20 research outputs found

    Analysis and design of UHF and millimetre wave radio frequency identification

    Get PDF
    Radio frequency identification (RFID) is an asymmetric radio protocol, where uplink communication (from transponder to reader) is implemented with backscattering modulation. The idea was first demonstrated in the 1940's. One of the first consumer applications of RFID was access control, and key cards based on an inductive near field coupling are widely used even today. The introduction of Schottky diodes to CMOS processes enabled passive RFID, i.e. transponders without a battery, at ultra high frequencies (UHF) with reasonable cost and read range in the end of 1990's. This has opened up new applications and inspired new research on RFID. This thesis studies the radio frequency (RF) components and general RF phenomena in RFID at UHF and millimetre waves. The theoretical analysis of the radio path reveals that the read range of a passive UHF system is ideally limited by the downlink, i.e. the power transfer from reader to the transponder. However, the architecture of the reader RF front end is critical, because the transmitted signal may couple a significant amount of noise to the receiver, overpowering the faint reflection from the transponder. In the thesis, two adaptive RF front ends are introduced to eliminate the noise coupling from the transmitter. One of the most critical problems with UHF RFID has been the detuning of transponder antennas on different mounting platforms. The detuning may significantly diminish the read range of the transponder, especially on metal surfaces. In this thesis, two backscattering-based measurement techniques for the transponder antennas are presented. The detuning effect has been studied using these measurement techniques, and a platform tolerant antenna is introduced. RFID at millimetre waves enables miniaturisation of the reader antenna, and widening the data bandwidth over short distances. This could be used to access wirelessly mass memories with wide data bandwidth. A semi-passive or active transponder could communicate, e.g., with automotive radars. The millimetre wave identification (MMID) has been theoretically studied and experimentally verified at 60 GHz

    High-Isolation Low-Power Active Quasi-Circulator for 44GHz Transceiver with Power and Noise Optimization in 0.18 Micrometer BICMOS

    Get PDF
    Circulator is an important directional component in RF, microwave and millimeter wave communication front ends for certain communications, which requires transmitting and receiving signal simultaneously in the same band without switching of antenna from transmitter to receiver. As modern trend of wireless communication, conventional ferrite circulator is huge, bulky and heavy to be integrated with analog and digital baseband processing circuits. Active circulators provide a compact high isolation solution for low power application with smaller size and less cost with compatibility with modern IC. Previous works are majorly working at low frequency and paid little attention to power and noise requirement of active quasi-circulator working at the front end of a transceiver. A BiCMOS active quasi-circulator at 44GHz is designed in 0.18 μm process to provide high isolation low cost solution, which is comprised of in-phase divider and out-of-phase active combiner, with noise and power optimization. Moreover, techniques employed to improve isolation such as high Common mode rejection ratio(CMRR) balun design, common mode feedback, and novel method of power splitting and noise optimization, impedance matching scheme are discussed. High isolation of cascode structure is analyzed and major tradeoffs among characteristics are investigated, such as: gain and transmission-reception isolation; output impedance, matching and noise; linearity, power and efficiency. The circulator operates around 44 GHz with 3dB bandwidth of 4.53GHz, achieves maximum 2.897dBm input and 2.32dBm output power. Noise Figure (NF) is 10.62dB for reception path, only 0.03dB higher than NFmin. Linearity is reasonable for both in-phase divider and out-of-phase active combiner. OIP3 of in-phase divider is 8.15dBm, IIP3 is 4.48dBm, P1dB,in is -5.97dBm. OIP3 of out-of-phase active combiner is 5.18 dBm, IIP3 is 3.85dBm, P1dB, in is -2.79dBm. All the isolations better than -37 dB are achieved and forward gains better than 4 dB are achieved with power consumption 56.83mW. Large signal TX-RX isolation is 51.837dB. The circuit takes merely 1.415mm*1.014mm area. This active quasi-circulator offers a low cost substitute solution for circulator in low power applications

    Optimum single antenna full duplex using hybrid junctions

    Get PDF

    Analysis and Design of Silicon based Integrated Circuits for Radio Frequency Identification and Ranging Systems at 24GHz and 60GHz Frequency Bands

