Backscattering UWB/UHF hybrid solutions for multi-reader multi-tag passive RFID systems

Ultra-wideband (UWB) technology is foreseen as a promising solution to overcome the limits of ultra-high frequency (UHF) techniques toward the development of green radio frequency identification (RFID) systems with low energy consumption and localization capabilities. While UWB techniques have been already employed for active tags, passive tags solutions are more appealing also due to their lower cost. With the fundamental requirement of maintaining backward compatibility in the RFID domain, we propose a hybrid UWB/UHF architecture to improve passive tag identification both in single-reader and multi-reader scenarios. We then develop two hybrid algorithms: the first one exploits the UWB signal to improve ISO/IEC 18000-6C UHF standard, while the other one exploits UWB to enhance a compressive sensing (CS) technique for tag identification in the multi-reader, multi-tag scenario. Both solutions are able to improve success rate and reading speed in the tag identification process and reduce the energy consumption. The multi-reader version of the proposed approaches is based on a cooperative scheme in order to manage reader-tag collisions and reader-reader collisions besides the typical tag-tag collisions. Furthermore, timing synchronization non-idealities are analyzed for the proposed solutions and simulation results reveal the effectiveness of the developed schemes

Persistent Q anti-collision algorithm for RFID

© Institution of Engineering and Technology.All Rights Reserved. In passive Radio Frequency Identification Systems (RFIDs), the interrogator should energise clients within range and use their backscattered replies to identify an inventory as quickly as possible. However, at the interrogator replies from two or more energised clients may collide and collided clients may not be identified. Therefore, collisions increase the number of timeslots needed to record an inventory. Reducing the number and frequency of collisions is an important and topical area research in RFID. Previously for passive Ultra High Frequency RFID the problem of collisions has been addressed using an ALOHA based protocol called the Q-Selection Algorithm. In this paper, a more efficient algorithm is presented that is shown to reduce the number of timeslots needed to record an inventory by approximately 30% when compared to the existing Q algorithm

On the Optimal Identification of Tag Sets in Time-Constrained RFID Configurations

In Radio Frequency Identification facilities the identification delay of a set of tags is mainly caused by the random access nature of the reading protocol, yielding a random identification time of the set of tags. In this paper, the cumulative distribution function of the identification time is evaluated using a discrete time Markov chain for single-set time-constrained passive RFID systems, namely those ones where a single group of tags is assumed to be in the reading area and only for a bounded time (sojourn time) before leaving. In these scenarios some tags in a set may leave the reader coverage area unidentified. The probability of this event is obtained from the cumulative distribution function of the identification time as a function of the sojourn time. This result provides a suitable criterion to minimize the probability of losing tags. Besides, an identification strategy based on splitting the set of tags in smaller subsets is also considered. Results demonstrate that there are optimal splitting configurations that reduce the overall identification time while keeping the same probability of losing tags

Stability of synchronous queued RFID networks

Queued Radio Frequency Identification (RFID) networks arise naturally in many applications, where tags are grouped into batches, and each batch must be processed before the next reading job starts. In these cases, the system must be able to handle all incoming jobs, keeping the queue backlogs bounded. This property is called stability. Besides, in RFID networks, it is common that some readers cannot operate at the same time, due to mutual interferences. This fact reduces the maximum traffic that readers can process since they have to share the channel. Synchronous networks share the channel using a TDMA approach. The goal of this work is to analytically determine whether a synchronous queued RFID network attains stable operation under a given incoming traffic. Stability depends on the service rate, which is characterized in this paper using an exact numerical method based on a recursive analytical approach, overcoming the limitations of previous works, which were based on simplifications. We also address different flow optimization problems, such as computing the maximum joint traffic that a network can process stably, selecting the minimal number of readers to process a given total load, or determining the optimal timeslot duration, which are novel in the RFID literature.This work was supported by the Project AIM, (AEI/FEDER, EU) under Grant TEC2016-76465-C2-1-R

DESIGN AUTOMATION FOR LOW POWER RFID TAGS

Radio Frequency Identification (RFID) tags are small, wireless devices capable of automated item identification, used in a variety of applications including supply chain management, asset management, automatic toll collection (EZ Pass), etc. However, the design of these types of custom systems using the traditional methods can take months for a hardware engineer to develop and debug. In this dissertation, an automated, low-power flow for the design of RFID tags has been developed, implemented and validated. This dissertation presents the RFID Compiler, which permits high-level design entry using a simple description of the desired primitives and their behavior in ANSI-C. The compiler has different back-ends capable of targeting microprocessor-based or custom hardware-based tags. For the hardware-based tag, the back-end automatically converts the user-supplied behavior in C to low power synthesizable VHDL optimized for RFID applications. The compiler also integrates a fast, high-level power macromodeling flow, which can be used to generate power estimates within 15% accuracy of industry CAD tools and to optimize the primitives and / or the behaviors, compared to conventional practices. Using the RFID Compiler, the user can develop the entire design in a matter of days or weeks. The compiler has been used to implement standards such as ANSI, ISO 18000-7, 18000-6C and 18185-7. The automatically generated tag designs were validated by targeting microprocessors such as the AD Chips EISC and FPGAs such as Xilinx Spartan 3. The corresponding ASIC implementation is comparable to the conventionally designed commercial tags in terms of the energy and area. Thus, the RFID Compiler permits the design of power efficient, custom RFID tags by a wider audience with a dramatically reduced design cycle

Stability of synchronous queued RFID networks

Queued Radio Frequency Identification (RFID) networks arise naturally in many applications, where tags are grouped into batches, and each batch must be processed before the next reading job starts. In these cases, the system must be able to handle all incoming jobs, keeping the queue backlogs bounded. This property is called stability. Besides, in RFID networks, it is common that some readers cannot operate at the same time, due to mutual interferences. This fact reduces the maximum traffic that readers can process since they have to share the channel. Synchronous networks share the channel using a TDMA approach. The goal of this work is to analytically determine whether a synchronous queued RFID network attains stable operation under a given incoming traffic. Stability depends on the service rate, which is characterized in this paper using an exact numerical method based on a recursive analytical approach, overcoming the limitations of previous works, which were based on simplifications. We also address different flow optimization problems, such as computing the maximum joint traffic that a network can process stably, selecting the minimal number of readers to process a given total load, or determining the optimal timeslot duration, which are novel in the RFID literature.Ministerio de Economía, Industria y Competitividad | Ref. TEC2016-76465-C2-1-

Using Hybrid Query Tree to Cope with Capture Effect in RFID Tag Identification

Tag collision is one of the important issues in RFID systems. Many algorithms were proposed to address this issue. One of these algorithms is Query Tree (QT) which is an effective method. In addition, RFID suffers from Capture Effect (CE). CE occurs when a reader identifies one tag in the presence of a collision. We consider this as a bad phenomenon for QT, because under CE reader will not identify all of collided tags. Besides, CE is good phenomenon for some algorithms like Dynamic Framed Slotted Aloha (DFSA), because it can identify one tag even in collision slots. So we combine QT and DFSA to improve the QT performance, then we evaluate our proposed algorithm, called Hybrid QT, to show that it outperforms other similar algorithm