캘리브레이션이 필요없는 위상고정 루프의 설계

학위논문 (박사)-- 서울대학교 대학원 : 전기·컴퓨터공학부, 2017. 2. 김재하.A PVT-insensitive-bandwidth PLL and a chirp frequency synthesizer PLL are proposed using a constant-relative-gain digitally-controlled oscillator (DCO), a constant-gain time-to-digital converter (TDC), and a simple digital loop filter (DLF) without an explicit calibration or additional circuit components. A digital LC-PLL that realizes a PVT-insensitive loop bandwidth (BW) by using the constant-relative-gain LC-DCO and constant-gain TDC is proposed. In other words, based on ratiometric circuit designs, the LC-DCO can make a fixed percent change to its frequency for a unit change in its digital input and the TDC can maintain a fixed range and resolution measured in reference unit intervals (UIs) across PVT variations. With such LC-DCO and TDC, the proposed PLL can realize a bandwidth which is a constant fraction of the reference frequency even with a simple proportional-integral digital loop filter without any explicit calibration loops. The prototype digital LC-PLL fabricated in a 28-nm CMOS demonstrates a frequency range of 8.38~9.34 GHz and 652-fs,rms integrated jitter from 10-kHz to 1-GHz at 8.84-GHz while dissipating 15.2-mW and occupying 0.24-mm^2. Also, the PLL across three different die samples and supply voltage ranging from 1.0 to 1.2V demonstrates a nearly constant BW at 822-kHz with the variation of ±4.25-% only. A chirp frequency synthesizer PLL (FS-PLL) that is capable of precise triangular frequency modulation using type-III digital LC-PLL architecture for X-band FMCW imaging radar is proposed. By employing a phase-modulating two-point modulation (TPM), constant-gain TDC, and a simple second-order DLF with polarity-alternating frequency ramp estimator, the PLL achieves a gain self-tracking TPM realizing a frequency chirp with fast chirp slope (=chirp BW/chirp period) without increasing frequency errors around the turn-around points, degrading the effective resolution achievable. A prototype chirp FS-PLL fabricated in a 65nm CMOS demonstrates that the PLL can generate a precise triangular chirp profile centered at 8.9-GHz with 940-MHz bandwidth and 28.8-us period with only 1.9-MHz,rms frequency error including the turn-around points and 14.8-mW power dissipation. The achieved 32.63-MHz/us chirp slope is higher than that of FMCW FS-PLLs previously reported by 2.6x.CHAPTER 1 INTRODUCTION 1 1.1 MOTIVATION 1 1.2 THESIS ORGANIZATION 5 CHAPTER 2 CONVENTIONAL PHASE-LOCKED LOOP 7 2.1 CHARGE-PUMP PLL 7 2.1.1 OPERATING PRINCIPLE 7 2.1.2 LOOP DYNAMICS 9 2.2 DIGITAL PLL 10 2.2.1 OPERATING PRINCIPLE 11 2.2.2 LOOP DYNAMICS 12 CHAPTER 3 VARIATIONS ON PHASE-LOCKED LOOP 14 3.1 OSCILLATOR GAIN VARIATION 14 3.1.1 RING VOLTAGE-CONTROLLED OSCILLATOR 15 3.1.2 LC VOLTAGE-CONTROLLED OSCILLATOR 17 3.1.3 LC DIGITALLY-CONTROLLED OSCILLATOR 19 3.2 PHASE DETECTOR GAIN VARIATION 20 3.2.1 LINEAR PHASE DETECTOR 20 3.2.2 LINEAR TIME-TO-DIGITAL CONVERTER 21 CHAPTER 4 PROPOSED DCO AND TDC FOR CALIBRATION-FREE PLL 23 4.1 DIGTALLY-CONTROLLED OSCILLATOR (DCO) 25 4.1.1 OVERVIEW 24 4.1.2 CONSTANT-RELATIVE-GAIN DCO 26 4.2 TIME-TO-DIGITAL CONVERTER (TDC) 28 4.2.1 OVERVIEW 28 4.2.2 CONSTANT-GAIN TDC 30 CHAPTER 5 PVT-INSENSITIVE-BANDWIDTH PLL 35 5.1 OVERVIEW 36 5.2 PRIOR WORKS 37 5.3 PROPOSED PVT-INSENSITIVE-BANDWIDTH PLL 39 5.4 CIRCUIT IMPLEMENTATION 41 5.4.1 CAPACITOR-TUNED LC-DCO 41 5.4.2 TRANSFORMER-TUNED LC-DCO 45 5.4.3 OVERSAMPLING-BASED CONSTANT-GAIN TDC 49 5.4.4 PHASE DIGITAL-TO-ANALOG CONVERTER 52 5.4.5 DIGITAL LOOP FILTER 54 5.4.6 FREQUENCY DIVIDER 55 5.4.7 BANG-BANG PHASE-FREQUENCY DETECTOR 56 5.5 CELL-BASED DESIGN FLOW 57 5.6 MEASUREMENT RESULTS 58 CHAPTER 6 CHIRP FREQUENCY SYNTHESIZER PLL 66 6.1 OVERVIEW 67 6.2 PRIOR WORKS 71 6.3 PROPOSED CHIRP FREQUENCY SYNTHESIZER PLL 75 6.4 CIRCUIT IMPLEMENTATION 83 6.4.1 SECOND-ORDER DIGITAL LOOP FILTER 83 6.4.2 PHASE MODULATOR 84 6.4.3 CONSTANT-GAIN TDC 85 6.4.4 VRACTOR-BASED LC-DCO 87 6.4.5 OVERALL CLOCK CHAIN 90 6.5 MEASUREMENT RESULTS 91 6.6 SIGNAL-TO-NOISE RATIO OF RADAR 98 CHAPTER 7 CONCLUSION 100 BIBLIOGRAPHY 102 초록 109Docto

