An interleaved full nyquist high-speed DAC technique

A 9 bit 11 GS/s DAC is presented that achieves an SFDR of more than 50 dB across Nyquist and IM3 below 50 dBc across Nyquist. The DAC uses a two-times interleaved architecture to suppress spurs that typically limit DAC performance. Despite requiring two current-steering DACs for the interleaved architecture, the relative low demands on performance of these sub-DACs imply that they can be implemented in an area and power efficient way. Together with a quad-switching architecture to decrease demands on the power supply and bias generation and employing the multiplexer switches in triode, the total core area is only 0.04 mm2 while consuming 110 mW from a single 1.0 V supply

Low-power high-speed ADC design techniques in scaled CMOS process

The power consumption of a single-channel successive approximation register (SAR) analog-to-digital (ADC) tends to linearly increase with its sampling rate (f[subscript s]), when f[subscript s] is small. However, when f[subscript s] passes a certain point for a given technology node, the ADC power P increases at much higher rate and the normalized power efficiency (P/f[subscript s]) starts to degrade rapidly. To enhance the conversion speed of SAR ADC, while maintaining a good power efficiency, this thesis presents speed-enhancing techniques for SAR ADC in nano-scale CMOS technologies. First chapter presents a 2b/cycle hybrid SAR architecture with only 1 differential capacitor-DAC (CDAC). Unlike prior multi-bit/cycle SAR works that make use of only the DAC differential mode (DM) voltage, the proposed architecture exploits both the DM and the common mode (CM). By using two degrees of freedom, 2b/cycle conversion technique can boost the f[subscript s] of the ADC without any additional DAC arrays. High-speed ADCs can boost the conversion speed not only by increasing the f[subscript s] of a single-channel ADC, but also by time-interleaving multiple ADC sub-channels running at a lower rate. For an N-channel time-interleaved (TI) SAR ADC operating at f[subscript s], each sub-SAR channel only needs to operate at f[subscript s]=N. Therefore, each sub-SAR can operate in the linear power versus speed region, leading to a significant power saving compared to a single-channel ADC running at the same sampling rate. Despite of its power efficiency, TI-ADC suffers from mismatches among sub-ADC channels, including gain, offset, and timing mismatches. Among them, timing skew is one of the most difficult errors to calibrate as it is nontrivial to extract and its induced error depends on both the frequency and the amplitude of the input signal. Second chapter of this thesis presents a TI-SAR with a fast variance-based timing-skew calibration technique. It uses a single-comparator based window detector (WD) to calibrate the timing skew. The WD suppresses variance estimation errors and allow precise variance estimation from a significantly small number of samples. It has low-hardware cost and orders of magnitude faster convergence speed compared to prior variance-based timing-skew calibration technique. The last chapter presents another TI-SAR with mean absolute deviation (MAD) based timing-skew calibration technique. In addition to all the advantages presented with the fast variance-based timing-skew calibration technique, the proposed technique further reduces the digital computation power by 50% by eliminating the squaring operations, which are essential in variance-based calibration techniqueElectrical and Computer Engineerin

Design of Energy-Efficient A/D Converters with Partial Embedded Equalization for High-Speed Wireline Receiver Applications

As the data rates of wireline communication links increases, channel impairments such as skin effect, dielectric loss, fiber dispersion, reflections and cross-talk become more pronounced. This warrants more interest in analog-to-digital converter (ADC)-based serial link receivers, as they allow for more complex and flexible back-end digital signal processing (DSP) relative to binary or mixed-signal receivers. Utilizing this back-end DSP allows for complex digital equalization and more bandwidth-efficient modulation schemes, while also displaying reduced process/voltage/temperature (PVT) sensitivity. Furthermore, these architectures offer straightforward design translation and can directly leverage the area and power scaling offered by new CMOS technology nodes. However, the power consumption of the ADC front-end and subsequent digital signal processing is a major issue. Embedding partial equalization inside the front-end ADC can potentially result in lowering the complexity of back-end DSP and/or decreasing the ADC resolution requirement, which results in a more energy-effcient receiver. This dissertation presents efficient implementations for multi-GS/s time-interleaved ADCs with partial embedded equalization. First prototype details a 6b 1.6GS/s ADC with a novel embedded redundant-cycle 1-tap DFE structure in 90nm CMOS. The other two prototypes explain more complex 6b 10GS/s ADCs with efficiently embedded feed-forward equalization (FFE) and decision feedback equalization (DFE) in 65nm CMOS. Leveraging a time-interleaved successive approximation ADC architecture, new structures for embedded DFE and FFE are proposed with low power/area overhead. Measurement results over FR4 channels verify the effectiveness of proposed embedded equalization schemes. The comparison of fabricated prototypes against state-of-the-art general-purpose ADCs at similar speed/resolution range shows comparable performances, while the proposed architectures include embedded equalization as well

