1,278 research outputs found
Digitally-Enhanced Software-Defined Radio Receiver Robust to Out-of-Band Interference
A software-defined radio (SDR) receiver with improved robustness to out-of-band interference (OBI) is presented. Two main challenges are identified for an OBI-robust SDR receiver: out-of-band nonlinearity and harmonic mixing. Voltage gain at RF is avoided, and instead realized at baseband in combination with low-pass filtering to mitigate blockers and improve out-of-band IIP3. Two alternative “iterative” harmonic-rejection (HR) techniques are presented to achieve high HR robust to mismatch: a) an analog two-stage polyphase HR concept, which enhances the HR to more than 60 dB; b) a digital adaptive interference cancelling (AIC) technique, which can suppress one dominating harmonic by at least 80 dB. An accurate multiphase clock generator is presented for a mismatch-robust HR. A proof-of-concept receiver is implemented in 65 nm CMOS. Measurements show 34 dB gain, 4 dB NF, and 3.5 dBm in-band IIP3 while the out-of-band IIP3 is + 16 dBm without fine tuning. The measured RF bandwidth is up to 6 GHz and the 8-phase LO works up to 0.9 GHz (master clock up to 7.2 GHz). At 0.8 GHz LO, the analog two-stage polyphase HR achieves a second to sixth order HR > dB over 40 chips, while the digital AIC technique achieves HR > 80 dB for the dominating harmonic. The total power consumption is 50 mA from a 1.2 V supply
Equalization of Third-Order Intermodulation Products in Wideband Direct Conversion Receivers
This paper reports a SAW-less direct-conversion receiver which utilizes a mixed-signal feedforward path to regenerate and adaptively cancel IM3 products, thus accomplishing system-level linearization. The receiver system performance is dominated by a custom integrated RF front end implemented in 130-nm CMOS and achieves an uncorrected out-of-band IIP3 of -7.1 dBm under the worst-case UMTS FDD Region 1 blocking specifications. Under IM3 equalization, the receiver achieves an effective IIP3 of +5.3 dBm and meets the UMTS BER sensitivity requirement with 3.7 dB of margin
A 0.18μm CMOS 300MHz Current-Mode LF Seventh-order Linear Phase Filter for Hard Disk Read Channels
“This material is presented to ensure timely dissemination of scholarly and technical work. Copyright and all rights therein are retained by authors or by other copyright holders. All persons copying this information are expected to adhere to the terms and constraints invoked by each author's copyright. In most cases, these works may not be reposted without the explicit permission of the copyright holder." “Copyright IEEE. Personal use of this material is permitted. However, permission to reprint/republish this material for advertising or promotional purposes or for creating new collective works for resale or redistribution to servers or lists, or to reuse any copyrighted component of this work in other works must be obtained from the IEEE.”A 300MHz CMOS seventh-order linear phase gm-C filter based on a current-mode multiple loop feedback (MLF) leap-frog (LF) structure is realized. The filter is implemented using a fully-differential linear operational transconductance amplifier (OTA) based on a source degeneration topology. PSpice simulations using a standard TSMC 0.18μm CMOS process with 2.5V power supply have shown that the cut-off frequency of the filter can be tuned from 260MHz to 320MHz and dynamic range is about 66dB. Group delay ripple is approximately 4.5% over the whole tuning range and maximum power consumption is 210mW
Multi-tone Active Noise Equalizer with Spatially Distributed User-selected Profiles
[EN] In this work we propose a multi-channel active noise equalizer (ANE) that can deal with multi-frequency noise signals and assigns simultaneously different equalization gains to each frequency component at each monitoring sensor. For this purpose, we state a pseudo-error noise signal for each sensor of the ANE, which has to be cancelled out in order to get the desired equalization profiles. Firstly the optimal analytic solution for the ANE filters in the case of single-frequency noise is provided, and an adaptive algorithm based on the Least Mean Squared (LMS) is proposed for the same case. We also show that this adaptive strategy reaches the theoretical solution in steady state. Secondly, we state an equivalent approach for the case of multi-frequency noise based on two alternatives: a common pseudo-error signal at each sensor for all frequencies, and a different pseudo-error signal at each sensor for each frequency. The analytic and adaptive solutions for the ANE control filters have been developed for both pseudo-error alternatives. Finally, the ability of the proposed ANE to achieve simultaneously different user-selected noise profiles in different locations has been validated by their transfer functions and simulations.This work was supported by EU jointly with Spanish Government and Generalitat Valenciana under Grants RTI2018-098085-BC41, PID2021-125736OB-I00 (MCIU/AEI/FEDER), RE D2018-102668-T, and PROMETEO/2019/109.Ferrer Contreras, M.; Diego Antón, MD.; Hassani, A.; Moonen, M.; Piñero, G.; Gonzalez, A. (2022). Multi-tone Active Noise Equalizer with Spatially Distributed User-selected Profiles. IEEE/ACM Transactions on Audio Speech and Language Processing. 30:3199-3213. https://doi.org/10.1109/TASLP.2022.3212833319932133
