189 research outputs found
Recommended from our members
Design Techniques for High-Performance SAR A/D Converters
The design of electronics needs to account for the non-ideal characteristics of the device technologies used to realize practical circuits. This is particularly important in mixed analog-digital design since the best device technologies are very different for digital compared to analog circuits. One solution for this problem is to use a calibration correction approach to remove the errors introduced by devices, but this adds complexity and power dissipation, as well as reducing operation speed, and so must be optimised. This thesis addresses such an approach to improve the performance of certain types of analog-to-digital converter (ADC) used in advanced telecommunications, where speed, accuracy and power dissipation currently limit applications. The thesis specifically focuses on the design of compensation circuits for use in successive approximation register (SAR) ADCs.
ADCs are crucial building blocks in communication systems, in general, and for mobile networks, in particular. The recently launched fifth generation of mobile networks (5G) has required new ADC circuit techniques to meet the higher speed and lower power dissipation requirements for 5G technology. The SAR has become one of the most favoured architectures for designing high-performance ADCs, but the successive nature of the circuit operation makes it difficult to reach ∼GS/s sampling rates at reasonable power consumption.
Here, two calibration techniques for high-performance SAR ADCs are presented. The first uses an on-chip stochastic-based mismatch calibration technique that is able to accurately compute and compensate for the mismatch of a capacitive DAC in a SAR ADC. The stochastic nature of the proposed calibration method enables determination of the mismatch of the CAPDAC with a resolution much better than that of the DAC. This allows the unit capacitor to scale down to as low as 280aF for a 9-bit DAC. Since the CAP-DAC causes a large part of the overall dynamic power consumption and directly determines both the sizes of the driving and sampling switches and the size of the input capacitive load of the ADC and the kT/C noise power, a small CAP-DAC helps the power efficiency. To validate the proposed calibration idea, a 10-bit asynchronous SAR ADC was fabricated in 28-nm CMOS. Measurement results show that the proposed stochastic calibration improves the ADC’s SFDR and SNDR by 14.9 dB, 11.5 dB, respectively. After calibration, the fabricated SAR ADC achieves an ENOB of 9.14 bit at a sampling rate of 85 MS/s, resulting in a Walden FoM of 10.9 fJ/c-s.
The second calibration technique is a timing-skew calibration for a time-interleaved (TI) SAR ADC that calibrates/computes the inter-channel timing and offset mismatch simultaneously. Simulation results show the effectiveness of this calibration method. When used together, the proposed mismatch calibration technique and the timing-skew
calibration technique enables a TI SAR ADC to be designed that can achieve a sampling rate of ∼GS/s with 10-bit resolution and a power consumption as low as ∼10mW; specifications that satisfy the requirements of 5G technology
Public key cryptosystems : theory, application and implementation
The determination of an individual's right to privacy is mainly a nontechnical matter, but the pragmatics of providing it is the central concern of the cryptographer. This thesis has sought answers to some of the outstanding issues in cryptography. In particular, some of the theoretical, application and implementation problems associated with a Public Key Cryptosystem (PKC).The Trapdoor Knapsack (TK) PKC is capable of fast throughput, but suffers from serious disadvantages. In chapter two a more general approach to the TK-PKC is described, showing how the public key size can be significantly reduced. To overcome the security limitations a new trapdoor was described in chapter three. It is based on transformations between the radix and residue number systems.Chapter four considers how cryptography can best be applied to multi-addressed packets of information. We show how security or communication network structure can be used to advantage, then proposing a new broadcast cryptosystem, which is more generally applicable.Copyright is traditionally used to protect the publisher from the pirate. Chapter five shows how to protect information when in easily copyable digital format.Chapter six describes the potential and pitfalls of VLSI, followed in chapter seven by a model for comparing the cost and performance of VLSI architectures. Chapter eight deals with novel architectures for all the basic arithmetic operations. These architectures provide a basic vocabulary of low complexity VLSI arithmetic structures for a wide range of applications.The design of a VLSI device, the Advanced Cipher Processor (ACP), to implement the RSA algorithm is described in chapter nine. It's heart is the modular exponential unit, which is a synthesis of the architectures in chapter eight. The ACP is capable of a throughput of 50 000 bits per second
The Fifth NASA Symposium on VLSI Design
The fifth annual NASA Symposium on VLSI Design had 13 sessions including Radiation Effects, Architectures, Mixed Signal, Design Techniques, Fault Testing, Synthesis, Signal Processing, and other Featured Presentations. The symposium provides insights into developments in VLSI and digital systems which can be used to increase data systems performance. The presentations share insights into next generation advances that will serve as a basis for future VLSI design
Concurrent Error Detection in Finite Field Arithmetic Operations
With significant advances in wired and wireless technologies and also increased shrinking in the size of VLSI circuits, many devices have become very large because they need to contain several large units. This large number of gates and in turn large number of transistors causes the devices to be more prone to faults. These faults specially in sensitive and critical applications may cause serious failures and hence should be avoided.