    Get PDF
    This scientific research work presents the analysis and design of radio frequency (RF) integrated circuits (ICs) designed for two cooperative RF identification (RFID) proof of concept systems. The first system concept is based on localizable and sensor-enabled superregenerative transponders (SRTs) interrogated using a 24GHz linear frequency modulated continuous wave (LFMCW) secondary radar. The second system concept focuses on low power components for a 60GHz continuous wave (CW) integrated single antenna frontend for interrogating close range passive backscatter transponders (PBTs). In the 24GHz localizable SRT based system, a LFMCW interrogating radar sends a RF chirp signal to interrogate SRTs based on custom superregenerative amplifier (SRA) ICs. The SRTs receive the chirp and transmit it back with phase coherent amplification. The distance to the SRTs are then estimated using the round trip time of flight method. Joint data transfer from the SRT to the interrogator is enabled by a novel SRA quench frequency shift keying (SQ-FSK) based low data rate simplex communication. The SRTs are also designed to be roll invariant using bandwidth enhanced microstrip patch antennas. Theoretical analysis is done to derive expressions as a function of system parameters including the minimum SRA gain required for attaining a defined range and equations for the maximum number of symbols that can be transmitted in data transfer mode. Analysis of the dependency of quench pulse characteristics during data transfer shows that the duty cycle has to be varied while keeping the on-time constant to reduce ranging errors. Also the worsening of ranging precision at longer distances is predicted based on the non-idealities resulting from LFMCWchirp quantization due to SRT characteristics and is corroborated by system level measurements. In order to prove the system concept and study the semiconductor technology dependent factors, variants of 24GHz SRA ICs are designed in a 130nm silicon germanium (SiGe) bipolar complementary metal oxide technology (BiCMOS) and a partially depleted silicon on insulator (SOI) technology. Among the SRA ICs designed, the SiGe-BiCMOS ICs feature a novel quench pulse shaping concept to simultaneously improve the output power and minimum detectable input power. A direct antenna drive SRA IC based on a novel stacked transistor cross-coupled oscillator topology employing this concept exhibit one of the best reported combinations of minimum detected input power level of −100 dBm and output power level of 5.6 dBm, post wirebonding. The SiGe stacked transistor with base feedback capacitance topology employed in this design is analyzed to derive parameters including the SRA loop gain for design optimization. Other theoretical contributions include the analysis of the novel integrated quench pulse shaping circuit and formulas derived for output voltage swing taking bondwire losses into account. Another SiGe design variant is the buffered antenna drive SRA IC having a measured minimum detected input power level better than −80 dBm, and an output power level greater than 3.2 dBm after wirebonding. The two inputs and outputs of this IC also enables the design of roll invariant SRTs. Laboratory based ranging experiments done to test the concepts and theoretical considerations show a maximum measured distance of 77m while transferring data at the rate of 0.5 symbols per second using SQ-FSK. For distances less than 10m, the characterized accuracy is better than 11 cm and the precision is better than 2.4 cm. The combination of the maximum range, precision and accuracy are one of the best reported among similar works in literature to the author’s knowledge. In the 60GHz close range CW interrogator based system, the RF frontend transmits a continuous wave signal through the transmit path of a quasi circulator (QC) interfaced