Nonlinear Characterization of Wideband Microwave Devices and Dispersive Effects in GaN HEMTs

Measurements play a key role in the development of microwave hardware as they allow engineers to test and verify the RF performance on a system, circuit, and component level. Since modern cellular standards employ complex modulation formats with wider signal bandwidths to cope with the growing demand of higher datarates, nonlinear characterization using wideband stimuli is becoming increasingly important. Furthermore, III-N semiconductor technologies such as gallium nitride (GaN) are to a larger extent utilized to enable higher performance in microwave circuits. However, GaN is highly frequency-dispersive due to trapping phenomena and thermal effects. This thesis deals with the development of nonlinear measurement instruments as well as characterization of dispersive effects in GaN high-electron-mobility transistors (HEMTs).A measurement setup for wideband, nonlinear characterization of microwave devices has been designed and verified. The setup allows for simultaneous acquisition of low-frequency and radio-frequency signals from DC up to 4~GHz through the use of wideband signal generators and measurement receivers. This enables measurement scenarios such as multi-band load-pull and large-signal characterization of IQ-mixers, which can give useful insight into how to optimize the performance in a RF transmitter.Electrothermal characterization of GaN devices has been carried out using conventional measurement methods such as pulsed I-V, and it is shown that trapping phenomena and thermal effects due to self-heating or mutual coupling are challenging to separate. Multiple methods must be utilized to fully characterize both the large-signal and small-signal impact on device performance. A new characterization method has been developed, for extraction of thermal transfer functions between mutually coupled devices on e.g. a semiconductor wafer. The method does not require any DC-bias on the measured devices, which can potentially reduce the influence of trapping during characterization of thermal properties in materials

Calibration enhancement of non-linear VNA system

Communication systems are generally found wherever data is to be transmitted from point-to-point or from a point to many points. It is impossible to imagine modern life without communication systems such as radio, telephone, TV, Satellite and etc. The transmission of information from one place to another requires an operation or other alteration to be sent through an electrical signal; the same principle applies for the receiving terminal. Modern life requires that efficient wireless communication systems for long range transmission be built, therefore, base-stations must use high power transistors almost exclusively. Furthermore, modern cellular communication systems also need to transmit across long distances, hence, to achieve this aim successfully, a radio frequency (RF) power amplifier is employed. That is considered to be a key element of any wireless communication system. Efficient communication systems must have minimum spectral re-growth, interference and employ linear. Signal amplification is one of the core circuit functions in modern microwave and RF systems. The Power Amplifier (PA) is a key element in the construction of all wireless communication systems. The PA uses the most current because it is the last stage in the transmission chain. In modern PA design, the RFPA designer must have accurate S-parameter data for the DUT, thereby allowing the creation of an accurate system model and to reduce the re-design and rework effort. The ultimate aim of the research work presented in this thesis is to achieve improvement in the accuracy of a waveform measurement system by increasing the accuracy of the small-signal calibration used. This involved removing the phase reference from the NVNA during calibration and operation, which in turn removes the bandwidth and frequency limitations that the phase reference imposes, as well as reducing the complexity of the overall system. Essential contributions to this research work concentrated in two areas; firstly, developments that allow for Enhanced Vector Calibration of Load-pull measurement systems, especially near the edge of the Smith Chart, and secondly, the operation and Anoor Aldoumani Abstract IV calibration of a VNA-based large-signal RF I-V waveform measurement system without using a harmonic phase reference standard. The first research area described in this thesis involved investigating the prospect of improving vector measurement accuracy, especially near the edge of the Smith Chart, by using load pull technology. Increased measurement error near the edge of the Smith chart was observed during calibration. To help correct this, the realisation of novel optimization that increases the accuracy of all the raw data which was collected during calibration process and therefore increases the accuracy of calibration at reflection coefficients close to unity. This research work focuses on taking advantage of the load-pull capability during calibration, this reduces the effect of measurement errors on the raw data when measuring the calibration standards before being applied in traditional LRL/TRL calibration algorithms. Leading to time proved measurement accuracy and eliminates the requirement to use complex optimisation algorithms post calibration. The second concept developed simplifies the NVNA architecture and removes the complexities and bandwidth limitations introduced when employing a harmonic phase reference generator. A key capability of the Rohde and Schwarz ZVA-67 VNA is that it incorporates internal signal and local oscillator sources and employs direct digital synthesis was exploited to advantage allows the Vector Network Analyzer to be operated as a NVNA without the need for a harmonic phase reference generator. This is due to such a Vector Network Analyzer based NVNA configuration provided a system with both coherent receivers and sources. This feature combined with a modified calibration procedure, means that during calibration only the internal signal sources and an external phase meter are required during measurement. All the internal signal sources and receiver port are available to measure, also now since no phase reference required, bandwidth and functionality issues and avoided

