A hierarchical architecture for increasing efficiency of large photovoltaic plants under non-homogeneous solar irradiation

Under non-homogeneous solar irradiation, photovoltaic (PV) panels receive different solar irradiance, resulting in a decrease in efficiency of the PV generation system. There are a few technical options to fix this issue that goes under the name of mismatch. One of these is the reconfiguration of the PV generation system, namely changing the connections of the PV panels from the initial configuration to the optimal one. Such technique has been widely considered for small systems, due to the excessive number of required switches. In this paper, the authors propose a new method for increasing the efficiency of large PV systems under non-homogeneous solar irradiation using Series-Parallel (SP) topology. In the first part of the paper, the authors propose a method containing two key points: a switching matrix to change the connection of PV panels based on SP topology and the proof that the SP-based reconfiguration method can increase the efficiency of the photovoltaic system up to 50%. In the second part, the authors propose the extension of the method proposed in the first part to improve the efficiency of large solar generation systems by means of a two-levels architecture to minimize the cost of fabrication of the switching matrix

Experimental tests to recover the photovoltaic power by battery system

The uncertainty and variability of the Renewable Energy Sources (RES) power plants within the power grid is an open issue. The present study focuses on the use of batteries to overcome the limitations associated with the photovoltaic inverter operation, trying to maximize the global energy produced. A set of switches, was placed between a few photovoltaic modules and a commercial inverter, capable to change configuration of the plant dynamically. Such system stores the power that the inverter is not able to let into the grid inside batteries. At the base of this optimization, there is the achievement of two main configurations in which the batteries and the photovoltaic modules are electrically connected in an appropriate manner as a function of inverter efficiency and thus solar radiation. A control board and the relative program, to change the configuration, was designed and implemented, based on the value of the measured radiation, current, batteries voltage, and calculated inverter efficiency. Finally from the cost and impact analysis we can say that, today the technology of lithium batteries, for this application, is still too expensive in comparison with lead-acid batteries

Power quality and electromagnetic compatibility: special report, session 2

The scope of Session 2 (S2) has been defined as follows by the Session Advisory Group and the Technical Committee: Power Quality (PQ), with the more general concept of electromagnetic compatibility (EMC) and with some related safety problems in electricity distribution systems. Special focus is put on voltage continuity (supply reliability, problem of outages) and voltage quality (voltage level, flicker, unbalance, harmonics). This session will also look at electromagnetic compatibility (mains frequency to 150 kHz), electromagnetic interferences and electric and magnetic fields issues. Also addressed in this session are electrical safety and immunity concerns (lightning issues, step, touch and transferred voltages). The aim of this special report is to present a synthesis of the present concerns in PQ&EMC, based on all selected papers of session 2 and related papers from other sessions, (152 papers in total). The report is divided in the following 4 blocks: Block 1: Electric and Magnetic Fields, EMC, Earthing systems Block 2: Harmonics Block 3: Voltage Variation Block 4: Power Quality Monitoring Two Round Tables will be organised: - Power quality and EMC in the Future Grid (CIGRE/CIRED WG C4.24, RT 13) - Reliability Benchmarking - why we should do it? What should be done in future? (RT 15

Power Quality Improvement and Low Voltage Ride through Capability in Hybrid Wind-PV Farms Grid-Connected Using Dynamic Voltage Restorer

© 2018 IEEE. Translations and content mining are permitted for academic research only. Personal use is also permitted, but republication/redistribution requires IEEE permission.This paper proposes the application of a dynamic voltage restorer (DVR) to enhance the power quality and improve the low voltage ride through (LVRT) capability of a three-phase medium-voltage network connected to a hybrid distribution generation system. In this system, the photovoltaic (PV) plant and the wind turbine generator (WTG) are connected to the same point of common coupling (PCC) with a sensitive load. The WTG consists of a DFIG generator connected to the network via a step-up transformer. The PV system is connected to the PCC via a two-stage energy conversion (dc-dc converter and dc-ac inverter). This topology allows, first, the extraction of maximum power based on the incremental inductance technique. Second, it allows the connection of the PV system to the public grid through a step-up transformer. In addition, the DVR based on fuzzy logic controller is connected to the same PCC. Different fault condition scenarios are tested for improving the efficiency and the quality of the power supply and compliance with the requirements of the LVRT grid code. The results of the LVRT capability, voltage stability, active power, reactive power, injected current, and dc link voltage, speed of turbine, and power factor at the PCC are presented with and without the contribution of the DVR system.Peer reviewe

Feasibility of a photovoltaic-thermoelectric generator: performance analysis and simulation results

This paper describes a theoretical approach to evaluate the performance of a hybrid solar system made with photovoltaic cells and thermoelectric (TE) modules. After a brief treatment of the integrated system, energy conversion and performance parameters are evaluated through numerical simulations depending on the global radiation and temperature distribution obtained by the Joint Research Center of the European Commission and of the National Renewable Energy Laboratory. The contribution of TE module to total energy seems significant in southern European towns and less substantial when the locations considered are very distant from the equator and show the possibility of using TE devices for energy production

Modeling and Simulation of Solar Photovoltaic Cell for the Generation of Electricity in UAE

This paper proposes the implementation of a circuit based simulation for a Solar Photovoltaic (PV) cell in order to get the maximum power output. The model is established based on the mathematical model of the PV module. As the PV cell is used to determine the physical and electrical behavior of the cell corresponding to environmental factors such as temperature and solar irradiance, this paper evaluates thirty years solar irradiation data in United Arab Emirates (UAE), also analyzes the performance parameters of PV cell for several locations. Based on the Shockley diode equation, a solar PV module is presented. However, to analyze the performance parameters, Solarex MSX 120, a typical 120W module is selected. The mathematical model for the chosen module is executed in Matlab. The consequence of this paper reflects the effects of variation of solar irradiation on PV cell within UAE. Conclusively, this paper determines the convenient places for implementing the large scale solar PV modules within UAE.Comment: To be published in 5th International Conference on Advances in Electrical Engineering (ICAEE-2019

Hydrogen at the rooftop: Compact CPV-hydrogen system to convert sunlight to hydrogen

Despite being highest potential energy source, solar intermittency and low power density make it difficult for solar energy to compete with the conventional power plants. Highly efficient concentrated photovoltaic (CPV) system provides best technology to be paired with the electrolytic hydrogen production, as a sustainable energy source with long term energy storage. However, the conventional gigantic design of CPV system limits its market and application to the open desert fields without any rooftop installation scope, unlike conventional PV. This makes CPV less popular among solar energy customers. This paper discusses the development of compact CPV-Hydrogen system for the rooftop application in the urban region. The in-house built compact CPV system works with hybrid solar tracking of 0.1° accuracy, ensured through proposed double lens collimator based solar tracking sensor. With PEM based electrolyser, the compact CPV-hydrogen system showed 28% CPV efficiency and 18% sunlight to hydrogen (STH) efficiency, for rooftop operation in tropical region of Singapore. For plant designers, the solar to hydrogen production rating of 217 kWhe/kgH2 has been presented with 15% STH daily average efficiency, recorded from the long term field operation of the syste