Review of active noise control techniques with emphasis on sound quality enhancement
The traditional active noise control design aims to attenuate the energy of residual noise, which is indiscriminative in the frequency domain. However, it is necessary to retain residual noise with a specified spectrum to satisfy the requirements of human perception in some applications. In this paper, the evolution of active noise control and sound quality are briefly discussed. This paper emphasizes on the advancement of active noise control method in the past decades in terms of enhancing the sound quality
Design of adaptive analog filters for magnetic front-end read channels
Esta tese estuda o projecto e o comportamento de filtros em tempo contínuo de
muito-alta-frequência. A motivação deste trabalho foi a investigação de soluções de filtragem
para canais de leitura em sistemas de gravação e reprodução de dados em suporte
magnético, com custos e consumo (tamanho total inferior a 1 mm2 e consumo inferior a
1mW/polo), inferiores aos circuitos existentes. Nesse sentido, tal como foi feito neste
trabalho, o rápido desenvolvimento das tecnologias de microelectrónica suscitou esforços
muito significativos a nível mundial com o objectivo de se investigarem novas técnicas
de realização de filtros em circuito integrado monolítico, especialmente em tecnologia
CMOS (Complementary Metal Oxide Semiconductor). Apresenta-se um estudo comparativo
a diversos níveis hierárquicos do projecto, que conduziu à realização e caracterização
de soluções com as características desejadas.
Num primeiro nível, este estudo aborda a questão conceptual da gravação e transmissão
de sinal bem como a escolha de bons modelos matemáticos para o tratamento da
informação e a minimização de erro inerente às aproximações na conformidade aos princípios
físicos dos dispositivos caracterizados.
O trabalho principal da tese é focado nos níveis hierárquicos da arquitectura do
canal de leitura e da realização em circuito integrado do seu bloco principal – o bloco de
filtragem. Ao nível da arquitectura do canal de leitura, apresenta-se um estudo alargado
sobre as metodologias existentes de adaptação de sinal e recuperação de dados em suporte
magnético. Este desígnio aparece no âmbito da proposta de uma solução de baixo custo,
baixo consumo, baixa tensão de alimentação e baixa complexidade, alicerçada em tecnologia
digital CMOS, para a realização de um sistema DFE (Decision Feedback Equalization)
com base na igualização de sinal utilizando filtros integrados analógicos em tempo
contínuo.
Ao nível do projecto de realização do bloco de filtragem e das técnicas de implementação
de filtros e dos seus blocos constituintes em circuito integrado, concluiu-se que
a técnica baseada em circuitos de transcondutância e condensadores, também conhecida como filtros gm-C (ou transcondutância-C), é a mais adequada para a realização de filtros
adaptativos em muito-alta-frequência. Definiram-se neste nível hierárquico mais baixo,
dois subníveis de aprofundamento do estudo no âmbito desta tese, nomeadamente: a pesquisa
e análise de estruturas ideais no projecto de filtros recorrendo a representações no
espaço de estados; e, o estudo de técnicas de realização em tecnologia digital CMOS de
circuitos de transcondutância para a implementação de filtros integrados analógicos em
tempo contínuo.
Na sequência deste estudo, apresentam-se e comparam-se duas estruturas de filtros
no espaço de estados, correspondentes a duas soluções alternativas para a realização de
um igualador adaptativo realizado por um filtro contínuo passa-tudo de terceira ordem,
para utilização num canal de leitura de dados em suporte magnético.
Como parte constituinte destes filtros, apresenta-se uma técnica de realização de
circuitos de transcondutância, e de realização de condensadores lineares usando matrizes
de transístores MOSFET para processamento de sinal em muito-alta-frequência realizada
em circuito integrado usando tecnologia digital CMOS submicrométrica. Apresentam-se
métodos de adaptação automática capazes de compensar os erros face aos valores nominais
dos componentes, devidos às tolerâncias inerentes ao processo de fabrico, para os
quais apresentamos os resultados de simulação e de medição experimental obtidos.
Na sequência deste estudo, resultou igualmente a apresentação de um circuito passível
de constituir uma solução para o controlo de posicionamento da cabeça de leitura
em sistemas de gravação/reprodução de dados em suporte magnético. O bloco proposto
é um filtro adaptativo de primeira ordem, com base nos mesmos circuitos de transcondutância
e técnicas de igualação propostos e utilizados na implementação do filtro adaptativo
de igualação do canal de leitura.