to an antenna to interrogate a PBT. The backscatter is received using the same antenna interfaced to the QC. The received signal is then amplified and downconverted for further processing. To prove this concept, two optimized QC ICs and a downconversion mixer IC are designed in a 22nm fully depleted SOI technology. The first QC is the transmission lines based QC which consumes a power of 5.4mW, operates at a frequency range from 56GHz to 64GHz and occupies an area of 0.49mm2. The transmit path loss is 5.7 dB, receive path gain is 2 dB and the tunable transmit path to receive path isolation is between 20 dB and 32 dB. The second QC is based on lumped elements, and operates in a relatively narrow bandwidth from 59.6GHz to 61.5GHz, has a gain of 8.5 dB and provides a tunable isolation better than 20 dB between the transmit and receive paths. This QC design also occupies a small area of 0.34mm² while consuming 13.2mW power. The downconversion is realized using a novel folded switching stage down conversion mixer (FSSDM) topology optimized to achieve one of the best reported combination of maximum voltage conversion gain of 21.5 dB, a factor of 2.5 higher than reported state-of-the-art results, and low power consumption of 5.25mW. The design also employs a unique back-gate tunable intermediate frequency output stage using which a gain tuning range of 5.5 dB is attained. Theoretical analysis of the FSSDM topology is performed and equations for the RF input stage transconductance, bandwidth, voltage conversion gain and gain tuning are derived. A feasibility study for the components of the 60GHz integrated single antenna interrogator frontend is also performed using PBTs to prove the system design concept.:1 Introduction 1 1.1 Motivation and Related Work . . . . . . . . . . . . . . . . . . . . . 1 1.2 Scope and Functional Specifications . . . . . . . . . . . . . . . . . 4 1.3 Objectives and Structure . . . . . . . . . . . . . . . . . . . . . . . . 5 2 Features and Fundamentals of RFIDs and Superregenerative Amplifiers 9 2.1 RFID Transponder Technology . . . . . . . . . . . . . . . . . . . . 9 2.1.1 Chipless RFID Transponders . . . . . . . . . . . . . . . . . 10 2.1.2 Semiconductor based RFID Transponders . . . . . . . . . . 11 2.1.2.1 Passive Transponders . . . . . . . . . . . . . . . . 11 2.1.2.2 Active Transponders . . . . . . . . . . . . . . . . . 13 2.2 RFID Interrogator Architectures . . . . . . . . . . . . . . . . . . . 18 2.2.1 Interferometer based Interrogator . . . . . . . . . . . . . . . 19 2.2.2 Ultra-wideband Interrogator . . . . . . . . . . . . . . . . . . 20 2.2.3 Continuous Wave Interrogators . . . . . . . . . . . . . . . . 21 2.3 Coupling Dependent Range and Operating Frequencies . . . . . . . 25 2.4 RFID Ranging Techniques . . . . . . . . . . . . . . . . . . . . . . . 28 2.4.0.1 Received Signal Strength based Ranging . . . . . 28 2.4.0.2 Phase based Ranging . . . . . . . . . . . . . . . . 30 2.4.0.3 Time based Ranging . . . . . . . . . . . . . . . . . 30 2.5 Architecture Selection for Proof of Concept Systems . . . . . . . . 32 2.6 Superregenerative Amplifier (SRA) . . . . . . . . . . . . . . . . . . 35 2.6.1 Fundamentals . . . . . . . . . . . . . . . . . . . . . . . . . . 35 2.6.2 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . 42 2.6.3 Frequency Domain Characteristics . . . . . . . . . . . . . . 45 2.7 Semiconductor Technologies for RFIC Design . . . . . . . . . . . . 48 2.7.1 Silicon Germanium BiCMOS . . . . . . . . . . . . . . . . . 48 2.7.2 Silicon-on-Insulator . . . . . . . . . . . . . . . . . . . . . . . 48 3 24GHz Superregenerative Transponder based Identification and Rang- ing System 51 3.1 System Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 3.1.1 SRT Identification and Ranging . . . . . . . . . . . . . . . . 51 3.1.2 Power Link Analysis . . . . . . . . . . . . . . . . . . . . . . 