Digital Centric Multi-Gigabit SerDes Design and Verification

Advances in semiconductor manufacturing still lead to ever decreasing feature sizes and constantly allow higher degrees of integration in application specific integrated circuits (ASICs). Therefore the bandwidth requirements on the external interfaces of such systems on chips (SoC) are steadily growing. Yet, as the number of pins on these ASICs is not increasing in the same pace - known as pin limitation - the bandwidth per pin has to be increased. SerDes (Serializer/Deserializer) technology, which allows to transfer data serially at very high data rates of 25Gbps and more is a key technology to overcome pin limitation and exploit the computing power that can be achieved in todays SoCs. As such SerDes blocks together with the digital logic interfacing them form complex mixed signal systems, verification of performance and functional correctness is very challenging. In this thesis a novel mixed-signal design methodology is proposed, which tightly couples model and implementation in order to ensure consistency throughout the design cycles and hereby accelerate the overall implementation flow. A tool flow that has been developed is presented, which integrates well into state of the art electronic design automation (EDA) environments and enables the usage of this methodology in practice. Further, the design space of todays high-speed serial links is analyzed and an architecture is proposed, which pushes complexity into the digital domain in order to achieve robustness, portability between manufacturing processes and scaling with advanced node technologies. The all digital phase locked loop (PLL) and clock data recovery (CDR), which have been developed are described in detail. The developed design flow was used for the implementation of the SerDes architecture in a 28nm silicon process and proved to be indispensable for future projects

Toward realizing power scalable and energy proportional high-speed wireline links