Este bloco de filtragem foi projectado e incluído num circuito integrado (Jaguar) de
controlo de posicionamento da cabeça de leitura realizado para a empresa ATMEL em
Colorado Springs, e incluído num produto comercial em parceria com uma empresa escocesa
utilizado em discos rígidos amovíveis.This thesis studies the design and behavior of continuous-time very-high-frequency
filters. The motivation of this work was the search for filtering solutions for the readchannel
in recording and reproduction of data on magnetic media systems, with costs and
consumption (total size less than 1 mm2 and consumption under 1mW/pole), lower than
the available circuits. Accordingly, as was done in this work, the rapid development of
microelectronics technology raised very significant efforts worldwide in order to investigate
new techniques for implementing such filters in monolithic integrated circuit, especially
in CMOS technology (Complementary Metal Oxide Semiconductor). We present
a comparative study on different hierarchical levels of the project, which led to the realization
and characterization of solutions with the desired characteristics.
In the first level, this study addresses the conceptual question of recording and
transmission of signal and the choice of good mathematical models for the processing of
information and minimization of error inherent in the approaches and in accordance with
the principles of the characterized physical devices.
The main work of this thesis is focused on the hierarchical levels of the architecture
of the read channel and the integrated circuit implementation of its main block - the filtering
block. At the architecture level of the read channel this work presents a comprehensive
study on existing methodologies of adaptation and signal recovery of data on
magnetic media. This project appears in the sequence of the proposed solution for a lowcost,
low consumption, low voltage, low complexity, using CMOS digital technology for
the performance of a DFE (Decision Feedback Equalization) based on the equalization of
the signal using integrated analog filters in continuous time.
At the project level of implementation of the filtering block and techniques for implementing
filters and its building components, it was concluded that the technique based
on transconductance circuits and capacitors, also known as gm-C filters is the most appropriate
for the implementation of very-high-frequency adaptive filters. We defined in
this lower level, two sub-levels of depth study for this thesis, namely: research and analysis
of optimal structures for the design of state-space filters, and the study of techniques for the design of transconductance cells in digital CMOS circuits for the implementation
of continuous time integrated analog filters.
Following this study, we present and compare two filtering structures operating in
the space of states, corresponding to two alternatives for achieving a realization of an
adaptive equalizer by the use of a continuous-time third order allpass filter, as part of a
read-channel for magnetic media devices.
As a constituent part of these filters, we present a technique for the realization of
transconductance circuits and for the implementation of linear capacitors using arrays of
MOSFET transistors for signal processing in very-high-frequency integrated circuits using
sub-micrometric CMOS technology. We present methods capable of automatic adjustment
and compensation for deviation errors in respect to the nominal values of the
components inherent to the tolerances of the fabrication process, for which we present
the simulation and experimental measurement results obtained.
Also as a result of this study, is the presentation of a circuit that provides a solution
for the control of the head positioning on recording/playback systems of data on magnetic
media. The proposed block is an adaptive first-order filter, based on the same transconductance
circuits and equalization techniques proposed and used in the implementation
of the adaptive filter for the equalization of the read channel.
This filter was designed and included in an integrated circuit (Jaguar) used to control
the positioning of the read-head done for ATMEL company in Colorado Springs, and
part of a commercial product used in removable hard drives fabricated in partnership with a Scottish company
Acoustical Communications for Wireless Downhole Telemetry Systems
This dissertation investigates the use of advanced acoustical communication techniques for wireless downhole telemetry systems. Using acoustic waves for downhole telemetry systems is investigated in order to replace the wired communication systems currently being used in oil and gas wells. While the acoustic technology offers great benefits, a clear understanding of its propagation aspects inside the wells is lacking. This dissertation describes a testbed that was designed to study the propagation of acoustic waves over production pipes. The wireless communication system was built using an acoustic transmitter, five connected segments of seven inch production pipes, and an acoustic receiver. The propagation experiments that were conducted on this testbed in order to characterize the channel behavior are explained as well. Moreover, the large scale statistics of the acoustic waves along the pipe string are described. Results of this work indicate that acoustic waves experience a frequency- dependent attenuation and dispersion over the pipe string. In addition, the testbed was modified by encasing one pipe segment in concrete in order to study the effect of concrete on wave propagation. The concrete was found to filter out many of the signal harmonics; accordingly, the acoustic waves experienced extra attenuation and dispersion. Signal processing techniques are also investigated to address the effects of multipaths and attenuation in the acoustic channel; results show great enhancements in signal qualities and the usefulness of these algorithms for downhole communication systems. Furthermore, to explore an alternative to vibrating the body of a cemented pipe string, a testbed was designed to investigate the propagation aspects of sound waves inside the interior of the production pipes. Results indicate that some low-frequency sound waves can travel for thousands of feet inside a cemented pipe string and can still be detected reliably
- …