High-speed Time-interleaved Digital-to-Analog Converter (TI-DAC) for Self-Interference Cancellation Applications

Nowadays, the need for higher data-rate is constantly growing to enhance the quality of the daily communication services. The full-duplex (FD) communication is exemplary method doubling the data-rate compared to half-duplex one. However, part of the strong output signal of the transmitter interferes to the receiver-side because they share the same antenna with limited attenuation and, as a result, the receiver’s performance is corrupted. Hence, it is critical to remove the leakage signal from the receiver’s path by designing another block called self-interference cancellation (SIC). The main goal of this dissertation is to develop the SIC block embedded in the current-mode FD receivers. To this end, the regenerated cancellation current signal is fed to the inputs of the base-band filter and after the mixer of a (direct-conversion) current-mode FD receiver. Since the pattern of the transmitter (the digital signal generated by DSP) is known, a high-speed digital-to-Analog converter (DAC) with medium-resolution can perfectly suppress main part of the leakage on the receiver path. A capacitive DAC (CDAC) is chosen among the available solutions because it is compatible with advanced CMOS technology for high-speed application and the medium-resolution designs. Although the main application of the design is to perform the cancellation, it can also be employed as a stand-alone DAC in the Analog (I/Q) transmitter. The SIC circuitry includes a trans-impedance amplifier (TIA), two DACs, high-speed digital circuits, and built-in-self-test section (BIST). According to the available specification for full-duplex communication system, the resolution and working frequency of the CDAC are calculated (designed) equal to 10-bit (3 binary+ 2 binary + 5 thermometric) and 1GHz, respectively. In order to relax the design of the TIA (settling time of the DAC), the CDAC implements using 2-way time-interleaved (TI) manner (the effective SIC frequency equals 2GHz) without using any calibration technique. The CDAC is also developed with the split-capacitor technique to lower the negative effects of the conventional binary-weighted DAC. By adding one extra capacitor on the left-side of the split-capacitor, LSB-side, the value of the split-capacitor can be chosen as an integer value of the unit capacitor. As a result, it largely enhances the linearity of the CADC and cancellation performance. If the block works as a stand-alone DAC with non-TI mode, the digital input code representing a Sinus waveform with an amplitude 1dB less than full-scale and output frequency around 10.74MHz, chosen by coherent sampling rule, then the ENOB, SINAD, SFDR, and output signal are 9.4-bit, 58.2 dB, 68.4dBc, and -9dBV. The simulated value of the |DNL| (static linearity) is also less than 0.7. The similar simulation was done in the SIC mode while the capacitive-array woks in the TI mode and cancellation current is set to the full-scale. Hence, the amount of cancelling the SI signal at the output of the TIA, SNDR, SFDR, SNDRequ. equals 51.3dB, 15.1 dB, 24dBc, 66.4 dB. The designed SIC cannot work as a closed-loop design. The layout was optimally drawn in order to minimize non-linearity, the power-consumption of the decoders, and reduce the complexity of the DAC. By distributing the thermometric cells across the array and using symmetrical switching scheme, the DAC is less subjected to the linear and gradient effect of the oxide. Based on the post-layout simulation results, the deviation of the design after drawing the layout is studied. To compare the results of the schematic and post-layout designs, the exact conditions of simulation above (schematic simulations) are used. When the block works as a stand-alone CDAC, the ENOB, SINAD, SFDR are 8.5-bit, 52.6 dB, 61.3 dBc. The simulated value of the |DNL| (static linearity) is also limited to 1.3. Likewise, the SI signal at the output of the TIA, SNDR, SFDR, SNDRequ. are equal to 44dB, 11.7 dB, 19 dBc, 55.7 dB

Design and Analysis of a Low-Power 8-Bit 500 KS/S SAR ADC for Bio-Medical Implant Devices

This thesis project involves the design and analysis of an 8-bit Successive Approximation Register (SAR) Analog to Digital Convertor (ADC), designed for low- power applications such as bio-medical implants. The sampling rate for this ADC is 500 KS/s. The power consumption for the whole SAR ADC system was measured to be 2.1 uW. The novelty of this project is the proposal of an extremely energy efficient comparator architecture. The result is the design of a final ADC with reasonable sampling speed, accuracy and low power consumption. In this project, all the different subsystems have been designed at the transistor level with 45 nm CMOS technology. The logical circuit was designed using Verilog language. It was then synthesized and integrated in the overall system

All Digital, Background Calibration for Time-Interleaved and Successive Approximation Register Analog-to-Digital Converters