Growing computational demand and proliferation of cloud computing has placed high-speed serial links at the center stage. Due to saturating energy efficiency improvements over the last five years, increasing the data throughput comes at the cost of power consumption. Conventionally, serial link power can be reduced by optimizing individual building blocks such as output drivers, receiver, or clock generation and distribution. However, this approach yields very limited efficiency improvement. This dissertation takes an alternative approach toward reducing the serial link power. Instead of optimizing the power of individual building blocks, power of the entire serial link is reduced by exploiting serial link usage by the applications. It has been demonstrated that serial links in servers are underutilized. On average, they are used only 15% of the time, i.e. these links are idle for approximately 85% of the time. Conventional links consume power during idle periods to maintain synchronization between the transmitter and the receiver. However, by powering-off the link when idle and powering it back when needed, power consumption of the serial link can be scaled proportionally to its utilization. This approach of rapid power state transitioning is known as the rapid-on/off approach. For the rapid-on/off to be effective, ideally the power-on time, off-state power, and power state transition energy must all be close to zero. However, in practice, it is very difficult to achieve these ideal conditions. Work presented in this dissertation addresses these challenges. When this research work was started (2011-12), there were only a couple of research papers available in the area of rapid-on/off links. Systematic study or design of a rapid power state transitioning in serial links was not available in the literature. Since rapid-on/off with nanoseconds granularity is not a standard in any wireline communication, even the popular test equipment does not support testing any such feature, neither any formal measurement methodology was available. All these circumstances made the beginning difficult. However, these challenges provided a unique opportunity to explore new architectural techniques and identify trade-offs. The key contributions of this dissertation are as follows. The first and foremost contribution is understanding the underlying limitations of saturating energy efficiency improvements in serial links and why there is a compelling need to find alternative ways to reduce the serial link power. The second contribution is to identify potential power saving techniques and evaluate the challenges they pose and the opportunities they present. The third contribution is the design of a 5Gb/s transmitter with a rapid-on/off feature. The transmitter achieves rapid-on/off capability in voltage mode output driver by using a fast-digital regulator, and in the clock multiplier by accurate frequency pre-setting and periodic reference insertion. To ease timing requirements, an improved edge replacement logic circuit for the clock multiplier is proposed. Mathematical modeling of power-on time as a function of various circuit parameters is also discussed. The proposed transmitter demonstrates energy proportional operation over wide variations of link utilization, and is, therefore, suitable for energy efficient links. Fabricated in 90nm CMOS technology, the voltage mode driver, and the clock multiplier achieve power-on-time of only 2ns and 10ns, respectively. This dissertation highlights key trade-off in the clock multiplier architecture, to achieve fast power-on-lock capability at the cost of jitter performance. The fourth contribution is the design of a 7GHz rapid-on/off LC-PLL based clock multi- plier. The phase locked loop (PLL) based multiplier was developed to overcome the limita- tions of the MDLL based approach. Proposed temperature compensated LC-PLL achieves power-on-lock in 1ns. The fifth and biggest contribution of this dissertation is the design of a 7Gb/s embedded clock transceiver, which achieves rapid-on/off capability in LC-PLL, current-mode transmit- ter and receiver. It was the first reported design of a complete transceiver, with an embedded clock architecture, having rapid-on/off capability. Background phase calibration technique in PLL and CDR phase calibration logic in the receiver enable instantaneous lock on power-on. The proposed transceiver demonstrates power scalability with a wide range of link utiliza- tion and, therefore, helps in improving overall system efficiency. Fabricated in 65nm CMOS technology, the 7Gb/s transceiver achieves power-on-lock in less than 20ns. The transceiver achieves power scaling by 44x (63.7mW-to-1.43mW) and energy efficiency degradation by only 2.2x (9.1pJ/bit-to-20.5pJ/bit), when the effective data rate (link utilization) changes by 100x (7Gb/s-to-70Mb/s). The sixth and final contribution is the design of a temperature sensor to compensate the frequency drifts due to temperature variations, during long power-off periods, in the fast power-on-lock LC-PLL. The proposed self-referenced VCO-based temperature sensor is designed with all digital logic gates and achieves low supply sensitivity. This sensor is suitable for integration in processor and DRAM environments. The proposed sensor works on the principle of directly converting temperature information to frequency and finally to digital bits. A novel sensing technique is proposed in which temperature information is acquired by creating a threshold voltage difference between the transistors used in the oscillators. Reduced supply sensitivity is achieved by employing junction capacitance, and the overhead of voltage regulators and an external ideal reference frequency is avoided. The effect of VCO phase noise on the sensor resolution is mathematically evaluated. Fabricated in the 65nm CMOS process, the prototype can operate with a supply ranging from 0.85V to 1.1V, and it achieves a supply sensitivity of 0.034oC/mV and an inaccuracy of ±0.9oC and ±2.3oC from 0-100oC after 2-point calibration, with and without static nonlinearity correction, respectively. It achieves a resolution of 0.3oC, resolution FoM of 0.3(nJ/conv)res2 , and measurement (conversion) time of 6.5μs