High-Performance On-Chip Microwave Photonic Signal Processing Using Linear and Nonlinear Optics

Manipulating and processing radio-frequency (RF) signals using integrated photonic devices has recently emerged as a paradigm-shifting technology for future microwave applications. This emerging technique is referred to as integrated microwave photonics (IMWP) which enables the high-frequency processing and unprecedentedly wideband tunability in compact photonic circuits, with significantly enhanced stability and robustness. However, to find widespread applications, the performance of IMWP devices must meet or exceed the achievable performance of conventional electronic counterparts. The work presented in this thesis investigates high-performance IMWP signal processing from two aspects: the optimized IMWP processing schemes and the photonic integration. Firstly, we explore novel schemes to improve the performance of chip-based microwave photonic subsystems, such as RF delay lines and RF filters which are basic building blocks of RF systems. A phase amplification technique is demonstrated to achieve a Si3N4 chip-based RF time delay with a delay tuning speed at gigahertz level. A new scheme to achieve an all-optimized RF photonic notch filter is demonstrated, producing a record-high RF link performance and complete functionalities. To unlock the potential of RF signal processing, we investigate a new filter concept of pairing linear and nonlinear optics for a high-performance RF photonic filter. To reduce the footprint of the novel IMWP filter, the photonic integration of both the ring resonators and Brillouin-active circuits on the same photonic chip is achieved. To eliminate the use of integrated optical circulators for on-chip SBS, on-chip backward inter-modal stimulated Brillouin scattering is predicted and experimentally demonstrated in a Si-Chalcogenide hybrid integrated photonic platform. The study and demonstrations presented in this thesis make the first viable step towards high-performance IMWP signal processing for real-world RF applications