On the other hand, some critical applications such as cryptosystems may also be prone to deliberately injected faults by malicious attackers. Some of these faults can produce erroneous results that can reveal some important secret information of the cryptosystems. Furthermore, yield factor improvement is always an important issue in VLSI design and fabrication processes. Digital systems such as cryptosystems and digital signal processors usually contain finite field operations. Therefore, error detection and correction of such operations have become an important issue recently.
In most of the work reported so far, error detection and correction are applied using redundancies in space (hardware), time, and/or information (coding theory). In this work, schemes based on these redundancies are presented to detect errors in important finite field arithmetic operations resulting from hardware faults. Finite fields are used in a number of practical cryptosystems and channel encoders/decoders. The schemes presented here can detect errors in arithmetic operations of finite fields represented in different bases, including polynomial, dual and/or normal basis, and implemented in various architectures, including bit-serial, bit-parallel and/or systolic arrays
Recommended from our members
Development of a Portable CMOS Time-Domain Fluorescence Lifetime Imager
Modern laboratory equipments to measure the excited-state lifetime of fluorophores usually include an expensive picosecond pulsed-laser excitation source, a fragile photomultiplier tube, and a large instrument body for optics. A portable and robust device to make fluorescence lifetime measurement in nanosecond scale is of great attraction for chemists and biologists.
This dissertation reports the development of a portable LED time-domain fluorimeter from an all-solid-state discrete-component prototype to its advanced CMOS integrated circuit implementation. The motivation of the research is to develop a multiplexed fluorimeter for point-of-care diagnosis. Instruments developed by this novel method have higher fill factor, are more portable, and are fabricated at lower cost
Rules for modelling in computer-aided fault tree synthesis
In the design of process plants safety has assumed an increasingly high profile. One of the
techniques used in hazard identification is the fault tree, which involves first the synthesis of
the tree and then its analysis. The construction of a fault tree, however, requires special
skills and can be a time-consuming process. It is therefore attractive to develop computer
aids for the synthesis stage to match those which already exist for the analysis of the tree.
A computer based system for fault tree synthesis has been developed at Loughborough
University. This thesis is part of a continuing programme of work associated with this facility. [Continues.
Feasibility study for a scanning celestial attitude determination system SCADS on the IMP spacecraft Final report
System design analysis to establish feasibility of using electro-optical celestial scanning sensor on IMP spacecraft for determination of spacecraft attitude by star measurement
Design and application of convergent cellular automata
Systems made of many interacting elements may display unanticipated emergent properties. A system for which the desired properties are the same as those which emerge will be inherently robust. Currently available techniques for designing emergent properties are prohibitively costly for all but the simplest systems.
The self-assembly of biological cells into tissues and ultimately organisms is an example of a natural dynamic distributed system of which the primary emergent behaviour is a fully operational being. The distributed process that co-ordinates this self-assembly is morphogenesis. By analysing morphogenesis with a cellular automata model we deduce a means by which this self-organisation might be achieved.
This mechanism is then adapted to the design of self-organising patterns, reliable electronic systems and self-assembling systems. The limitations of the design algorithm are analysed, as is a means to overcome them. The cost of this algorithm is discussed and finally demonstrated with the design of a reliable arithmetic logic unit and a self-assembling, self-repairing and metamorphosising robot made of 12,000 cells
Fault tolerant programmable digital attitude control electronics study
The attitude control electronics mechanization study to develop a fault tolerant autonomous concept for a three axis system is reported. Programmable digital electronics are compared to general purpose digital computers. The requirements, constraints, and tradeoffs are discussed. It is concluded that: (1) general fault tolerance can be achieved relatively economically, (2) recovery times of less than one second can be obtained, (3) the number of faulty behavior patterns must be limited, and (4) adjoined processes are the best indicators of faulty operation
- …