Design and demonstration of digital pre-distortion using software defined radio

Abstract. High data rates for large number of users set tight requirements for signal quality measured in terms of error vector magnitude (EVM). In radio transmitters, nonlinear distortion dominated by power amplifiers (PAs) often limits the achievable EVM. However, the linearity can be improved by linearization techniques. Digital pre-distortion (DPD) is one of these widely used linearization techniques for an effective distortion reduction over a wide bandwidth. In DPD, the nonlinearity of the transmitter is pre-compensated in the digital domain to achieve linear output. Moreover, DPD is used to enable PAs to operate in the power-efficient region with a decent linearity. As we are moving towards millimetre-wave frequencies to enable the wideband communications, the design of the DPD algorithm must be optimized in terms of performance and power consumption. Moreover, continuous development of wireless infrastructure motivates to make research on programmable and reconfigurable platforms in order to decrease the demonstration cost and time, especially for the demonstration purposes. This thesis illustrates and presents how software defined radio (SDR) platforms can be used to demonstrate DPD. Universal software defined peripheral (USRP) X300 is a commercial software defined radio (SDR) platform. The chosen model, X300, has two independent channels equipped with individual transceiver cards. SIMULINK is used to communicate with the device and the two channels of X300 are used as transmitter and receiver simultaneously in full-duplex mode. Hence, a single USRP device is acting as an operational transmitter and feedback receiver, simultaneously. The implemented USRP design consists of SIMULINK based transceiver design and lookup table based DPD in which the coefficients are calculated in MATLAB offline. An external PA, i.e. ZFL-2000+ together with a directional coupler and attenuator are connected between the TX/RX port and RX2 port to measure the nonlinearity. The nonlinearity transceiver is measured with and without the external PA. The experimental results show decent performance for linearization by using the USRP platform. However, the results differ widely due to the used USRP transceiver parameterization and PA operational point. The 16 QAM test signal with 500 kHz bandwidth is fed to the USRP transmit chain. As an example, the DPD algorithm improves the EVM from 7.6% to 2.1% and also the ACPR is reduced around 10 dB with the 16 QAM input signal where approximately + 2.2 dBm input power applied to the external PA

Space Shuttle/TDRSS communication and tracking systems analysis

In order to evaluate the technical and operational problem areas and provide a recommendation, the enhancements to the Tracking and Data Delay Satellite System (TDRSS) and Shuttle must be evaluated through simulation and analysis. These enhancement techniques must first be characterized, then modeled mathematically, and finally updated into LinCsim (analytical simulation package). The LinCsim package can then be used as an evaluation tool. Three areas of potential enhancements were identified: shuttle payload accommodations, TDRSS SSA and KSA services, and shuttle tracking system and navigation sensors. Recommendations for each area were discussed

Space station tracking requirements feasibility study, volume 2

The objective of this feasibility study is to determine analytically the accuracies of various sensors being considered as candidates for Space Station use. Specifically, the studies were performed whether or not the candidate sensors are capable of providing the required accuracy, or if alternate sensor approaches should be investigated. Other topics related to operation in the Space Station environment were considered as directed by NASA-JSC. The following topics are addressed: (1) Space Station GPS; (2) Space Station Radar; (3) Docking Sensors; (4) Space Station Link Analysis; (5) Antenna Switching, Power Control, and AGC Functions for Multiple Access; (6) Multichannel Modems; (7) FTS/EVA Emergency Shutdown; (8) Space Station Information Systems Coding; (9) Wanderer Study; and (10) Optical Communications System Analysis. Brief overviews of the abovementioned topics are given. Wherever applicable, the appropriate appendices provide detailed technical analysis. The report is presented in two volumes. This is Volume 2, containing Appendices K through U

Digital Pre-distortion for Interference Reduction in Dynamic Spectrum Access Networks

