A Generalized Approach to Analysing a Class of Passively Soft-Switched PWM DC-DC Converters

In this paper, a generalised approach to the analysis of a class of passively soft-switched PWM DC-DC converters is presented. The circuit cell that gives this class of converters its passively soft-switched characteristics is first introduced. The use of this circuit cell to transform the basic hard switched converters (buck, boost, bucklboost, Cuk's, Sepic and Zeta) into their varied passively soft-switched PWM topologies is illustratively presented. A generalised analysis representative of all the soft-switched converter types in the class is carried out

IMPROVEMENT STUDY ON SOFT-SWITCHED QUASI-RESONANT DC/DC BOOST CONVERTER

This report describes a novel soft-switched quasi-resonant DC/DC boost converter. Recently, remarkable efforts have been made in soft-switched quasi-resonant DC/DC converters to reduce losses and improve power efficiency. This project presents a new technique and it had improved the performance of the most recent study on soft-switched quasi-resonant DC/DC boost converter, which is presented in Ba-Thunya and Prasad's study [1]. The proposed converter employs an active snubber circuit with an auxiliary switch in series with a clamp capacitor to reduce powerlosses in Ba-Thunya and Prasad's original an active snubber circuit with an auxiliary switch and a clamp diode to reduce power losses in Ba-Thunya and Prasad's original converter. The energy from the snubber inductor after the auxiliary switch turn-off is returned to the input or delivered to the output via the active snubber circuit, thus the voltage stress onthe main switch is reduced and switching losses are minimized. Furthermore, the proposed converter reduces the reverse-recovery-related losses of the boost rectifier by controlling the di/dt rate of the rectifier current with the snubber inductor. This report describes the principle of operation of the new soft-switched quasi-resonant DC/DC boost converter. The feasibility study of the proposed converter is investigated using PSPICE program

A novel zero-current soft-switching converter for switched reluctance motor drives

A new zero-current-transition (ZCT) power converter for switched reluctance motor drive applications is presented. The proposed ZCT power converter possesses the definite advantages that both the main and auxiliary switches are operating with zero-current switching (ZCS), as well as minimum current and voltage stresses. It has a simple circuit topology, minimum component count and low cost. The ZCT technique can significantly reduce the switch-on or -off losses by forcing the current to zero prior to its turn-on or turn-off. The proposed power converter is especially advantageous for switched reluctance motor (SRM) drives demanding efficient regenerative braking, such as electric vehicle application.published_or_final_versio

Soft-Switching DC-DC Converters

Power electronics converters are implemented with switching devices that turn on and off while power is being converted from one form to another. They operate with high switching frequencies to reduce the size of the converters\u27 inductors, transformers and capacitors. Such high switching frequency operation, however, increases the amount of power that is lost due to switching losses and thus reduces power converter efficiency. Switching losses are caused by the overlap of switch voltage and switch current during a switching transition. If, however, either the voltage across or the current flowing through a switch is zero during a switching transition, then there is no overlap of switch voltage and switch current so in theory, there are no switching losses. Techniques that ensure that this happens are referred to as soft-switching techniques in the power electronics literature and there are two types: zero-voltage switching (ZVS) and zero-current switching (ZCS). For pulse-width modulated (PWM) Dc-Dc converters, both ZVS and ZCS are typically implemented with auxiliary circuits that help the main power switches operate with soft-switching. Although these auxiliary circuits do help improve the efficiency of the converters, they increase their cost. There is, therefore, motivation to try to make these auxiliary circuits as simple and as inexpensive as possible. Three new soft-switching Dc-Dc PWM converters are proposed in this thesis. For each converter, a very simple auxiliary circuit that consists of only a single active switching device and a few passive components is used to reduce the switching losses in the main power switches. The outstanding feature of each converter is the simplicity of its auxiliary circuit, which unlike most other previously proposed converters of similar type, avoids the use of multiple active auxiliary switches. In this thesis, the operation of each proposed converter is explained, analyzed, and the results of the analysis are used to develop a design procedure to select key component values. This design procedure is demonstrated with an example that was used in the implementation of an experimental prototype. The feasibility of each proposed converter is confirmed with experimental result obtained from a prototype converter

Development of Efficient Soft Switching Synchronous Buck Converter Topologies for Low Voltage High Current Applications

