure, ferroelectric material, carbon nanotubes (CNTs), and other nanowire-based designs are in development to become the core technology for non-classical CMOS structures. Field effect transistors (FETs) in general have made unprecedented progress in the last few decades by down-scaling device dimensions and power supply level leading to extremely high numbers of devices in a single chip. High density integrated circuits are now facing major challenges related to power management and heat dissipation due to excessive leakage, mainly due to subthreshold conduction. Over the years, planar MOSFET dimensional reduction was the only process followed by the semiconductor industry to improve device performance and to reduce the power supply. Further scaling increases short-channel-effect (SCE), and off-state current makes it difficult for the industry to follow the well-known Moore’s Law with bulk devices. Therefore, scaling planar MOSFET is no longer considered as a feasible solution to extend this law. The down-scaling of metal-oxide-semiconductor field effect transistors (MOSFETs) leads to severe short-channel-effects and power leakage at large-scale integrated circuits (LSIs). The device, which is governed by the thermionic emission of the carriers injected from the source to the channel region, has set a limitation of the subthreshold swing (S) of 60 / at room temperature. Devices with ‘S’ below this limit is highly desirable to reduce the power consumption and maintaining a high / current ratio. Therefore, the future of semiconductor industry hangs on new architectures, new materials or even new physics to govern the flow of carriers in new switches. As the subthreshold swing is increasing at every technology node, new structures using SOI, multi-gate, nanowire approach, and new channel materials such as III–V semiconductor have not satisfied the targeted values of subthreshold swing. Moreover, the ultra-low-power (ULP) design required a subthreshold slope lower than the thermionic emission limit of 60 /. This value was unbreakable by the new structure (SOI FinFET). On the other hand, most of the preview proposals show the ability to go beyond this limit. However, those pre-mentioned schemes have publicized very complicated physics, design difficulties, and process non-compatibility. The objective of this research is to discuss various emerging nano-devices proposed for sub-60 mV/decade designs and their possibilities to replace the silicon devices as the core technology in the future integrated circuit. This dissertation also proposes a novel design that exploits the concept of negative capacitance. The new field-effect-transistor (FET) based on ferroelectric insulator named Silicon-On-Ferroelectric Insulator Field effect-transistor (SOFFET). This proposal is a promising methodology for future ultra low-power applications because it demonstrates the ability to replace the silicon-bulk based MOSFET, and offers a subthreshold swing significantly lower than 60 / and reduced threshold voltage to form a conducting channel. The proposed SOFFET design, which utilizes the negative capacitance of a ferroelectric insulator in the body-stack, is completely different from the FeFET and NCFET designs. In addition to having the NC effect, the proposed device will have all the advantages of an SOI device. Body-stack that we are intending in this research has many advantages over the gate-stack. First, it is more compatible with the existing processes. Second, the gate and the working area of the proposed SOFFET is like the planar MOSFET. Third, the complexity and ferroelectric material interferences are shifted to the body of the device from the gate and the working area. The proposed structure offers better scalability and superior constructability because of the high-dielectric buried insulator. Here we are providing a very simplified model for the structure. Silicon-on-ferroelectric leads to several advantages including low off-state current and shift in the threshold voltage with the decrease of the ferroelectric material thickness. Moreover, having an insulator in the body of the device increases the controllability over the channel, which leads to the reduction in the short-channel-effect (SCE). The proposed SOFFET offers low value of subthreshold swing (S) leading to better performance in the on-state. The off-state current is directly related to S. So, the off-state current is also minimum in the proposed structure.Introduction -- Subthreshold swing -- Multi-gate devices -- Tunneling field effect transistors -- I-mos & FET transistors -- Ferroelectric based field effect transistors -- An analytical model to approximate the subthreshold swing for SOI-FINFET -- Multichannel tunneling carbon nanotube FET -- Partially depleted silicon-on-Ferroelectric insulator FET -- Fully depleted silicon-on-ferroelectric insulator FET -- Advantages, manufacturing process, and future work of the proposed devices -- Appendix A. Estimation of the body factor (n) [eta] of SOI FinFET -- Appendix B. Solution for the Poisson Equation of MT-CNTFE