55 3.1.3 Non-idealities . . . . . . . . . . . . . . . . . . . . . . . . . . 59 3.1.4 SRA Quench Frequency Shift Keying for data transfer . . . 61 3.1.5 Knowledge Gained . . . . . . . . . . . . . . . . . . . . . . . 63 3.2 RFIC Designs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 3.2.1 Low Power Direct Antenna Drive CMOS SRA IC . . . . . . 66 3.2.1.1 Circuit analysis and design . . . . . . . . . . . . . 66 3.2.1.2 Characterization . . . . . . . . . . . . . . . . . . . 69 3.2.2 Direct Antenna Drive SiGe SRA ICs . . . . . . . . . . . . . 71 3.2.2.1 Stacked Transistor Cross-coupled Quenchable Oscillator . . . . . . . . . . . . . . . . . . . . . . . . 72 3.2.2.1.1 Resonator . . . . . . . . . . . . . . . . . . 72 3.2.2.1.2 Output Network . . . . . . . . . . . . . . 75 3.2.2.1.3 Stacked Transistor Cross-coupled Pair and Loop Gain . . . . . . . . . . . . . . . . . 77 3.2.2.2 Quench Waveform Design . . . . . . . . . . . . . . 85 3.2.2.3 Characterization . . . . . . . . . . . . . . . . . . . 89 3.2.3 Antenna Diversity SiGe SRA IC with Integrated Quench Pulse Shaping . . . . . . . . . . . . . . . . . . . . . . . . . . 91 3.2.3.1 Circuit Analysis and Design . . . . . . . . . . . . 91 3.2.3.1.1 Crosscoupled Pair and Sampling Current 94 3.2.3.1.2 Common Base Input Stage . . . . . . . . 95 3.2.3.1.3 Cascode Output Stage . . . . . . . . . . . 96 3.2.3.1.4 Quench Pulse Shaping Circuit . . . . . . 96 3.2.3.1.5 Power Gain . . . . . . . . . . . . . . . . . 99 3.2.3.2 Characterization . . . . . . . . . . . . . . . . . . . 102 3.2.4 Knowledge Gained . . . . . . . . . . . . . . . . . . . . . . . 103 3.3 Proof of Principle System Implementation . . . . . . . . . . . . . . 106 3.3.1 Superregenerative Transponders . . . . . . . . . . . . . . . 106 3.3.1.1 Bandwidth Enhanced Microstrip Patch Antennas 108 3.3.2 FMCW Radar Interrogator . . . . . . . . . . . . . . . . . . 114 3.3.3 Chirp Z-transform Based Data Analysis . . . . . . . . . . . 116 4 60GHz Single Antenna RFID Interrogator based Identification System 121 4.1 System Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121 4.2 RFIC Designs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125 4.2.1 Quasi-circulator ICs . . . . . . . . . . . . . . . . . . . . . . 125 4.2.1.1 Transmission Lines based Quasi-Circulator IC . . 126 4.2.1.2 Lumped Elements WPD based Quasi-Circulator . 130 4.2.1.3 Characterization . . . . . . . . . . . . . . . . . . . 134 4.2.1.4 Knowledge Gained . . . . . . . . . . . . . . . . . . 135 4.2.2 Folded Switching Stage Downconversion Mixer IC . . . . . 138 4.2.2.1 FSSDM Circuit Design . . . . . . . . . . . . . . . 138 4.2.2.2 Cascode Transconductance Stage . . . . . . . . . . 138 4.2.2.3 Folded Switching Stage with LC DC Feed . . . . . 142 4.2.2.4 LO Balun . . . . . . . . . . . . . . . . . . . . . . . 145 4.2.2.5 Backgate Tunable IF Stage and Offset Correction 146 4.2.2.6 Voltage Conversion Gain . . . . . . . . . . . . . . 147 4.2.2.7 Characterization . . . . . . . . . . . . . . . . . . . 150 4.2.2.8 Knowledge Gained . . . . . . . . . . . . . . . . . . 151 4.3 Proof of Principle System Implementation . . . . . . . . . . . . . . 154 5 Experimental Tests 157 5.1 24GHz System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157 5.1.1 Ranging Experiments . . . . . . . . . . . . . . . . . . . . . 157 5.1.2 Roll Invariance Experiments . . . . . . . . . . . . . . . . . . 158 5.1.3 Joint Ranging and Data Transfer Experiments . . . . . . . 158 5.2 60GHz System Detection Experiments . . . . . . . . . . . . . . . . 165 6 Summary and Future Work 167 Appendices 171 A Derivation of Parameters for CB Amplifier with Base Feedback Capac- itance 173 B Definitions 177 C 24GHz Experiment Setups 179 D 60 GHz Experiment Setups 183 References 185 List of Original Publications 203 List of Abbreviations 207 List of Symbols 213 List of Figures 215 List of Tables 223 Curriculum Vitae 22

