Secondary Frequency and Voltage Control of Islanded Microgrids via Distributed Averaging

In this work we present new distributed controllers for secondary frequency and voltage control in islanded microgrids. Inspired by techniques from cooperative control, the proposed controllers use localized information and nearest-neighbor communication to collectively perform secondary control actions. The frequency controller rapidly regulates the microgrid frequency to its nominal value while maintaining active power sharing among the distributed generators. Tuning of the voltage controller provides a simple and intuitive trade-off between the conflicting goals of voltage regulation and reactive power sharing. Our designs require no knowledge of the microgrid topology, impedances or loads. The distributed architecture allows for flexibility and redundancy, and eliminates the need for a central microgrid controller. We provide a voltage stability analysis and present extensive experimental results validating our designs, verifying robust performance under communication failure and during plug-and-play operation.Comment: Accepted for publication in IEEE Transactions on Industrial Electronic

Suppression of Second-Order Harmonic Current for Droop-Controlled Distributed Energy Resource Converters in DC Microgrids

Droop-controlled distributed energy resource converters in dc microgrids usually show low output impedances. When coupled with ac systems, second-order harmonics typically appear on the dc-bus voltage, causing significant harmonic currents at the converters resource side. This paper shows how to reduce such undesired currents by means of notch filters and resonant regulators included in the converters control loops. The main characteristics of these techniques in terms of harmonic attenuation and stability are systematically investigated. In particular, it is shown that the voltage control-loop bandwidth is limited to be below twice the line frequency to avoid instability. Then, a modified notch filter and a modified resonant regulator are proposed, allowing to remove the constraint on the voltage loop bandwidth. The resulting methods (i.e., the notch filter, the resonant regulator, and their corresponding modified versions) are evaluated in terms of output impedance and stability. Experimental results from a dc microgrid prototype composed of three dc-dc converters and one dc-ac converter, all with a rated power of 5kW, are reported

Power-Based Droop Control in DC Microgrids Enabling Seamless Disconnection From Upstream Grids

This paper proposes a local power-based droop controller for distributed energy resource converters in dc microgrids that are connected to upstream grids by grid-interface converters. During normal operation, the grid-interface converter imposes the microgrid bus voltage, and the proposed controller allows power flow regulation at distributed energy resource converters\u2019 output. On the other hand, during abnormal operation of the grid-interface converter (e.g., due to faults in the upstream grid), the proposed controller allows bus voltage regulation by droop control. Notably, the controller can autonomously convert from power flow control to droop control, without any need of bus voltage variation detection schemes or communication with other microgrid components, which enables seamless transitions between these two modes of operation. Considering distributed energy resource converters employing the power-based droop control, the operation modes of a single converter and of the whole microgrid are defined and investigated herein. The controller design is also introduced. Furthermore, the power sharing performance of this control approach is analyzed and compared with that of classical droop control. The experimental results from a laboratory-scale dc microgrid prototype are reported to show the final performances of the proposed power-based droop control

Adaptive Virtual Impedance Droop Control Based on Consensus Control of Reactive Current