Given the ever increasing reliance of today’s society on ubiquitous wireless access, the paradigm of dynamic spectrum access (DSA) as been proposed and implemented for utilizing the limited wireless spectrum more efficiently. Orthogonal frequency division multiplexing (OFDM) is growing in popularity for adoption into wireless services employing DSA frame- work, due to its high bandwidth efficiency and resiliency to multipath fading. While these advantages have been proven for many wireless applications, including LTE-Advanced and numerous IEEE wireless standards, one potential drawback of OFDM or its non-contiguous variant, NC-OFDM, is that it exhibits high peak-to-average power ratios (PAPR), which can induce in-band and out-of-band (OOB) distortions when the peaks of the waveform enter the compression region of the transmitter power amplifier (PA). Such OOB emissions can interfere with existing neighboring transmissions, and thereby severely deteriorate the reliability of the DSA network. A performance-enhancing digital pre-distortion (DPD) technique compensating for PA and in-phase/quadrature (I/Q) modulator distortions is proposed in this dissertation. Al- though substantial research efforts into designing DPD schemes have already been presented in the open literature, there still exists numerous opportunities to further improve upon the performance of OOB suppression for NC-OFDM transmission in the presence of RF front-end impairments. A set of orthogonal polynomial basis functions is proposed in this dissertation together with a simplified joint DPD structure. A performance analysis is presented to show that the OOB emissions is reduced to approximately 50 dBc with proposed algorithms employed during NC-OFDM transmission. Furthermore, a novel and intuitive DPD solution that can minimize the power regrowth at any pre-specified frequency in the spurious domain is proposed in this dissertation. Conventional DPD methods have been proven to be able to effectively reduce the OOB emissions that fall on top of adjacent channels. However more spectral emissions in more distant frequency ranges are generated by employing such DPD solutions, which are potentially in violation of the spurious emission limit. At the same time, the emissions in adjacent channel must be kept under the OOB limit. To the best of the author’s knowledge, there has not been extensive research conducted on this topic. Mathematical derivation procedures of the proposed algorithm are provided for both memoryless nonlinear model and memory-based nonlinear model. Simulation results show that the proposed method is able to provide a good balance of OOB emissions and emissions in the far out spurious domain, by reducing the spurious emissions by 4-5 dB while maintaining the adjacent channel leakage ratio (ACLR) improvement by at least 10 dB, comparing to the PA output spectrum without any DPD

Shuttle Communications and Tracking Systems Modeling and TDRSS Link Simulations Studies

An analytical simulation package (LinCsim) which allows the analytical verification of data transmission performance through TDRSS satellites was modified. The work involved the modeling of the user transponder, TDRS, TDRS ground terminal, and link dynamics for forward and return links based on the TDRSS performance specifications (4) and the critical design reviews. The scope of this effort has recently been expanded to include the effects of radio frequency interference (RFI) on the bit error rate (BER) performance of the S-band return links. The RFI environment and the modified TDRSS satellite and ground station hardware are being modeled in accordance with their description in the applicable documents

Techniques for nonlinear distortion suppression in radio over fiber communication systems