Photonic Vector Processing Techniques for Radiofrequency Signals

[EN] The processing of radiofrequency signals using photonics means is a discipline that appeared almost at the same time as the laser and the optical fibre. Photonics offers the capability of managing broadband radiofrequency (RF) signals thanks to its low transmission attenuation, a variety of linear and non-linear phenomena and, recently, the potential to implement integrated photonic subsystems. These features open the door for the implementation of multiple functionalities including optical transportation, up and down frequency conversion, optical RF filtering, signal multiplexing, de-multiplexing, routing and switching, optical sampling, tone generation, delay control, beamforming and photonic generation of digital modulations, and even a combination of several of these functionalities. This thesis is focused on the application of vector processing in the optical domain to radiofrequency signals in two fields of application: optical beamforming, and photonic vector modulation and demodulation of digital quadrature amplitude modulations. The photonic vector control enables to adjust the amplitude and phase of the radiofrequency signals in the optical domain, which is the fundamental processing that is required in different applications such as beamforming networks for direct radiating array (DRA) antennas and multilevel quadrature modulation. The work described in this thesis include different techniques for implementing a photonic version of beamforming networks for direct radiating arrays (DRA) known as optical beamforming networks (OBFN), with the objectives of providing a precise control in terrestrial applications of broadband signals at very high frequencies above 40 GHz in communication antennas, optimizing the size and mass when compared with the electrical counterparts in space application, and presenting new photonic-based OBFN functionalities. Thus, two families of OBFNs are studied: fibre-based true time delay architectures and integrated networks. The first allow the control of broadband signals using dispersive optical fibres with wavelength division multiplexing techniques and advanced functionalities such as direction of arrival estimation in receiving architectures. In the second, passive OBFNs based on monolithically-integrated Optical Butler Matrices are studied, including an ultra-compact solution using optical heterodyne techniques in silicon-on-insulator (SOI) material, and an alternative implementing a homodyne counterpart in germanium doped silica material. In this thesis, the application of photonic vector processing to the generation of quadrature digital modulations has also been investigated. Multilevel modulations are based on encoding digital information in discrete states of phase and amplitude of an electrical signal to enhance spectral efficiency, as for instance, in quadrature modulation. The signal process required for generating and demodulating this kind of signals involves vector processing (phase and amplitude control) and frequency conversion. Unlike the common electronic or digital implementation, in this thesis, different photonic based signal processing techniques are studied to produce digital modulation (photonic vector modulation, PVM) and demodulation (PVdM). These techniques are of particular interest in the case of broadband signals where the data rate required to be managed is in the order of gigabit per second, for applications like wireless backhauling of metro optical networks (known as fibre-to-the-air). The techniques described use optical dispersion in optical fibres, wavelength division multiplexing and photonic up/down conversion. Additionally, an optical heterodyne solution implemented monolithically in a photonic integrated circuit (PIC) is also described.[ES] El procesamiento de señales de radiofrecuencia (RF) utilizando medios fotónicos es una disciplina que apareció casi al mismo tiempo que el láser y la fibra óptica. La fotónica ofrece la capacidad de manipular señales de radiofrecuencia de banda ancha, una baja atenuación, procesados basados en una amplia variedad de fenómenos lineales y no lineales y, recientemente, el potencial para implementar subsistemas fotónicos integrados. Estas características ofrecen un gran potencial para la implementación de múltiples funcionalidades incluyendo transporte óptico, conversión de frecuencia, filtrado óptico de RF, multiplexación y demultiplexación de señales, encaminamiento y conmutación, muestreo óptico, generación de tonos, líneas de retardo, conformación de haz en agrupaciones de antenas o generación fotónica de modulaciones digitales, e incluso una combinación de varias de estas funcionalidades. Esta tesis se centra en la aplicación del procesamiento vectorial en el dominio óptico de señales de radiofrecuencia en dos campos de aplicación: la conformación óptica de haces y la modulación y demodulación vectorial fotónica de señales digitales en cuadratura. El control fotónico vectorial permite manipular la amplitud y fase de las señales de radiofrecuencia en el dominio óptico, que es el procesamiento fundamental que se requiere en diferentes aplicaciones tales como las redes de conformación de haces para agrupaciones de antenas y en la modulación en cuadratura. El trabajo descrito en esta tesis incluye diferentes técnicas para implementar una versión fotónica de las redes de conformación de haces de en agrupaciones de antenas, conocidas como redes ópticas de conformación de haces (OBFN). Se estudian dos familias de redes: arquitecturas de retardo en fibra óptica y arquitecturas integradas. Las primeras permiten el control de señales de banda ancha utilizando fibras ópticas dispersivas con técnicas de multiplexado por división de longitud de onda y funcionalidades avanzadas tales como la estimación del ángulo de llegada de la señal en la antena receptora. En la segunda, se estudian redes de conformación pasivas basadas en Matrices de Butler ópticas integradas, incluyendo una solución ultra-compacta utilizando técnicas ópticas heterodinas en silicio sobre aislante (SOI), y una alternativa homodina en sílice dopado con germanio. En esta tesis, también se han investigado técnicas de procesado vectorial fotónico para la generación de modulaciones digitales en cuadratura. Las modulaciones multinivel codifican la información digital en estados discretos de fase y amplitud de una señal eléctrica para aumentar su eficiencia espectral, como por ejemplo la modulación en cuadratura. El procesado necesario para generar y demodular este tipo de señales implica el procesamiento vectorial (control de amplitud y fase) y la conversión de frecuencia. A diferencia de la implementación electrónica o digital convencional, en esta tesis se estudian diferentes técnicas de procesado fotónico tanto para la generación de modulaciones digitales (modulación vectorial fotónica, PVM) como para su demodulación (PVdM). Esto es de particular interés en el caso de señales de banda ancha, donde la velocidad de datos requerida es del orden de gigabits por segundo, para aplicaciones como backhaul inalámbrico de redes ópticas metropolitanas (conocida como fibra hasta el aire). Las técnicas descritas se basan en explotar la dispersión cromática de la fibra óptica, la multiplexación por división de longitud de onda y la conversión en frecuencia. Además, se presenta una solución heterodina implementada monolíticamente en un circuito integrado fotónico (PIC).[CA] El processament de senyals de radiofreqüència (RF) utilitzant mitjans fotònics és una disciplina que va aparèixer gairebé al mateix temps que el làser i la fibra òptica. La fotònica ofereix la capacitat de manipular senyals de radiofreqüència de banda ampla, una baixa atenuació, processats basats en una àmplia varietat de fenòmens lineals i no lineals i, recentment, el potencial per implementar subsistemes fotònics integrats. Aquestes característiques ofereixen un gran potencial per a la implementació de múltiples funcionalitats incloent transport òptic, conversió de freqüència, filtrat òptic de RF, multiplexació i demultiplexació de senyals, encaminament i commutació, mostreig òptic, generació de tons, línies de retard, conformació de feix en agrupacions d'antenes i la generació fotònica de modulacions digitals, i fins i tot una combinació de diverses d'aquestes funcionalitats. Aquesta tesi es centra en l'aplicació del processament vectorial en el domini òptic de senyals de radiofreqüència en dos camps d'aplicació: la conformació òptica de feixos i la modulació i demodulació vectorial fotònica de senyals digitals en quadratura. El control fotònic vectorial permet manipular l'amplitud i la fase dels senyals de radiofreqüència en el domini òptic, que és el processament fonamental que es requereix en diferents aplicacions com ara les xarxes de conformació de feixos per agrupacions d'antenes i en modulació multinivell. El treball descrit en aquesta tesi inclou diferents tècniques per implementar una versió fotònica de les xarxes de conformació de feixos en agrupacions d'antenes, conegudes com a xarxes òptiques de conformació de feixos (OBFN), amb els objectius de proporcionar un control precís en aplicacions terrestres de senyals de banda ampla a freqüències molt altes per sobre de 40 GHz en antenes de comunicacions, optimitzant la mida i el pes quan es compara amb els homòlegs elèctrics en aplicacions espacials, i la presentació de noves funcionalitats fotòniques per agrupacions d'antenes. Per tant, s'estudien dues famílies de OBFNs: arquitectures de retard en fibra òptica i arquitectures integrades. Les primeres permeten el control de senyals de banda ampla utilitzant fibres òptiques dispersives amb tècniques de multiplexació per divisió en longitud d'ona i funcionalitats avançades com ara l'estimació de l'angle d'arribada del senyal a l'antena receptora. A la segona, s'estudien xarxes de conformació passives basades en Matrius de Butler òptiques en fotònica integrada, incloent una solució ultra-compacta utilitzant tècniques òptiques heterodinas en silici sobre aïllant (SOI), i una alternativa homodina en sílice dopat amb germani. D'altra banda, també s'ha investigat en aquesta tesi tècniques de processament vectorial fotònic per a la generació de modulacions digitals en quadratura. Les modulacions multinivell codifiquen la informació digital en estats discrets de fase i amplitud d'un senyal elèctric per augmentar la seva eficiència espectral, com ara la modulació en quadratura. El processat necessari per generar i desmodular aquest tipus de senyals implica el processament vectorial (control d'amplitud i fase) i la conversió de freqüència. A diferència de la implementació electrònica o digital convencional, en aquesta tesi s'estudien diferents tècniques de processament fotònic tant per a la generació de modulacions digitals (modulació vectorial fotònica, PVM) com per la seva demodulació (PVdM). Això és de particular interès en el cas de senyals de banda ampla, on la velocitat de dades requerida és de l'ordre de gigabits per segon, per a aplicacions com backhaul sense fils de xarxes òptiques metropolitanes (coneguda com fibra fins l'aire). Les tècniques descrites es basen en explotar la dispersió cromàtica de la fibra òptica, la multiplexació per divisió en longitud d'ona i la conversió en freqüència. A més, es presePiqueras Ruipérez, MÁ. (2016). Photonic Vector Processing Techniques for Radiofrequency Signals [Tesis doctoral no publicada]. Universitat Politècnica de València. https://doi.org/10.4995/Thesis/10251/63264TESI