A Low Jitter Wideband Fractional-N Subsampling Phase Locked Loop (SSPLL)

Frequency synthesizers have become a crucial building block in the evolution of modern communication systems and consumer electronics. The spectral purity performance of frequency synthesizers limits the achievable data-rate and presents a noise-power tradeoff. For communication standards such as LTE where the channel spacing is a few kHz, the synthesizers must provide high frequencies with sufficiently wide frequency tuning range and fine frequency resolutions. Such stringent performance must be met with a limited power and small chip area. In this thesis a wideband fractional-N frequency synthesizer based on a subsampling phase locked loop (SSPLL) is presented. The proposed synthesizer which has a frequency resolution less than 100Hz employs a digital fractional controller (DFC) and a 10-bit digital-to-time converter (DTC) to delay the rising edges of the reference clock to achieve fractional phase lock. For fast convergence of the delay calibration, a novel two-step delay correlation loop (DCL) is employed. Furthermore, to provide optimum settling and jitter performance, the loop transfer characteristics during frequency acquisition and phase-lock are decoupled using a dual input loop filter (DILF). The fractional-N sub-sampling PLL (FNSSPLL) is implemented in a TSMC 40nm CMOS technology and occupies a total active area of 0.41mm^2. The PLL operates over frequency range of 2.8 GHz to 4.3 GHz (42% tuning range) while consuming 9.18mW from a 1.1V supply. The integrated jitter performance is better than 390 fs across all fractional frequency channel. The worst case fractional spur of -48.3 dBc occurs at a 650 kHz offset for a 3.75GHz fractional channel. The in-band phase noise measured at a 200 kHz offset is -112.5 dBc/Hz

A stochastic time-to-digital converter for digital phase-locked loops

Digital phase-locked loops (PLLs) have been receiving increasing attention recently due to their ease of integration, scalability and performance comparable to their analog counterparts. In digital PLLs, increased resolution in time-to-digital conversion is desirable for improved noise performance. This work describes the design and simulation of a stochastic time-to-digital converter (STDC) for a digital PLL to attain high resolution. The converter is intended to comprise the fine loop of the phase-frequency detector, whose coarse loop would be comprised of a time-to-digital converter designed using the conventional delay-chain approach. The STDC is designed, simulated and sent for fabrication in a 0.35μm SOI CMOS process. System level simulations in MATLAB are verified by device level simulations in Spectre on circuits extracted from layout. The results support the viability of using the proposed circuit for high resolution time-to-digital conversion.Keywords: time-to-digital converter, dpl

Timing Signals and Radio Frequency Distribution Using Ethernet Networks for High Energy Physics Applications

Timing networks are used around the world in various applications from telecommunications systems to industrial processes, and from radio astronomy to high energy physics. Most timing networks are implemented using proprietary technologies at high operation and maintenance costs. This thesis presents a novel timing network capable of distributed timing with subnanosecond accuracy. The network, developed at CERN and codenamed “White- Rabbit”, uses a non-dedicated Ethernet link to distribute timing and data packets without infringing the sub-nanosecond timing accuracy required for high energy physics applications. The first part of this thesis proposes a new digital circuit capable of measuring time differences between two digital clock signals with sub-picosecond time resolution. The proposed digital circuit measures and compensates for the phase variations between the transmitted and received network clocks required to achieve the sub-nanosecond timing accuracy. Circuit design, implementation and performance verification are reported. The second part of this thesis investigates and proposes a new method to distribute radio frequency (RF) signals over Ethernet networks. The main goal of existing distributed RF schemes, such as Radio-Over-Fibre or Digitised Radio-Over-Fibre, is to increase the bandwidth capacity taking advantage of the higher performance of digital optical links. These schemes tend to employ dedicated and costly technologies, deemed unnecessary for applications with lower bandwidth requirements. This work proposes the distribution of RF signals over the “White-Rabbit” network, to convey phase and frequency information from a reference base node to a large numbers of remote nodes, thus achieving high performance and cost reduction of the timing network. Hence, this thesis reports the design and implementation of a new distributed RF system architecture; analysed and tested using a purpose-built simulation environment, with results used to optimise a new bespoke FPGA implementation. The performance is evaluated through phase-noise spectra, the Allan-Variance, and signalto- noise ratio measurements of the distributed signals