    Low Power Autonomous Microsystem for Oil Well Logging Applications

    Full text link
    Downhole environmental monitoring can provide significant benefits to the petroleum industry. The rapid development of semiconductor technology enables autonomous sensing microsystems to operate at extreme environments. By injecting these microsystems into the boreholes and retrieving them after deployment, the geophysical conditions in the area of interest can be obtained. Challenges include high temperature, high pressure, miniaturized system size and packaging. This dissertation describes three generations of the environmental logging microsystem (ELM) for downhole geophysical logging applications. The first generation of the microsystem, ELM1.0, is designed for temperature logging in downhole environments. Each system consists of a power management circuit, a microcontroller with an integrated temperature sensor, and optical indicators. The system electronics are integrated on a flexible printed circuit board and packaged in a steel shell. The ELM1.0 has a packaged size of 8.9×8.9×6.85 mm3. It was tested at up to 125°C, 50 MPa in high salinity condition. The second generation (ELM2.0 & ELM2.1) is upgraded from ELM1.0 by adding a micromachined capacitive pressure sensor for pressure sensing up to 50 MPa. The ELM2.0 & ELM2.1 systems are packaged in steel shells filled with transparent polymer for pressure transfer. The packaged systems have a dimension of 9.5×9.5×6.5 mm3. The third generation (ELM3.0) is upgraded from ELM2.0 with a power switch and a low-cost polyimide pressure sensor for coarse pressure measurement up to 50 MPa. Both ELM2.0 and ELM3.0 systems were successfully tested at up to 125°C, 50 MPa in corrosive environments using laboratory instruments, and in a brine well at a depth up to 1235 m. A progressive polynomial calibration method was used for interpretation of the pressure sensor data from these tests. In addition, a high power micromachined RF switch for radio transceiver applications was designed, fabricated and tested. The RF switch can potentially be used to establish antenna networks for RF communication in the ELM. The switch consists of a bridge structure for electrostatic actuation and capacitive contact. The switch was fabricated with a 7-mask process. The fabricated device showed limited RF performance because of challenges related to the control of residual stress in suspended elements.PHDElectrical EngineeringUniversity of Michigan, Horace H. Rackham School of Graduate Studieshttps://deepblue.lib.umich.edu/bitstream/2027.42/138647/1/sui_1.pd

    Desenho de antenas para sensores passivos em materiais não convencionais

    Get PDF
    Doutoramento em Engenharia EletrotécnicaMotivado pela larga expansão dos sistemas RFID e com o desenvolvimento do conceito de Internet das Coisas, a evolução no desenho e métodos de produção de antenas em suportes de materiais alternativos tem tido uma exploração intensiva nos últimos anos. Isto permitiu, não só o desenvolvimento de produtos no campo da interação homem-máquina, mas também tornar estes produtos mais pequenos e leves. A procura de novas técnicas e métodos para produzir eletrónica impressa e antenas em materiais alternativos e, portanto, uma porta aberta para o aparecimento de novas tecnologias. Isto aplica-se especialmente no mercado dos sensores, onde o peso, o tamanho, o consumo energético, e a adaptabilidade a diversos ambientes, têm grande relevância. Esta tese foca-se no desenvolvimento de antenas com suporte em materiais não convenvionais, como os já testados papel e têxteis, mas também na exploração de outros, desconhecidos do ponto de vista eléctrico, como a cortiça e polímeros biodegradáveis usados em impressão 3D. Estes materiais são portanto usados como substrato, ou material de suporte, para diversas antenas e, como tal, as propriedades electromagnéticas destes materiais têm de ser determinadas. Assim, e apresentado neste documento uma revisão de métodos de caracterização de materiais, bem como a proposta de um método baseado em linhas de trasmissão impressas, e a respectiva caracterização electromagnética de diversos materiais. Além disso, são propostos desenhos de antenas para diversos cenários e aplicações utilizando os materiais anteriormente mencionados. Com esta tese concluiu-se que a utilização de materiais alternativos e hoje uma realidade e os resultados obtidos são muito encorajodares para o desenvolvimento de um conjunto de sensores para aplicações RFID com uma grande capacidade de integração.The advancement of the design and fabrication of antennas using textiles or paper as substrates has rapidly grown motivated by the boom of RFID systems and the developing concept of the Internet of Things. These advancements have allowed, not only the development of products for manmachine interaction, but also to make these products smaller and lighter. The search for new techniques and methods to produce printed electronics and antennas in alternative materials is therefore an open door for new technologies to emerge. Especially in the sensors market, where weight, size, power consumption and the adaptability to the target application, are of great importance. This thesis focuses on the development of antenna design approaches with alternative materials, such as the already tested paper and textiles, but also others relatively unknown, such as cork and biodegradable polymers used in 3D printing. These materials are applied to act as substrates, or support structures for the antennas. Therefore, their electromagnetic properties need to be determined. Due to that, a review of electromagnetic characterization methods, as well as the proposal of a custom method based on printed transmission lines, is presented in this document. Besides, several antenna designs, for di erent application scenarios, using the previously mentioned materials, are proposed. With this thesis it was proved that it is possible to develop passive sensors in di erent alternative materials for RFID applications and others, which shows great promise in the use of these materials to achieve higher integration in sensing and identi cation applications

    Wireless wire - ultra-low-power and high-data-rate wireless communication systems

