Model Predictive Control Technique of Multilevel Inverter for PV Applications

Renewable energy sources, such as solar, wind, hydro, and biofuels, continue to gain popularity as alternatives to the conventional generation system. The main unit in the renewable energy system is the power conditioning system (PCS). It is highly desirable to obtain higher efficiency, lower component cost, and high reliability for the PCS to decrease the levelized cost of energy. This suggests a need for new inverter configurations and controls optimization, which can achieve the aforementioned needs. To achieve these goals, this dissertation presents a modified multilevel inverter topology for grid-tied photovoltaic (PV) system to achieve a lower cost and higher efficiency comparing with the existing system. In addition, this dissertation will also focus on model predictive control (MPC) which controls the modified multilevel topology to regulate the injected power to the grid. A major requirement for the PCS is harvesting the maximum power from the PV. By incorporating MPC, the performance of the maximum power point tracking (MPPT) algorithm to accurately extract the maximum power is improved for multilevel DC-DC converter. Finally, this control technique is developed for the quasi-z-source inverter (qZSI) to accurately control the DC link voltage, input current, and produce a high quality grid injected current waveform compared with the conventional techniques. This dissertation presents a modified symmetrical and asymmetrical multilevel DC-link inverter (MLDCLI) topology with less power switches and gate drivers. In addition, the MPC technique is used to drive the modified and grid connected MLDCLI. The performance of the proposed topology with finite control set model predictive control (FCS-MPC) is verified by simulation and experimentally. Moreover, this dissertation introduces predictive control to achieve maximum power point for grid-tied PV system to quicken the response by predicting the error before the switching signal is applied to the converter. Using the modified technique ensures the iii system operates at maximum power point which is more economical. Thus, the proposed MPPT technique can extract more energy compared to the conventional MPPT techniques from the same amount of installed solar panel. In further detail, this dissertation proposes the FCS-MPC technique for the qZSI in PV system. In order to further improve the performance of the system, FCS-MPC with one step horizon prediction has been implemented and compared with the classical PI controller. The presented work shows the proposed control techniques outperform the ones of the conventional linear controllers for the same application. Finally, a new method of the parallel processing is presented to reduce the time processing for the MPC

Three-Level Neutral-Point-Clamped Quasi-Z-Source Inverter with Maximum Power Point Tracking for Photovoltaic Systems

Part 12: Integration of Power Electronics Systems with ICT - IIInternational audienceThis article is focused on a photovoltaic system based on the three-level neutral-point-clamped quasi-z-source inverter. The maximum power point tracking (MPPT) algorithm based on dP/dV feedback was used in the photovoltaic system to adjust the duration of the shoot-through states of power switches and achieve a maximum power. Proper system operation in the case of irradiance step is demonstrated by simulation in Matlab/Simulink software

Low-voltage ride-through for a three-phase four-leg photovoltaic system using SRFPI control strategy

With the innovative progresses in power electronics in recent years, photovoltaic (PV) systems emerged as one of the promising sources for electricity generation at the distribution network. Nonetheless, connection of PV power plants to the utility grid under abnormal conditions has become a significant issue and novel grid codes should be recommend. The low-voltage ride-through (LVRT) capability is one of the challenges faced by the integration of PV power stations into electrical grid under abnormal conditions. This work firstly provides a discussion on recent control schemes for PV power plants to enhance the LVRT capabilities. Next, a control scheme for a three-phase four-leg grid-connected PV inverter under unbalanced grid fault conditions using synchronous reference frame proportional integral (SRFPI) controller is proposed. Simulation studies are performed to investigate the influence of the control strategy on the PV inverter

Modeling and control of a voltage-lift cell split-source inverter with MPPT for photovoltaic systems

In this study, a new single-stage inverter with improved boosting performance was proposed to enhance the recently developed split-source inverter (SSI) topology. The study introduced new SSI configurations with high voltage gain. The proposed design features a voltage-lift cell made of capacitors, inductors, and diodes, which increases the boosting capability. The decoupled control technique, where The DC input current is controlled by the AC modulation signals,allows for independent adjustment of both the DC input and AC output current. The research also employed a modified space vector modulation approach to manage the inverter switches and reduce current ripple. The combination of the proposed topology and the modified SVPWM scheme significantly improves the DC-boosting capabilities. the validity of the proposed solution was confirmed through simulation using three-phase SSI models in MATLAB/SIMULINK®. Finally, The validity of the simulation and experimental investigation of the analysis and performance of the topologies provided

Hybrid PV-Wind, Micro-Grid Development Using Quasi-Z-Source Inverter Modeling and Control—Experimental Investigation

This research work deals with the modeling and control of a hybrid photovoltaic (PV)-Wind micro-grid using Quasi Z-source inverter (QZsi). This inverter has major benefits as it provides better buck/boost characteristics, can regulate the phase angle output, has less harmonic contents, does not require the filter and has high power performance characteristics over the conventional inverter. A single ended primary inductance converter (SEPIC) module used as DC-DC switched power apparatus is employed for maximum power point tracking (MPPT) functions which provide high voltage gain throughout the process. Moreover, a modified power ratio variable step (MPRVS) based perturb & observe (P&O) method has been proposed, as part of the PV MPPT action, which forces the operating point close to the maximum power point (MPP). The proposed controller effectively correlates with the hybrid PV, Wind and battery system and provides integration of distributed generation (DG) with loads under varying operating conditions. The proposed standalone micro grid system is applicable specifically in rural places. The dSPACE real-time hardware platform has been employed to test the proposed micro grid system under varying wind speed, solar irradiation, load cutting and removing conditions etc. The experimental results based on a real-time digital platform, under dynamic conditions, justify the performance of a hybrid PV-Wind micro-grid with Quasi Z-Source inverter topology