Radio over fiber (RoF) is a promising technology that will indisputably compete as a viable solution for future wireless, cellular and broadband networks. RoF, when combined with dense wavelength division multiplexing (DWDM), such as SONET/SDH, it can become a complete flexible and cost effective solution to the global telecommunication network, where asynchronous and synchronous communications may be efficiently supported. Subcarrier modulation (SCM) is utilized to modulate a RF signal on light, which in turn will be transmitted by fiber. Unfortunately, the transmission in most cases may become corrupted by nonlinear distortion that is induced by the nonlinear response of the optical transmitter, optical receiver and chromatic dispersion of the single mode fiber (SMF). The nonlinear distortion degrades the receiver sensitivity, which leads to a poor bit error rate (BER) and spurious free dynamic range (SFDR). Ultimately, this will increase RoF system costs and render it impractical. The objective of this thesis is to develop linearization methods that reduce the nonlinear distortion, increase receiver sensitivity and increase SFDR. The designs should also address the entire RoF system by combating the optical power fading issue that will be discussed in Chapter 2 without significantly adding great expense and complexity to the RoF system. Four optical linearization methods are proposed and shown through extensive simulation and/or experimentation to outperform similar existing linearization systems described in literature. The proposed single wavelength balanced system is shown to improve the suppression of 2nd order distortion over the dual wavelength balanced system, thereby leading to greater improvement in receiver sensitivity and BER. Furthermore, the design also suppresses relative intensity noise (RIN). The proposed tunable fiber Bragg grating (FBG) balanced system is capable of suppressing both 2 nd and 3 rd order distortions despite which RF carrier that is used. Furthermore, it was shown to outperform the conventional RoF system in terms of receiver sensitivity and BER. The proposed asymmetric Mach-Zehnder modulator (MZM) has been shown to generate optical single sideband (OSSB) transmissions and outperform the dual-parallel modulator, by improving 3rd order intermodulation distortion (3IMD) suppression and increasing SFDR. The final proposed linearization method is the mixed-polarization MZM, where OSSB is also generated and outperforms the conventional OSSB RoF system in terms of 3IMD suppression and SFDR. Furthermore, close form expressions for SFDR are developed for the final two designs, which is crucial in study of their stability and performance

Adaptive optical feedforward linearization of optical transceiver for radio over fiber communication link

With the tremendous growth in numbers of mobile data subscribers and explosive demand for mobile data, the current wireless access network need to be augmented in order to keep up with the data speed promised by the future generation mobile network standards. Radio over fiber technology (RoF) is a cost effective solution because of its ability to support numerous numbers of simple structured base stations by consolidating the signal processing functions at the central station. RoF systems are analog systems where noise figure and spurious free dynamic range (SFDR) are important parameters in an RoF link. The nonlinearity of a laser transmitter is a major limiting factor to the performance of an RoF link, as it generates spurious spectral components, leading to intermodulation distortions (IMD), which limit the achievable SFDR of the analog RF wave transmissions. The device nonlinearity can be mitigated through various linearization schemes. The feedforward linearization technique offers a number of advantages compared to other techniques, as it offers good suppression of distortion products over a large bandwidth and supports high operating frequencies. On the other hand, feedforward linearization is a relatively sensitive scheme, where its performance is highly influenced by changing operating conditions such as laser aging, temperature effect, and input signal variations. Therefore, for practical implementations the feedforward system has to be real-time adaptive. This thesis aims to develop an adaptive optical feedforward linearization system for radio over fiber links. Mathematical analyses and computer simulations are performed to determine the most efficient algorithm for the adaptive controller for laser transmitter feedforward linearization system. Experimental setup and practical measurement are performed for an adaptive feedforward linearized laser transmitter and its performance is optimized. The adaptive optical feedforward linearization system has been modeled and simulated in MATLAB Simulink. The performances of two adaptive algorithms, which are related to the gradient signal method, such as least mean square (LMS) and recursive least square (RLS) have been compared. The LMS algorithm has been selected because of its robustness and simplicity. Finally, the adaptive optical feedforward linearization system has been set up with digital signal processor (DSP) as the control device, and practical measurement has been performed. The system has achieved a suppression of 14 dB in the third order IMD products over a bandwidth of 30 MHz, in a two-tone measurement at 1.7 GHz

Radio Frequency Interference Impact Assessment on Global Navigation Satellite Systems

The Institute for the Protection and Security of the Citizen of the EC Joint Research Centre (IPSC-JRC) has been mandated to perform a study on the Radio Frequency (RF) threat against telecommunications and ICT control systems. This study is divided into two parts. The rst part concerns the assessment of high energy radio frequency (HERF) threats, where the focus is on the generation of electromagnetic pulses (EMP), the development of corresponding devices and the possible impact on ICT and power distribution systems. The second part of the study concerns radio frequency interference (RFI) with regard to global navigation satellite systems (GNSS). This document contributes to the second part and contains a detailed literature study disclosing the weaknesses of GNSS systems. Whereas the HERF analysis only concerns intentional interference issues, this study on GNSS also takes into account unintentional interference, enlarging the spectrum of plausible interference scenarios.JRC.DG.G.6-Security technology assessmen