    Get PDF
    With the rapid development of communication technologies, wireless personal-area communication systems gain momentum and become increasingly important. When the market gets gradually saturated and the technology becomes much more mature, new demands on higher throughput push the wireless communication further into the high-frequency and high-data-rate direction. For example, in the IEEE 802.15.3c standard, a 60-GHz physical layer is specified, which occupies the unlicensed 57 to 64 GHz band and supports gigabit links for applications such as wireless downloading and data streaming. Along with the progress, however, both wireless protocols and physical systems and devices start to become very complex. Due to the limited cut-off frequency of the technology and high parasitic and noise levels at high frequency bands, the power consumption of these systems, especially of the RF front-ends, increases significantly. The reason behind this is that RF performance does not scale with technology at the same rate as digital baseband circuits. Based on the challenges encountered, the wireless-wire system is proposed for the millimeter wave high-data-rate communication. In this system, beamsteering directional communication front-ends are used, which confine the RF power within a narrow beam and increase the level of the equivalent isotropic radiation power by a factor equal to the number of antenna elements. Since extra gain is obtained from the antenna beamsteering, less front-end gain is required, which will reduce the power consumption accordingly. Besides, the narrow beam also reduces the interference level to other nodes. In order to minimize the system average power consumption, an ultra-low power asynchronous duty-cycled wake-up receiver is added to listen to the channel and control the communication modes. The main receiver is switched on by the wake-up receiver only when the communication is identified while in other cases it will always be in sleep mode with virtually no power consumed. Before transmitting the payload, the event-triggered transmitter will send a wake-up beacon to the wake-up receiver. As long as the wake-up beacon is longer than one cycle of the wake-up receiver, it can be captured and identified. Furthermore, by adopting a frequency-sweeping injection locking oscillator, the wake-up receiver is able to achieve good sensitivity, low latency and wide bandwidth simultaneously. In this way, high-data-rate communication can be achieved with ultra-low average power consumption. System power optimization is achieved by optimizing the antenna number, data rate, modulation scheme, transceiver architecture, and transceiver circuitries with regards to particular application scenarios. Cross-layer power optimization is performed as well. In order to verify the most critical elements of this new approach, a W-band injection-locked oscillator and the wake-up receiver have been designed and implemented in standard TSMC 65-nm CMOS technology. It can be seen from the measurement results that the wake-up receiver is able to achieve about -60 dBm sensitivity, 10 mW peak power consumption and 8.5 µs worst-case latency simultaneously. When applying a duty-cycling scheme, the average power of the wake-up receiver becomes lower than 10 µW if the event frequency is 1000 times/day, which matches battery-based or energy harvesting-based wireless applications. A 4-path phased-array main receiver is simulated working with 1 Gbps data rate and on-off-keying modulation. The average power consumption is 10 µW with 10 Gb communication data per day