Emerging Converter Topologies and Control for Grid Connected Photovoltaic Systems

Continuous cost reduction of photovoltaic (PV) systems and the rise of power auctions resulted in the establishment of PV power not only as a green energy source but also as a cost-effective solution to the electricity generation market. Various commercial solutions for grid-connected PV systems are available at any power level, ranging from multi-megawatt utility-scale solar farms to sub-kilowatt residential PV installations. Compared to utility-scale systems, the feasibility of small-scale residential PV installations is still limited by existing technologies that have not yet properly address issues like operation in weak grids, opaque and partial shading, etc. New market drivers such as warranty improvement to match the PV module lifespan, operation voltage range extension for application flexibility, and embedded energy storage for load shifting have again put small-scale PV systems in the spotlight. This Special Issue collects the latest developments in the field of power electronic converter topologies, control, design, and optimization for better energy yield, power conversion efficiency, reliability, and longer lifetime of the small-scale PV systems. This Special Issue will serve as a reference and update for academics, researchers, and practicing engineers to inspire new research and developments that pave the way for next-generation PV systems for residential and small commercial applications

Design of module level converters in photovoltaic power systems

The application of distributed maximum power point tracking (DMPPT) technology in solar photovoltaic (PV) systems is a hot topic in industry and academia. In the PV industry, grid integrated power systems are mainstream. The main objective for PV system design is to increase energy conversion efficiency and decrease the levelized cost of electricity of PV generators. This thesis firstly presents an extensive review of state-of-the-art PV technologies. With focus on grid integrated PV systems research, various aspects covered include PV materials, conventional full power processing DMPPT architectures, main MPPT techniques, and traditional partial power processing DMPPT architectures. The main restrictions to applying traditional DMPPT architectures in large power systems are discussed. A parallel connected partial power processing DMPPT architecture is proposed aiming to overcome existing restrictions. With flexible ‘plug-and-play’ functionality, the proposed architecture can be readily expanded to supply a downstream inverter stage or dc network. By adopting smaller module integrated converters, the proposed approach provides a possible efficiency improvement and cost reduction. The requirements for possible converter candidates and control strategies are analysed. One representative circuit scheme is presented as an example to verify the feasibility of the design. An electromagnetic transient model is built for different power scale PV systems to verify the DMPPT feasibility of the evaluated architecture in a large-scale PV power system. Voltage boosting ability is widely needed for converters in DMPPT applications. Impedance source converters (ISCs) are the main converter types with step-up ability. However, these converters have a general problem of low order distortion when applied in dc-ac applications. To solve this problem, a generic plug-in repetitive control strategy for a four-switch three-phase ISC type inverter configuration is developed. Simulation and experimental results confirm that this control strategy is suitable for many ISC converters.The application of distributed maximum power point tracking (DMPPT) technology in solar photovoltaic (PV) systems is a hot topic in industry and academia. In the PV industry, grid integrated power systems are mainstream. The main objective for PV system design is to increase energy conversion efficiency and decrease the levelized cost of electricity of PV generators. This thesis firstly presents an extensive review of state-of-the-art PV technologies. With focus on grid integrated PV systems research, various aspects covered include PV materials, conventional full power processing DMPPT architectures, main MPPT techniques, and traditional partial power processing DMPPT architectures. The main restrictions to applying traditional DMPPT architectures in large power systems are discussed. A parallel connected partial power processing DMPPT architecture is proposed aiming to overcome existing restrictions. With flexible ‘plug-and-play’ functionality, the proposed architecture can be readily expanded to supply a downstream inverter stage or dc network. By adopting smaller module integrated converters, the proposed approach provides a possible efficiency improvement and cost reduction. The requirements for possible converter candidates and control strategies are analysed. One representative circuit scheme is presented as an example to verify the feasibility of the design. An electromagnetic transient model is built for different power scale PV systems to verify the DMPPT feasibility of the evaluated architecture in a large-scale PV power system. Voltage boosting ability is widely needed for converters in DMPPT applications. Impedance source converters (ISCs) are the main converter types with step-up ability. However, these converters have a general problem of low order distortion when applied in dc-ac applications. To solve this problem, a generic plug-in repetitive control strategy for a four-switch three-phase ISC type inverter configuration is developed. Simulation and experimental results confirm that this control strategy is suitable for many ISC converters

Power quality improvements in grid-connected PV system using hybrid technology

In recent trends, photo-voltaic (PV) is mostly build upon competitive technological development of power quality (PQ) issues. In this article, a hybrid control strategy is implemented with multi-level inverter (MLI) to improve PQ features. As a result, the combination of these controllers with suitable level of MLI could improve the PQ features in a significant way.Peer ReviewedPostprint (published version