1,411 research outputs found

    A Single-Stage LED Driver Based on ZCDS Class-E Current-Driven Rectifier as a PFC for Street-Lighting Applications

    Get PDF
    This paper presents a light-emitting diode (LED) driver for street-lighting applications that uses a resonant rectifier as a power-factor corrector (PFC). The PFC semistage is based on a zero-current and zero-derivative-switching (ZCDS) Class-E current-driven rectifier, and the LED driver semistage is based on a zero-voltage-switching (ZVS) Class-D LLC resonant converter that is integrated into a single-stage topology. To increase the conduction angle of the bridge-rectifier diodes current and to decrease the current harmonics that are injected in the utility line, the ZCDS Class-E rectifier is placed between the bridge-rectifier and a dc-link capacitor. The ZCDS Class-E rectifieris driven by a high-frequency current source, which is obtained from a square-wave output voltage of the ZVS Class-D LLC resonant converter using a matching network. Additionally, the proposed converter has a soft-switching characteristic that reduces switching losses and switching noise. A prototype for a 150-W LED street light has been developed and tested to evaluate the performance of the proposed approach. The proposed LED driver had a high efficiency (>91%), a high PF (>0.99), and a low total harmonic distortion (THD i <; 8%) under variation of the utility-line input voltage from 180 to 250 V rms . These experimental results demonstrate the feasibility of the proposed LED scheme

    State-variable modelling of CLL resonant converters

    Get PDF
    The paper presents the derivation and application of state-variable models to high-order topologies of resonant converters. In particular, a 3rd order CLL resonant circuit is considered with bridge rectification and both a capacitive output filter (voltage output), and an LC output filter (current output). The state-variable model accuracy is verified against component-based simulation packages (Spice) and practical measurements, and it is shown that the resulting models facilitate rapid analysis compared to their integration-based counterparts (Spice, Saber), without the loss of accuracy normally associated with fundamental mode approximation (FMA) techniques. Moreover, unlike FMA, the models correctly predict the resonant peaks associated with harmonic excitation of the tank resonance. Subsequently, it is shown that excitation of the resonant tank by odd harmonics of the input voltage can be utilised to provide overcurrent protection in the event of an output short-circuit. Further, through judicious control of operating frequency, it is shown that 'inductive' zero voltage switching (ZVS) can still be obtained, facilitating reductions in gate-drive switching losses, thereby improving efficiency and thermal management of the supply under fault conditions. Although the results are ultimately generic to other converter counterparts, measured results from two prototype 36 V input, 11-14.4V output, 3rd - order CLL converters are included to practically demonstrate the attributes of the proposed analysis and control schemes

    Analysis and control of dual-output LCLC resonant converters with significant leakage inductance

    Get PDF
    The analysis, design and control of fourth-order LCLC voltage-output series-parallel resonant converters for the provision of multiple regulated outputs, is described. Specifically, state-variable concepts are developed to establish operating mode boundaries with which to describe the internal behavior and the impact of output leakage inductance. The resulting models are compared with those obtained from SPICE simulations and measurements from a prototype power supply under closed loop control to verify the analysis, modeling, and control predictions

    A comparative study of different optimization methods for resonance half-bridge converter

    Get PDF
    The LLC resonance half-bridge converter is one of the most popular DC-DC converters and could easily inspire researchers to design a high-efficiency and high-power-density converter. LLC resonance converters have diverse operation modes based on switching frequency and load that cause designing and optimizing procedure to vary in different modes. In this paper, different operation modes of the LLC half-bridge converter that investigate different optimization procedures are introduced. The results of applying some usual optimization methods implies that for each operation mode some specific methods are more appropriate to achieve high efficiency. To verify the results of each optimization, numerous simulations are done by Pspice and MATLAB and the efficiencies are calculated to compare them. Finally, to verify the result of optimization, the experimental results of a laboratory prototype are provided.Peer ReviewedPostprint (published version

    Linearized large signal modeling, analysis, and control design of phase-controlled series-parallel resonant converters using state feedback

    Get PDF
    This paper proposes a linearized large signal state-space model for the fixed-frequency phase-controlled series-parallel resonant converter. The proposed model utilizes state feedback of the output filter inductor current to perform linearization. The model combines multiple-frequency and average state-space modeling techniques to generate an aggregate model with dc state variables that are relatively easier to control and slower than the fast resonant tank dynamics. The main objective of the linearized model is to provide a linear representation of the converter behavior under large signal variation which is suitable for faster simulation and large signal estimation/calculation of the converter state variables. The model also provides insight into converter dynamics as well as a simplified reduced order transfer function for PI closed-loop design. Experimental and simulation results from a detailed switched converter model are compared with the proposed state-space model output to verify its accuracy and robustness

    A Current-Dependent Switching Strategy for Si/SiC Hybrid Switch-Based Power Converters

    Get PDF
    Abstract: Hybrid switches configured by paralleling Silicon (Si) Insulated Gate Bipolar Transistors (IGBT) and Silicon Carbide (SiC) Metal-Oxide Semiconductor Field-Effect Transistors (MOSFET) have been verified to be a high-efficiency cost-effective device concept. In this paper, a current-dependent switching strategy is introduced and implemented to further improve the performance of Si/SiC hybrid switches. This proposed switching strategy is based on a comprehensive consideration of reducing device losses, reliable operation, and overload capability. Based on the utilization of such Si/SiC hybrid switches and the proposed switching strategy, a 15-kW single-phase H-bridge inverter prototype was implemented and tested in the laboratory. Simulation and experimental results are given to verify the performance of the hybrid switches and the new switching strategy

    Optimized power converters for electrically augmented on-orbit propulsion systems

    Full text link
    Advances in satellite thruster technology have produced the requirement for high power electrical supplies to operate electrically augmented on-orbit propulsion systems. The power on board satellites is greatly limited by the solar panels that collect energy and the batteries that store the energy. In addition, satellites are constantly using power to operated their mission equipment and handle the communication requirements; This thesis investigates the power systems of modern satellites and the addition of an on-orbit electrically augmented propulsion system. The research process involves determining the system specifications, the power available and the thruster requirements. After determining the requirements, the implementation of the electrically augmented on-orbit propulsion system is characterized in terms of efficiency and potential electromagnetic compatibility. Several circuits are evaluated with the aid of PSPICE circuit simulation software and the results of the evaluation criteria for each circuit are presented

    Predictive voltage control of phase-controlled series-parallel resonant converter

    Get PDF

    Digital control of dual-load LCLC resonant converters

    Get PDF
    The paper proposes the analysis, design and realisation of dual-output resonant LCLC converters with independent output regulation, employing a single power stage and combined PWM and frequency control. Asymmetric switching of the power devices is used to facilitate independent control of the outputs to provide +5 V and +3.3 V from a 15 V-20 V input supply over a range of load condition
    corecore