Switched mode power supplies (SMPS) have emerged as the popular candidate in all the power processing applications. The demand is soaring to design high power density converters. For reducing the size, weight, it is imperative to channelize the power at high switching frequency. High switching frequency converters insist upon soft switching techniques to curtail the switching losses. Several soft switching topologies have been evolved in the recent years. Nowadays, the soft switching converters are vastly applied modules and the demand is increasing for high power density and high efficiency modules by minimizing the conduction and switching losses. These modules are generally observed in many applications such as laptops, desktop processors for the enhancement of the battery life time. Apart from these applications, solar and spacecraft applications demand is increasing progressively for stressless and more efficient modules for maximizing the storage capacity which inturn enhances the power density that improves the battery life to supply in the uneven times. Modern trends in the consumer electronic market focus increases in the demand of lower voltage supplies. Conduction losses are significantly reduced by synchronous rectifiers i.e., MOSFET’s are essentially used in many of the low voltage power supplies. Active and passive auxiliary circuits are used in tandem with synchronous rectifier to diminish the crucial loss i.e., switching loss and also it minimizes the voltage and current stresses of the semiconductor devices. The rapid progress in the technology and emerging portable applications poses serious challenges to power supply design engineers for an efficient power converter design at high power density. The primary aim is to design and develop high efficiency, high power density topologies like: buck, synchronous buck and multiphase buck converters with the integration of soft switching techniques to minimize conduction and switching losses sustaining the voltage and current stresses within the tolerable range. In this work, two ZVT-ZCT PWM synchronous buck converters are introduced, one with active auxiliary circuit and the other one with passive auxiliary circuit. The operating principle and comprehensive steady state analysis of the ZVT-ZCT PWM synchronous buck converters are presented. The converters are designed to have high efficiency and low voltage that is suitable for high power density application. The semiconductor devices used in the topologies in addition to the main switch operate with soft switching conditions. The viii Abstract topologies proposed render a large overall efficiency in contrast to the contemporary topologies. In addition the circuit’s size is less, reliable and have high performance-cost ratio. The new generation microprocessor demands the features such as low voltage, high current, high power density and high efficiency etc., in the design of power supplies. The supply voltage for the future generation microprocessors must be low, in order to decrease the power consumption. The voltage levels are dripping to a level even less than 0.7V, and the power consumption increases as there is an increase in the current requirement for the processor. In order to meet the demands of the new generation microprocessor power supply, a soft switching multiphase PWM synchronous buck converter is proposed. The losses in the proposed topology due to increasing components are pared down by the proposed soft switching technique. The proposed converters in this research work are precisely described by the mathematical modelling and their operational modes. The practicality of the proposed converters for different applications is authenticated by their simulation and experimental results

Soft-Switching Techniques of Power Conversion System in Automotive Chargers

abstract: This thesis investigates different unidirectional topologies for the on-board charger in an electric vehicle and proposes soft-switching solutions in both the AC/DC and DC/DC stage of the converter with a power rating of 3.3 kW. With an overview on different charger topologies and their applicability with respect to the target specification a soft-switching technique to reduce the switching losses of a single phase boost-type PFC is proposed. This work is followed by a modification to the popular soft-switching topology, the dual active bridge (DAB) converter for application requiring unidirectional power flow. The topology named as the semi-dual active bridge (S-DAB) is obtained by replacing the fully active (four switches) bridge on the load side of a DAB by a semi-active (two switches and two diodes) bridge. The operating principles, waveforms in different intervals and expression for power transfer, which differ significantly from the basic DAB topology, are presented in detail. The zero-voltage switching (ZVS) characteristics and requirements are analyzed in detail and compared to those of DAB. A small-signal model of the new configuration is also derived. The analysis and performance of S-DAB are validated through extensive simulation and experimental results from a hardware prototype. Secondly, a low-loss auxiliary circuit for a power factor correction (PFC) circuit to achieve zero voltage transition is also proposed to improve the efficiency and operating frequency of the converter. The high dynamic energy generated in the switching node during turn-on is diverted by providing a parallel path through an auxiliary inductor and a transistor placed across the main inductor. The paper discusses the operating principles, design, and merits of the proposed scheme with hardware validation on a 3.3 kW/ 500 kHz PFC prototype. Modifications to the proposed zero voltage transition (ZVT) circuit is also investigated by implementing two topological variations. Firstly, an integrated magnetic structure is built combining the main inductor and auxiliary inductor in a single core reducing the total footprint of the circuit board. This improvement also reduces the size of the auxiliary capacitor required in the ZVT operation. The second modification redirects the ZVT energy from the input end to the DC link through additional half-bridge circuit and inductor. The half-bridge operating at constant 50% duty cycle simulates a switching leg of the following DC/DC stage of the converter. A hardware prototype of the above-mentioned PFC and DC/DC stage was developed and the operating principles were verified using the same.Dissertation/ThesisDoctoral Dissertation Electrical Engineering 201

