Gunn diodes and devices (bibliography for 1978-1980)

A listing of about 500 works from Soviet and foreign scientific literature on Gunn diodes and devices based on them is presented. The bibliography includes publications in which various questions pertinent to all (or several) types of semiconductor instruments in the superhigh frequency range are mentioned. A subject index is included

Design and characterisation of millimetre wave planar Gunn diodes and integrated circuits

Heterojunction planar Gunn devices were first demonstrated by Khalid et al in 2007. This new design of Gunn device, or transferred electron device, was based on the well-established material system of GaAs as the oscillation media. The design did not only breakthrough the frequency record of GaAs for conventional Gunn devices, but also has several advantages over conventional Gunn devices, such as the possibility of making multiple oscillators on a single chip and compatibility with monolithic integrated circuits. However, these devices faced the challenge of producing high enough RF power for practical applications and circuit technology for integration. This thesis describes systematic work on the design and characterisations of planar Gunn diodes and the associated millimetre-wave circuits for RF signal power enhancement. Focus has been put on improving the design of planar Gunn diodes and developing high performance integrated millimetre-wave circuits for combining multiple Gunn diodes. Improvement of device design has been proved to be one of the key methods to increase the signal power. By introducing additional δ-doping layers, electron concentration in the channel increases and better Gunn domain formation is achieved, therefore higher RF power and frequency are produced. Combining multiple channels in the vertical direction within devices is another effective way to increase the output signal power as well as DC-to-RF conversion efficiency. In addition, an alternative material system, i.e. In0.23Ga0.77As, has also been studied for this purpose. Planar passive components, such as resonators, couplers, low pass filters (LPFs), and power combiners with high performance over 100 GHz have been developed. These components can be smoothly integrated with planar Gunn diodes for compact planar Gunn oscillators, and therefore contribute to RF power enhancement. In addition, several new measurement techniques for characterising oscillators and passive devices have also been developed during this work and will be included in this thesis

Design of Circuits to enhances the performace of high frequency planar Gunn diodes

The project contains adventurous research, with an aim to understand and design a planar Gunn diode with a novel integrated circuit configuration to extract the 2nd harmonic. This will potentially enhance the Gunn diode as a high frequency source towards frequencies in excess of 600 GHz. The RF performance from the above integrated circuit was achieved by design and simulation of radial and diamond stub resonators, which were used to short the fundamental oscillation frequency while allowing the second harmonic frequency to pass through to the load. The diamond stub resonator is a new configuration offering a number of advantages which include a higher loaded quality factor and occupies 55% less chip area than a comparable radial stub resonator. The designed novel circuits with integrated planar Gunn diode were fabricated using microwave monolithic integrated circuits (MMIC) technology at the James Watt Nanofabrication centre in Glasgow University. Full DC and microwave characterisation of the diodes and integrated circuits with diodes was carried out using a semiconductor analyser, network analyser (10 MHz to 110GHz) and spectrum analyser (10 MHz to 125GHz). The microwave measurements were carried out at the high frequency RF laboratories in Glasgow University. Both GaAs and InP based Gunn diodes were characterised and RF characterisation work showed that higher fundamental frequencies could be obtained from Gunn diodes fabricated on InGaAs on a lattice matched InP substrate. Planar Gunn diodes with an anode to cathode spacing of 4 microns giving a fundamental frequency of oscillation of 60 GHz were fabricated as an integrated circuit with coplanar waveguide (CPW) circuit elements to extract the second harmonic. A second harmonic frequency of 120 GHz with an RF output power of -14.11 dBm was extracted with very good fundamental frequency suppression. To the authors knowledge this was the first time second harmonic frequencies have been extracted from a planar Gunn diode technology. Aluminium gallium arsenide (AlGaAs) planar Gunn diodes were also designed with an integrated series inductor to match the diode at the fundamental frequency to obtain higher RF output powers. Devices with a 1 micron anode to cathode separation gave the highest fundamental oscillation frequency of 121 GHz the highest reported for a GaAs based Gunn diode and with an RF output power of -9 dBm. These circuits will have potential applications in secure communications, terahertz imaging etc. The research programme was in collaboration with the University of Glasgowwould like to thank the staff of the James Watt Nanofabrication Centre at the University of Glasgow for help in fabricating the devices which is reported in this thesis. ‘Part of this work was supported by ESPRC through EP/H011862/1, and EP/H012966/1

A 12 GHz satellite video receiver: Low noise, low cost prototype model for TV reception from broadcast satellites

A 12-channel synchronous phase lock video receiver consisting of an outdoor downconverter unit and an indoor demodulator unit was developed to provide both low noise performance and low cost in production quantities of 1000 units. The prototype receiver can be mass produced at a cost under $1540 without sacrificing system performance. The receiver also has the capability of selecting any of the twelve assigned satellite broadcast channels in the frequency range 11.7 to 12.2 GHz

Index to NASA Tech Briefs, 1975

This index contains abstracts and four indexes--subject, personal author, originating Center, and Tech Brief number--for 1975 Tech Briefs

The Third International Symposium on Space Terahertz Technology: Symposium proceedings

Papers from the symposium are presented that are relevant to the generation, detection, and use of the terahertz spectral region for space astronomy and remote sensing of the Earth's upper atmosphere. The program included thirteen sessions covering a wide variety of topics including solid-state oscillators, power-combining techniques, mixers, harmonic multipliers, antennas and antenna arrays, submillimeter receivers, and measurement techniques

Solid state Ku-band spacecraft transmitters

A transmitter is considered that consists of GaAs IMPATT and Read diodes operating in a microstrip circuit environment to provide amplification with a minimum of 63 db small signal gain and a minimum compressed gain at 5 W output of 57 db. Reported are Schottky-Read diode design and fabrication, microstrip and circulator optimization, preamplifier development, power amplifier development, dc-to-dc converter design, and integration of the breadboard transmitter modules. A four-stage power amplifier in cascade with a three-stage preamplifier had an overall gain of 56.5 db at 13.5 GHz with a power output of 4.5 W. A single-stage Read amplifier delivered 5.9 W with 4 db gain at 22% efficiency

Microwave and Millimeter Wave Techniques

Contains reports on three research projects.Joint Services Electronics Program (Contract DAAB07-71-C-0300)National Science Foundation (Grant GP-40485X

Finite difference time domain analysis of microstrip antenna-circuit modules

Compact microstrip antenna-circuit modules, which could be used as front-ends for future wireless systems applications, require electromagnetic modelling due to the close interaction of the circuit with the antenna. Spectrum crowding and EMC/EMI issues call for modelling of the radiation of such modules. Coupling through fringing fields and the nonlinearities of active devices must be addressed. In this work, the FDTD method was used because it can provide the framework for inclusion of circuit elements in a full wave calculation. A software tool was developed and validated based on this method. The modules studied were chosen due to their compactness and their merit as system components. A module with simultaneous transmit-receive operation integrating an active circulator (using amplifiers in a ring-like arrangement) and a quarter wavelength antenna was analysed. Coupling effects were identified and their impact on the radiation patterns was shown. Electronically tuneable microstrip patch antennas using varactor diodes were also studied. Tuning range and harmonic radiation were demonstrated. Single and dual device Gunn oscillator antennas were analysed and their radiation patterns were calculated for the first time. All of our results were in agreement with experimental findings

The present situation and forecasts of semiconductor elements performance within the microwave range, 1970-1985

The present situation and possible developments over the period 1970-1985 for active semiconductor elements in the microwave range are outlined. After a short historical survey of FT techniques, the following are discussed: Generation, power amplification, amplification of small signals, frequency conversion, detection, electronic signal control and integrated microwave circuits