Developing a multi-tone load-pull system for the direct extraction of Cardiff behavioural model coefficients

The main objective of this thesis is to develop and utilize a high-speed measurement system based on PXIe modules for multi-tone measurements. This thesis addresses challenges that have been tackled during developing an accurate LabVIEW software to measure the multi-tone signal. Having solved these problems, the system's functionality was demonstrated by using it to extract some useful data such as stability and gain information for RF designers in, ‘real time’ during active load-pull measurements. In the final part of the thesis, the system was used to aid the development of the Cardiff behavioural model. One of the main challenges in the development of the Cardiff behavioural model is to correctly select the required mixing terms to have an accurate model. Initial work has been focused on determining the correct, phase polynomial coefficients of the Cardiff Model. The first technique presented in this thesis utilises two-tone measurements and the Fast Fourier Transform (FFT) to observe the mixing order from the resultant intermodulation (IMD) products, which are directly associated with the Cardiff Model coefficients. Employing the IFFT, the selected tones have been transferred to the time-domain travelling-wave. This allowed for b-wave analysis and load modulation coverage to be seen on the Smith Chart. The resultant load-modulation from the two-tone measurements has been used as a target for CW impedance measurements to verify whether the identification holds for the CW domain. The result shows there is an VII offset between the CW measurements and the two-tone measurements for larger annuli as th