A new zero-voltage-transition converter for switched reluctance motor drives

Firstly, a new zero-voltage-transition (ZVT) power converter for switched reluctance motor drives is presented. The proposed ZVT converter possesses the definite advantages that both main transistors and diodes can operate with zero-voltage switching (ZVS), unity device voltage and current stresses. Secondly, its zero-current counterpart is also presented, which offers both the main and auxiliary switches operating with zero-current switching (ZCS) and minimum current/voltage stress. They both have simple circuit topology, minimum component count and low cost. This family of power converters is especially advantageous for switched reluctance motor drives demanding efficient regenerative braking, such as in electric vehicle applications.published_or_final_versio

Isolated Single-stage Power Electronic Building Blocks Using Medium Voltage Series-stacked Wide-bandgap Switches

The demand for efficient power conversion systems that can process the energy at high power and voltage levels is increasing every day. These systems are to be used in microgrid applications. Wide-bandgap semiconductor devices (i.e. Silicon Carbide (SiC) and Gallium Nitride (GaN) devices) are very promising candidates due to their lower conduction and switching losses compared to the state-of-the-art Silicon (Si) devices. The main challenge for these devices is that their breakdown voltages are relatively lower compared to their Si counterpart. In addition, the high frequency operation of the wide-bandgap devices are impeded in many cases by the magnetic core losses of the magnetic coupling components (i.e. coupled inductors and/or high frequency transformers) utilized in the power converter circuit. Six new dc-dc converter topologies are propose. The converters have reduced voltage stresses on the switches. Three of them are unidirectional step-up converters with universal input voltage which make them excellent candidates for photovoltaic and fuel cell applications. The other three converters are bidirectional dc-dc converters with wide voltage conversion ratios. These converters are very good candidates for the applications that require bidirectional power flow capability. In addition, the wide voltage conversion ratios of these converters can be utilized for applications such as energy storage systems with wide voltage swings

A High Efficient High Input Power Factor Interleaved Boost Converter

In this paper an improved ZVT interleaved boost PFC topology is introduced. The proposed ZVT interleaved boost converter is composed of two cell boost conversion units and an active auxiliary circuit. The proposed converter has two important advantages over the similar soft switching converters. The first one is that parallel to the main switches of the converter the auxiliary switch also operates under soft switching condition. Providing soft switching conditions for interleaved boost converters with more than one cells using only one auxiliary switch is another advantage of this topology. The prototype for the proposed converter was developed with an input of 110V-220V ac power supply feeding a resistive output load of 600 watts. In addition, the proposed converter has the advantages of fewer structure complications, lower cost and ease of control.DOI:http://dx.doi.org/10.11591/ijece.v2i3.25

Efficient, High Power Density, Modular Wide Band-gap Based Converters for Medium Voltage Application

Recent advances in semiconductor technology have accelerated developments in medium-voltage direct-current (MVDC) power system transmission and distribution. A DC-DC converter is widely considered to be the most important technology for future DC networks. Wide band-gap (WBG) power devices (i.e. Silicon Carbide (SiC) and Gallium Nitride (GaN) devices) have paved the way for improving the efficiency and power density of power converters by means of higher switching frequencies with lower conduction and switching losses compared to their Silicon (Si) counterparts. However, due to rapid variation of the voltage and current, di/dt and dv/dt, to fully utilize the advantages of the Wide-bandgap semiconductors, more focus is needed to design the printed circuit boards (PCB) in terms of minimizing the parasitic components, which impacts efficiency. The aim of this dissertation is to study the technical challenges associated with the implementation of WBG devices and propose different power converter topologies for MVDC applications. Ship power system with MVDC distribution is attracting widespread interest due to higher reliability and reduced fuel consumption. Also, since the charging time is a barrier for adopting the electric vehicles, increasing the voltage level of the dc bus to achieve the fast charging is considered to be the most important solution to address this concern. Moreover, raising the voltage level reduces the size and cost of cables in the car. Employing MVDC system in the power grid offers secure, flexible and efficient power flow. It is shown that to reach optimal performance in terms of low package inductance and high slew rate of switches, designing a PCB with low common source inductance, power loop inductance, and gate-driver loop are essential. Compared with traditional power converters, the proposed circuits can reduce the voltage stress on switches and diodes, as well as the input current ripple. A lower voltage stress allows the designer to employ the switches and diodes with lower on-resistance RDS(ON) and forward voltage drop, respectively. Consequently, more efficient power conversion system can be achieved. Moreover, the proposed converters offer a high voltage gain that helps the power switches with smaller duty-cycle, which leads to lower current and voltage stress across them. To verify the proposed concept and prove the correctness of the theoretical analysis, the laboratory prototype of the converters using WBG devices were implemented. The proposed converters can provide energy conversion with an efficiency of 97% feeding the nominal load, which is 2% more than the efficiency of the-state-of-the-art converters. Besides the efficiency, shrinking the current ripple leads to 50% size reduction of the input filter inductors