    Conception et réalisation d'un nouveau transpondeur DSRC à faible consommation

    Get PDF
    To increase the efficiency and safety of the road traffic, new concepts and technologies have been developed in Europe since 1992 for RTTT applications (Road Traffic & Transport Telematics). These applications use the Dedicated Short Range Communications (DSRC) devices at 5.8 GHz (ISM band). In view of the reliability and success of this technology, the use of such equipment is thus extended to the EFC (Electronic Fee Collection) or e-toll and also in many other application areas such as fleet management, public transport and parking management. Due to the broad applications, these equipments are subject to various standards CEN/TC 278, CEN ENV (EN) 12253, ETSI, etc.... The DSRC system consists in a transceiver (reader) and transponders (tags). Industrial approaches are oriented to semi-passive transponder technology, which uses the same signal sent by the reader to retransmit, performing a frequency shift and encoding data to be transmitted. This design avoids the use of the local oscillators to generate the RF wave, as in active transponders, and save electrical energy of batteries. This allows the development of relatively low cost and small size transponders. Despite advances in integrated low-power circuits technology, this concept still requires a lithium battery to operate the transponder for a period of 4-6 years. However, with the expansion of these facilities, it appears that over the years the amount of lithium to destroy has become a crucial problem for the environment. Nowadays designing a completely autonomous DSRC transponder is not feasible, since the amount of energy required is still high (8 mA/3.6 V active mode). Nevertheless, reducing the transponder electrical power consumption, as a solution to at least double the battery life, could be a good start point to improve environment protection.In this thesis we propose a new DSRC transponder with an original statechart that considerably reduces the power consumption. After validation of the new low-power consumption mode, we studied the possibility to recharge the battery of the transponder by means of Wireless Energy Harvesting. The DSRC Toll Collection RF link budget was carried out in order to estimate the amount of energy available when a car with a transponder passes through a toll system. However, RF link budget at 5.8 GHz presents a low power density, since the car does not stay enough on the DSRC antenna's field to proceed to energy harvesting. Therefore we explored another ISM frequency, the 2.45 GHz. Thus the Wireless Energy Harvesting chapter aims to further the state of the art through the design and optimization of a novel RF harvesting board design. We demonstrated that an optimum RF-DC load is required in order to achieve high RF-DC conversion efficiency. Several rectifiers and rectennas were prototyped in order to validate the numerical studies. Finally, the results obtained in this thesis are in the forefront of the State-of-the-Art of Wireless Energy Harvesting for very low available power density.Afin d'augmenter l'efficacité et la sécurité du trafic routier, de nouveaux concepts et technologies ont été développés depuis 1992 en Europe pour les applications RTTT (Road Traffic & Transport Telematics). Ces applications utilisent les équipements DSRC qui supportent les transmissions à courte distance à 5.8GHz. Vues la fiabilité et le succès de cette technologie, l'utilisation de ces équipements est ensuite étendue aux ETC (Electronic Toll Collection) ou Télépéage et aussi dans une multitude d'autres domaines d'application comme la gestion des flottes, le transport public et la gestion des parkings. Le système DSRC se compose d'un émetteur/récepteur (lecteur) et des transpondeurs (badges). En toute logique, l'approche industrielle oriente les développements vers la technologie de transpondeur semi passif qui, pour réémettre un signal utilise le signal transmis par l'émetteur–récepteur, effectue une modulation de phase d'une sous porteuse fréquentielle encodant ainsi les données à transmettre. Cette conception évite l'utilisation des oscillateurs locaux, comme dans les transpondeurs actifs, pour générer l'onde Radio Fréquence (RF). Ceci permet de produire des transpondeurs relativement à faible coût et de petite taille. Cependant ce concept nécessite quand même une batterie au Lithium pour assurer le fonctionnement du transpondeur pour une durée de 4 à 6 ans et ce malgré les progrès des technologies de circuits intégrés à faible consommation. Au fur et à mesure de l'expansion de ces équipements, il s'avère qu'avec les années la quantité des batteries au lithium à détruire deviendrait un problème crucial pour l'environnement. Aujourd'hui, la conception d'un transpondeur DSRC complètement autonome n'est pas faisable, car la quantité d'énergie nécessaire s'avère encore élevée (mode actif 8 mA/3.6 V). Néanmoins, la réduction de la consommation électrique du transpondeur, permet au moins doubler la durée de vie de la batterie et pourrait être un bon point de départ pour améliorer la protection de l'environnement.Dans cette thèse, nous proposons un nouveau transpondeur DSRC avec un diagramme d'état original qui réduit considérablement la consommation énergétique. Après validation d'un nouvel état de fonctionnement en mode très faible consommation d'énergie, nous avons étudié la possibilité de recharger la batterie du transpondeur à travers de la récupération d'énergie sans fil. Le bilan de liaison énergétique DSRC a été réalisé afin d'estimer la quantité d'énergie disponible quand une voiture avec un transpondeur passe à sous un système de péage. Toutefois, le bilan énergétique à 5.8 GHz présente une faible densité d'énergie RF, puisque la voiture ne reste pas assez sur le lobe de l'antenne DSRC afin de procéder à la récupération d'énergie. Par conséquent, nous avons alors exploré une autre fréquence ISM, le 2.45 GHz dans laquelle la présence d'émetteurs est bien plus grande. Dans le chapitre de récupération d'énergie sans fil nous présentons la conception et l'optimisation d'un nouveau récupérateur d'énergie RF. Après avoir démontré qu'une charge RF-DC optimale est nécessaire afin d'atteindre une haute efficacité de conversion RF-DC. Plusieurs redresseurs et rectennas ont été conçus pour valider les études numériques. Parmi, les résultats présentés dans cette thèse les rendement de conversion obtenus sont à l'état de l'art de la récupération d'énergie sans fil pour une très faible densité de puissance disponible
    corecore