Energy Efficient RF Transmitter Design using Enhanced Breakdown Voltage SOI-CMOS Compatible MESFETs

abstract: The high cut-off frequency of deep sub-micron CMOS technologies has enabled the integration of radio frequency (RF) transceivers with digital circuits. However, the challenging point is the integration of RF power amplifiers, mainly due to the low breakdown voltage of CMOS transistors. Silicon-on-insulator (SOI) metal semiconductor field effect transistors (MESFETs) have been introduced to remedy the limited headroom concern in CMOS technologies. The MESFETs presented in this thesis have been fabricated on different SOI-CMOS processes without making any change to the standard fabrication steps and offer 2-30 times higher breakdown voltage than the MOSFETs on the same process. This thesis explains the design steps of high efficiency and wideband RF transmitters using the proposed SOI-CMOS compatible MESFETs. This task involves DC and RF characterization of MESFET devices, along with providing a compact Spice model for simulation purposes. This thesis presents the design of several SOI-MESFET RF power amplifiers operating at 433, 900 and 1800 MHz with ~40% bandwidth. Measurement results show a peak power added efficiency (PAE) of 55% and a peak output power of 22.5 dBm. The RF-PAs were designed to operate in Class-AB mode to minimize the linearity degradation. Class-AB power amplifiers lead to poor power added efficiency, especially when fed with signals with high peak to average power ratio (PAPR) such as wideband code division multiple access (W-CDMA). Polar transmitters have been introduced to improve the efficiency of RF-PAs at backed-off powers. A MESFET based envelope tracking (ET) polar transmitter was designed and measured. A low drop-out voltage regulator (LDO) was used as the supply modulator of this polar transmitter. MESFETs are depletion mode devices; therefore, they can be configured in a source follower configuration to have better stability and higher bandwidth that MOSFET based LDOs. Measurement results show 350 MHz bandwidth while driving a 10 pF capacitive load. A novel polar transmitter is introduced in this thesis to alleviate some of the limitations associated with polar transmitters. The proposed architecture uses the backgate terminal of a partially depleted transistor on SOI process, which relaxes the bandwidth and efficiency requirements of the envelope amplifier in a polar transmitter. The measurement results of the proposed transmitter demonstrate more than three times PAE improvement at 6-dB backed-off output power, compared to the traditional RF transmitters.Dissertation/ThesisPh.D. Electrical Engineering 201

A low quiescent current low dropout voltage regulator with self-compensation

This paper proposed a low quiescent current low-dropout voltage regulator (LDO) with self-compensation loop stability. This LDO is designed for Silicon-on-Chip (SoC) application without off-chip compensation capacitor. Worst case loop stability phenomenon happen when LDO output load current (Iload) is zero. The second pole frequency decreased tremendously towards unity-gain frequency (UGF) and compromise loop stability. To prevent this, additional current is needed to keep the output in low impedance in order to maintain second pole frequency. As Iload slowly increases, the unneeded additional current can be further reduced. This paper presents a circuit which performed self-reduction on this current by sensing the Iload. On top of that, a self-compensation circuit technique is proposed where loop stability is self-attained when Iload reduced below 100μA. In this technique, unity-gain frequency (UGF) will be decreaed and move away from second pole in order to attain loop stability. The decreased of UGF is done by reducing the total gain while maintaining the dominant pole frequency. This technique has also further reduced the total quiescent current and improved the LDO’s efficiency. The proposed LDO exhibits low quiescent current 9.4μA and 17.7μA, at Iload zero and full load 100mA respectively. The supply voltage for this LDO is 1.2V with 200mV drop-out voltage. The design is validated using 0.13μm CMOS process technology

A Silicon Carbide Linear Voltage Regulator for High Temperature Applications

Current market demands have pushed the capabilities of silicon to the edge. High temperature and high power applications require a semiconductor device to operate reliably in very harsh environments. This situation has awakened interests in other types of semiconductors, usually with a higher bandgap than silicon\u27s, as the next venue for the fabrication of integrated circuits (IC) and power devices. Silicon Carbide (SiC) has so far proven to be one of the best options in the power devices field. This dissertation presents the first attempt to fabricate a SiC linear voltage regulator. This circuit would provide a power management option for developing SiC processes due to its relatively simple implementation and yet, a performance acceptable to today\u27s systems applications. This document details the challenges faced and methods needed to design and fabricate the circuit as well as measured data corroborating design simulation results

CMOS MESFET Cascode Amplifiers for RFIC Applications

abstract: There is an ever-increasing demand for higher bandwidth and data rate ensuing from exploding number of radio frequency integrated systems and devices. As stated in the Shannon-Hartley theorem, the maximum achievable data rate of a communication channel is linearly proportional to the system bandwidth. This is the main driving force behind pushing wireless systems towards millimeter-wave frequency range, where larger bandwidth is available at a higher carrier frequency. Observing the Moor’s law, highly scaled complementary metal–oxide–semiconductor (CMOS) technologies provide fast transistors with a high unity power gain frequency which enables operating at millimeter-wave frequency range. CMOS is the compelling choice for digital and signal processing modules which concurrently offers high computation speed, low power consumption, and mass integration at a high manufacturing yield. One of the main shortcomings of the sub-micron CMOS technologies is the low breakdown voltage of the transistors that limits the dynamic range of the radio frequency (RF) power blocks, especially with the power amplifiers. Low voltage swing restricts the achievable output power which translates into low signal to noise ratio and degraded linearity. Extensive research has been done on proposing new design and IC fabrication techniques with the goal of generating higher output power in CMOS technology. The prominent drawbacks of these solutions are an increased die area, higher cost per design, and lower overall efficiency due to lossy passive components. In this dissertation, CMOS compatible metal–semiconductor field-effect transistor (MESFETs) are utilized to put forward a new solution to enhance the power amplifier’s breakdown voltage, gain and maximum output power. Requiring no change to the conventional CMOS process flow, this low cost approach allows direct incorporation of high voltage power MESFETs into silicon. High voltage MESFETs were employed in a cascode structure to push the amplifier’s cutoff frequency and unity power gain frequency to the 5G and K-band frequency range. This dissertation begins with CMOS compatible MESFET modeling and fabrication steps, and culminates in the discussion of amplifier design and optimization methodology, parasitic de-embedding steps, simulation and measurement results, and high resistivity RF substrate characterization.Dissertation/ThesisDoctoral Dissertation Electrical Engineering 201

Design of a low power internal voltage regulator for automotive applications

Tato diplomová práce se zabývá problematikou návrhu integrovaného regulátoru napětí. V práci jsou rozebrány topologie lineárních regulátorů napětí a jejich stabilita. Část práce se zabývá popisem a simulacemi bloků zvolené topologie regulátoru. Práce popisuje úskalí návrhu integrovaného obvodu v automobilovém průmyslu. V práci je vysvětleno zapojení navrhnutého regulátoru. Práce se zaměřuje také na stabilitu zapojení. Následně prezentuje provedené simulace. Probírá problematiku layoutu integrovaných obvodů a navrhnutého napěťového regulátoru.This master’s thesis deals with the design of integrated voltage regulator. Topologies of linear voltage regulators and their stability are discussed. Part of the thesis deals with description and simulation of blocks of selected regulator topology. The thesis describes the difficulties of integrated circuit design in the automotive industry. The electrical scheme of the designed regulator is explained. The work also focuses on the stability of designed regulator. Then presents simulations. It discusses the layout of integrated circuits and the designed voltage regulator.