Optical free space feedforward non-linearity correction system

Recent years have seen unprecedented growth in the popularity and deployment of mobile phones. As this continues, so the strain on existing mobile cellular radio network has also increased, leading to the need to investigate new technologies to relieve this pressure. The problem is being further exacerbated by the introduction of the 3rd generation of mobile communications, otherwise known as UMTS (Universal Mobile Telecommunications System), with the aim of offering multimedia services on pocket sized portable receivers. A major cost of the mobile radio network, in terms of both financial and social/environmental aspects, is the need apparent need for more base transceiver stations (BTS), due to the increased number of services, and the density of them. Therefore, judicious use of fewer, but more "intelligent" base stations, thereby reducing the overall system costs, and extra flexibility in the design of mobile cells would be desirable. This can be achieved by having the BTS antennas remotely positioned from the BTS by transmitting the radio signals down an optical fibre or, as in this project, over free space. The main application for this is in densely urban heavy use areas, where there is extensive reuse of both cell and cell cluster. This, along with building shadowing, would require a BTS on every corner, and where extra cell design flexibility would be desirable. Also, in remote rural areas, where various natural features, such as rivers or mountains can cause similar cell design problems, there is a need for this flexibility. The problem with this requirement is that the electrical to optical conversion process, involving a laser diode driver unit, is inherently non-linear, and, unless this is resolved, the desired signal will become unusable due to distortion. To overcome these nonlinearities, a novel correction may be used, based on an optical feedforward correction technique. The prototype system employs off-the-shelf components, and has one Fabry Perot laser diode (FP-LD) providing two signals (via a beam splitter), for a main path and one for the error path loop. The error path signal is detected by a receiver circuit, then mixed with a reference signal to produce a 'pure' error signal, which then modulates the second FP-LD. In contrast with previous fibre feedforward systems, where the two LD outputs are then combined in the optical fibre pre-reception, this system has to combine the signals post-reception. After the main signal and error signal are received and recombined, the non-linearities of the main path are predominantly cancelled by those present in the error path signal, leaving only the desired signal, free of non-linearities

CMOS RF front-end design for terrestrial and mobile digital television systems

With the increasing demand for high quality TV service, digital television (DTV) is replacing the conventional analog television. DTV tuner is one of the most critical blocks of the DTV receiver system; it down-converts the desired DTV RF channel to baseband or a low intermediate frequency with enough quality. This research is mainly focused on the analysis and realization of low-cost low-power front-ends for ATSC terrestrial DTV and DVB-H mobile DTV tuner systems. For the design of the ATSC terrestrial tuner, a novel double quadrature tuner architecture, which can not only minimize the tuner power consumption but also achieve the fully integration, has been proposed. A double quadrature down-converter has been designed and fabricated with TSMC 0.35õm CMOS technology; the measurement results verified the proposed concepts. For the mobile DTV tuner, a zero-IF architecture is used and it can achieve the DVB-H specifications with less than 200mW power consumption. In the implementation of the mobile DVB-H tuner, a novel RF variable gain amplifier (RFVGA) and a low flicker noise current-mode passive mixer have been proposed. The proposed RFVGA achieves high dynamic range and robust input impedance matching performance, which is the main design challenge for the traditional implementations. The current-mode passive mixer achieves high-gain, low noise (especially low flicker noise) and high-linearity (over 10dBm IIP3) with low power supplies; it is believed that this is a promising topology for low voltage high dynamic range mixer applications. The RFVGA has been fabricated in TSMC 0.18õm CMOS technology and the measurement results agree well with the theoretical ones