Design of Digital FMCW Chirp Synthesizer PLLs Using Continuous-Time Delta-Sigma Time-to-Digital Converters

Radar applications for driver assistance systems and autonomous vehicles have spurred the development of frequency-modulated continuous-wave (FMCW) radar. Continuous signal transmission and high operation frequencies in the K- and W-bands enable radar systems with low power consumption and small form factors. The radar performance depends on high-quality signal sources for chirp generation to ensure accurate and reliable target detection, requiring chirp synthesizers that offer fast frequency settling and low phase noise. Fractional-N phase locked loops (PLLs) are an effective tool for synthesis of FMCW waveform profiles, and advances in CMOS technology have enabled high-performance single-chip CMOS synthesizers for FMCW radar. Design approaches for FMCW chirp synthesizer PLLs need to address the conflicting requirements of fast settling and low close-in phase noise. While integrated PLLs can be implemented as analog or digital PLLs, analog PLLs still dominate for high frequencies. Digital PLLs offer greater programmability and area efficiency than their analog counterparts, but rely on high-resolution time-to-digital converters (TDCs) for low close-in phase noise. Performance limitations of conventional TDCs remain a roadblock for achieving low phase noise with high-frequency digital PLLs. This shortcoming of digital PLLs becomes even more pronounced with wide loop bandwidths as required for FMCW radar. To address this problem, this work presents digital FMCW chirp synthesizer PLLs using continuous-time delta-sigma TDCs. After a discussion of the requirements for PLL-based FMCW chirp synthesizers, this dissertation focuses on digital fractional-N PLL designs based on noise-shaping TDCs that leverage state-of-the-art delta-sigma modulator techniques to achieve low close-in phase noise in wide-bandwidth digital PLLs. First, an analysis of the PLL bandwidth and chirp linearity studies the design requirements for chirp synthesizer PLLs. Based on a model of a complete radar system, the analysis examines the impact of the PLL bandwidth on the radar performance. The modeling approach allows for a straightforward study of the radar accuracy and reliability as functions of the chirp parameters and the PLL configuration. Next, an 18-to-22GHz chirp synthesizer PLL that produces a 25-segment chirp for a 240GHz FMCW radar application is described. This synthesizer design adapts an existing third-order noise-shaping TDC design. A 65nm CMOS prototype achieves a measured close-in phase noise of -88dBc/Hz at 100kHz offset for wide PLL bandwidths and consumes 39.6mW. The prototype drives a radar testbed to demonstrate the effectiveness of the synthesizer design in a complete radar system. Finally, a second-order noise-shaping TDC based on a fourth-order bandpass delta-sigma modulator is introduced. This bandpass delta-sigma TDC leverages the high resolution of a bandpass delta-sigma modulator by sampling a sinusoidal PLL reference and applies digital down-conversion to achieve low TDC noise in the frequency band of interest. Based on the bandpass delta-sigma TDC, a 38GHz digital FMCW chirp synthesizer PLL is designed. The feedback divider applies phase interpolation with a phase rotation scheme to ensure the effectiveness of the low TDC noise. A prototype PLL, fabricated in 40nm CMOS, achieves a measured close-in phase noise of -85dBc/Hz at 100kHz offset for wide loop bandwidths >1MHz and consumes 68mW. It effectively generates fast (500MHz/55us) and precise (824kHz rms frequency error) triangular chirps for FMCW radar. The bandpass delta-sigma TDC achieves a measured integrated rms noise of 325fs in a 1MHz bandwidth.PHDElectrical EngineeringUniversity of Michigan, Horace H. Rackham School of Graduate Studieshttps://deepblue.lib.umich.edu/bitstream/2027.42/147732/1/dweyer_1.pdfDescription of dweyer_1.pdf : Restricted to UM users only