It is difficult to achieve accurate distribution of reactive power based on conventional droop control due to the line impedance mismatch in an islanded microgrid. An adaptive virtual impendence method based on consensus control of reactive current is proposed in this paper. A distributed control structure without the central controller has been established. In this structure, each distributed generation unit (DG) is an independent agent, one-way communication is used between the adjacent DGs, and the reactive power sharing is equivalent to a problem of reactive power current consensus. It has been proven that the system is asymptotically stable under the proposed control strategy. When the adjacent DG’s reactive power is not proportionally distributed, the current weight error term will generate a virtual impedance correction term through the proportional-integral controller based on the reactive current consensus control strategy, thus introducing adaptive virtual impedance to eliminate mismatches in output impedance between DGs. Reactive power auto-proportional distribution can be achieved without knowing the line impedance. At the same time, the power control loop is simplified and the virtual impedance compensation angle is employed to compensate the decreased reference voltage magnitude and varied phase angle due to the introduction of the virtual impedance, so the stability of the system can be improved. Finally, the correctness and effectiveness of the proposed strategy are verified by modeling analysis and microgrid simulations. Abstract It is difficult to achieve accurate distribution of reactive power based on conventional droop control due to the line impedance mismatch in an islanded microgrid. An adaptive virtual impendence method based on consensus control of reactive current is proposed in this paper. A distributed control structure without the central controller has been established. In this structure, each distributed generation unit (DG) is an independent agent, one-way communication is used between the adjacent DGs, and the reactive power sharing is equivalent to a problem of reactive power current consensus. It has been proven that the system is asymptotically stable under the proposed control strategy. When the adjacent DG’s reactive power is not proportionally distributed, the current weight error term will generate a virtual impedance correction term through the proportional-integral controller based on the reactive current consensus control strategy, thus introducing adaptive virtual impedance to eliminate mismatches in output impedance between DGs. Reactive power auto-proportional distribution can be achieved without knowing the line impedance. At the same time, the power control loop is simplified and the virtual impedance compensation angle is employed to compensate the decreased reference voltage magnitude and varied phase angle due to the introduction of the virtual impedance, so the stability of the system can be improved. Finally, the correctness and effectiveness of the proposed strategy are verified by modeling analysis and microgrid simulations

Three-phase primary control for unbalance sharing between distributed generation units in a microgrid

For islanded microgrids, droop-based control concepts have been developed both in single and three-phase variants. The three-phase controllers often assume a balanced network, hence, unbalance sharing and/or mitigation remains a challenging issue. Therefore, in this paper, unbalance is considered in a three-phase islanded microgrid where the distributed generation (DG) units are operated by the voltage-based droop (VBD) control. For this purpose, the VBD control, which has been developed for single-phase systems, is extended for three phase application and an additional control loop is added for unbalance mitigation and sharing. The method is based on an unbalance mitigation scheme by DG units in grid-connected systems, which is altered for usage in grid-forming DG units with droop control. The reaction of the DG units to unbalance is determined by the main parameter of the additional control loop, viz, the distortion damping resistance Rd. The effect of Rd on the unbalance mitigation is studied in this paper, i.e., dependent on Rd, the DG units can be resistive for unbalance (RU) or they can contribute in the weakest phase (CW). The paper shows that the RU method decreases the line losses in the system and achieves better power equalization between the DG unit's phases. However, it leads to a larger voltage unbalance near the loads. The CW method leads to a more uneven power between the DG unit's phases and larger line losses, but a better voltage quality near the load. However, it can negatively affect the stability of the system. In microgrids with multiple DG units, the distortion damping resistance is set such that the unbalanced load can be shared between multiple DG units in an actively controlled manner rather than being determined by the microgrid configuration solely. The unit with the lowest distortion resistance provides relatively more of the unbalanced currents

Analysis of an On-Line Stability Monitoring Approach for DC Microgrid Power Converters

An online approach to evaluate and monitor the stability margins of dc microgrid power converters is presented in this paper. The discussed online stability monitoring technique is based on the Middlebrook's loop-gain measurement technique, adapted to the digitally controlled power converters. In this approach, a perturbation is injected into a specific digital control loop of the converter and after measuring the loop gain, its crossover frequency and phase margin are continuously evaluated and monitored. The complete analytical derivation of the model, as well as detailed design aspects, are reported. In addition, the presence of multiple power converters connected to the same dc bus, all having the stability monitoring unit, is also investigated. An experimental microgrid prototype is implemented and considered to validate the theoretical analysis and simulation results, and to evaluate the effectiveness of the digital implementation of the technique for different control loops. The obtained results confirm the expected performance of the stability monitoring tool in steady-state and transient operating conditions. The proposed method can be extended to generic control loops in power converters operating in dc microgrids