The growth of digital systems underscores the need to convert analog information to the digital domain at high speeds and with great accuracy. Analog-to-Digital Converter (ADC) calibration is often a limiting factor, requiring longer calibration times to achieve higher accuracy. The goal of this dissertation is to perform a fully digital background calibration using an arbitrary input signal for A/D converters. The work presented here adapts the cyclic Split-ADC calibration method to the time interleaved (TI) and successive approximation register (SAR) architectures. The TI architecture has three types of linear mismatch errors: offset, gain and aperture time delay. By correcting all three mismatch errors in the digital domain, each converter is capable of operating at the fastest speed allowed by the process technology. The total number of correction parameters required for calibration is dependent on the interleaving ratio, M. To adapt the Split-ADC method to a TI system, 2M+1 half-sized converters are required to estimate 3(2M+1) correction parameters. This thesis presents a 4:1 Split-TI converter that achieves full convergence in less than 400,000 samples. The SAR architecture employs a binary weight capacitor array to convert analog inputs into digital output codes. Mismatch in the capacitor weights results in non-linear distortion error. By adding redundant bits and dividing the array into individual unit capacitors, the Split-SAR method can estimate the mismatch and correct the digital output code. The results from this work show a reduction in the non-linear distortion with the ability to converge in less than 750,000 samples

A 16-b 10Msample/s Split-Interleaved Analog to Digital Converter

This work describes the integrated circuit design of a 16-bit, 10Msample/sec, combination ‘split’ interleaved analog to digital converter. Time interleaving of analog to digital converters has been used successfully for many years as a technique to achieve faster speeds using multiple identical converters. However, efforts to achieve higher resolutions with this technique have been difficult due to the precise matching required of the converter channels. The most troublesome errors in these types of converters are gain, offset and timing differences between channels. The ‘split ADC’ is a new concept that allows the use of a deterministic, digital, self calibrating algorithm. In this approach, an ADC is split into two paths, producing two output codes from the same input sample. The difference of these two codes is used as the calibration signal for an LMS error estimation algorithm that drives the difference error to zero. The ADC is calibrated when the codes are equal and the output is taken as the average of the two codes. The ‘split’ ADC concept and interleaved architecture are combined in this IC design to form the core of a high speed, high resolution, and self-calibrating ADC system. The dual outputs are used to drive a digital calibration engine to correct for the channel mismatch errors. This system has the speed benefits of interleaving while maintaining high resolution. The hardware for the algorithm as well as the ADC can be implemented in a standard 0.25um CMOS process, resulting in a relatively inexpensive solution. This work is supported by grants from Analog Devices Incorporated (ADI) and the National Science Foundation (NSF)

Design Techniques for High-Performance SAR A/D Converters

The design of electronics needs to account for the non-ideal characteristics of the device technologies used to realize practical circuits. This is particularly important in mixed analog-digital design since the best device technologies are very different for digital compared to analog circuits. One solution for this problem is to use a calibration correction approach to remove the errors introduced by devices, but this adds complexity and power dissipation, as well as reducing operation speed, and so must be optimised. This thesis addresses such an approach to improve the performance of certain types of analog-to-digital converter (ADC) used in advanced telecommunications, where speed, accuracy and power dissipation currently limit applications. The thesis specifically focuses on the design of compensation circuits for use in successive approximation register (SAR) ADCs. ADCs are crucial building blocks in communication systems, in general, and for mobile networks, in particular. The recently launched fifth generation of mobile networks (5G) has required new ADC circuit techniques to meet the higher speed and lower power dissipation requirements for 5G technology. The SAR has become one of the most favoured architectures for designing high-performance ADCs, but the successive nature of the circuit operation makes it difficult to reach ∼GS/s sampling rates at reasonable power consumption. Here, two calibration techniques for high-performance SAR ADCs are presented. The first uses an on-chip stochastic-based mismatch calibration technique that is able to accurately compute and compensate for the mismatch of a capacitive DAC in a SAR ADC. The stochastic nature of the proposed calibration method enables determination of the mismatch of the CAPDAC with a resolution much better than that of the DAC. This allows the unit capacitor to scale down to as low as 280aF for a 9-bit DAC. Since the CAP-DAC causes a large part of the overall dynamic power consumption and directly determines both the sizes of the driving and sampling switches and the size of the input capacitive load of the ADC and the kT/C noise power, a small CAP-DAC helps the power efficiency. To validate the proposed calibration idea, a 10-bit asynchronous SAR ADC was fabricated in 28-nm CMOS. Measurement results show that the proposed stochastic calibration improves the ADC’s SFDR and SNDR by 14.9 dB, 11.5 dB, respectively. After calibration, the fabricated SAR ADC achieves an ENOB of 9.14 bit at a sampling rate of 85 MS/s, resulting in a Walden FoM of 10.9 fJ/c-s. The second calibration technique is a timing-skew calibration for a time-interleaved (TI) SAR ADC that calibrates/computes the inter-channel timing and offset mismatch simultaneously. Simulation results show the effectiveness of this calibration method. When used together, the proposed mismatch calibration technique and the timing-skew calibration technique enables a TI SAR ADC to be designed that can achieve a sampling rate of ∼GS/s with 10-bit resolution and a power consumption as low as ∼10mW; specifications that satisfy the requirements of 5G technology