A low-speed BIST framework for high-performance circuit testing

Testing of high performance integrated circuits is becoming increasingly a challenging task owing to high clock frequencies. Often testers are not able to test such devices due to their limited high frequency capabilities. In this article we outline a design-for-test methodology such that high performance devices can be tested on relatively low performance testers. In addition, a BIST framework is discussed based on this methodology. Various implementation aspects of this technique are also addresse

Quiescent current testing of CMOS data converters

Power supply quiescent current (IDDQ) testing has been very effective in VLSI circuits designed in CMOS processes detecting physical defects such as open and shorts and bridging defects. However, in sub-micron VLSI circuits, IDDQ is masked by the increased subthreshold (leakage) current of MOSFETs affecting the efficiency of I¬DDQ testing. In this work, an attempt has been made to perform robust IDDQ testing in presence of increased leakage current by suitably modifying some of the test methods normally used in industry. Digital CMOS integrated circuits have been tested successfully using IDDQ and IDDQ methods for physical defects. However, testing of analog circuits is still a problem due to variation in design from one specific application to other. The increased leakage current further complicates not only the design but also testing. Mixed-signal integrated circuits such as the data converters are even more difficult to test because both analog and digital functions are built on the same substrate. We have re-examined both IDDQ and IDDQ methods of testing digital CMOS VLSI circuits and added features to minimize the influence of leakage current. We have designed built-in current sensors (BICS) for on-chip testing of analog and mixed-signal integrated circuits. We have also combined quiescent current testing with oscillation and transient current test techniques to map large number of manufacturing defects on a chip. In testing, we have used a simple method of injecting faults simulating manufacturing defects invented in our VLSI research group. We present design and testing of analog and mixed-signal integrated circuits with on-chip BICS such as an operational amplifier, 12-bit charge scaling architecture based digital-to-analog converter (DAC), 12-bit recycling architecture based analog-to-digital converter (ADC) and operational amplifier with floating gate inputs. The designed circuits are fabricated in 0.5 μm and 1.5 μm n-well CMOS processes and tested. Experimentally observed results of the fabricated devices are compared with simulations from SPICE using MOS level 3 and BSIM3.1 model parameters for 1.5 μm and 0.5 μm n-well CMOS technologies, respectively. We have also explored the possibility of using noise in VLSI circuits for testing defects and present the method we have developed

A design for testability study on a high performance automatic gain control circuit.

A comprehensive testability study on a commercial automatic gain control circuit is presented which aims to identify design for testability (DfT) modifications to both reduce production test cost and improve test quality. A fault simulation strategy based on layout extracted faults has been used to support the study. The paper proposes a number of DfT modifications at the layout, schematic and system levels together with testability. Guidelines that may well have generic applicability. Proposals for using the modifications to achieve partial self test are made and estimates of achieved fault coverage and quality levels presente

A Low Speed BIST Framework for High Speed Circuit Testing

Testing of high performance integrated circuits is becoming increasingly a challenging task owing to high clock frequencies. Often testers are not able to test such devices due to their limited high frequency capabilities. In this article we outline a design-for-test methodology such that high performance devices can be tested on relatively low performance testers. In addition, a BIST framework is discussed based on this methodology. Various implementation aspects of this technique are also addresse

Iddq testing of a CMOS 10-bit charge scaling digital-to-analog converter

This work presents an effective built-in current sensor (BICS), which has a very small impact on the performance of the circuit under test (CUT). The proposed BICS works in two-modes the normal mode and the test mode. In the normal mode the BICS is isolated from the CUT due to which there is no performance degradation of the CUT. In the testing mode, our BICS detects the abnormal current caused by permanent manufacturing defects. Further more our BICS can also distinguish the type of defect induced (Gate-source short, source-drain short and drain-gate short). Our BICS requires neither an external voltage source nor current source. Hence the BICS requires less area and is more efficient than the conventional current sensors. The circuit under test is a 10-bit digital to analog converter using charge-scaling architecture

Design for testability of a latch-based design

Abstract. The purpose of this thesis was to decrease the area of digital logic in a power management integrated circuit (PMIC), by replacing selected flip-flops with latches. The thesis consists of a theory part, that provides background theory for the thesis, and a practical part, that presents a latch register design and design for testability (DFT) method for achieving an acceptable level of manufacturing fault coverage for it. The total area was decreased by replacing flip-flops of read-write and one-time programmable registers with latches. One set of negative level active primary latches were shared with all the positive level active latch registers in the same register bank. Clock gating was used to select which latch register the write data was loaded to from the primary latches. The latches were made transparent during the shift operation of partial scan testing. The observability of the latch register clock gating logic was improved by leaving the first bit of each latch register as a flip-flop. The controllability was improved by inserting control points. The latch register design, developed in this thesis, resulted in a total area decrease of 5% and a register bank area decrease of 15% compared to a flip-flop-based reference design. The latch register design manages to maintain the same stuck-at fault coverage as the reference design.Salpaperäisen piirin testattavuuden suunnittelu. Tiivistelmä. Tämän opinnäytetyön tarkoituksena oli pienentää digitaalisen logiikan pinta-alaa integroidussa tehonhallintapiirissä, korvaamalla valitut kiikut salpapiireillä. Opinnäytetyö koostuu teoriaosasta, joka antaa taustatietoa opinnäytetyölle, ja käytännön osuudesta, jossa esitellään salparekisteripiiri ja testattavuussuunnittelun menetelmä, jolla saavutettiin riittävän hyvä virhekattavuus salparekisteripiirille. Kokonaispinta-alaa pienennettiin korvaamalla luku-kirjoitusrekistereiden ja kerran ohjelmoitavien rekistereiden kiikut salpapiireillä. Yhdet negatiivisella tasolla aktiiviset isäntä-salpapiirit jaettiin kaikkien samassa rekisteripankissa olevien positiivisella tasolla aktiivisten salparekistereiden kanssa. Kellon portittamisella valittiin mihin salparekisteriin kirjoitusdata ladattiin yhteisistä isäntä-salpapireistä. Osittaisessa testipolkuihin perustuvassa testauksessa salpapiirit tehtiin läpinäkyviksi siirtooperaation aikana. Salparekisterin kellon portituslogiikan havaittavuutta parannettiin jättämällä jokaisen salparekisterin ensimmäinen bitti kiikuksi. Ohjattavuutta parannettiin lisäämällä ohjauspisteitä. Salparekisteripiiri, joka suunniteltiin tässä diplomityössä, pienensi kokonaispinta-alaa 5 % ja rekisteripankin pinta-alaa 15 % verrattuna kiikkuperäiseen vertailupiiriin. Salparekisteripiiri onnistuu pitämään saman juuttumisvikamallin virhekattavuuden kuin vertailupiiri

Programmable CMOS Analog-to-Digital Converter Design and Testability

In this work, a programmable second order oversampling CMOS delta-sigma analog-to-digital converter (ADC) design in 0.5µm n-well CMOS processes is presented for integration in sensor nodes for wireless sensor networks. The digital cascaded integrator comb (CIC) decimation filter is designed to operate at three different oversampling ratios of 16, 32 and 64 to give three different resolutions of 9, 12 and 14 bits, respectively which impact the power consumption of the sensor nodes. Since the major part of power consumed in the CIC decimator is by the integrators, an alternate design is introduced by inserting coder circuits and reusing the same integrators for different resolutions and oversampling ratios to reduce power consumption. The measured peak signal-to-noise ratio (SNR) for the designed second order delta-sigma modulator is 75.6dB at an oversampling ratio of 64, 62.3dB at an oversampling ratio of 32 and 45.3dB at an oversampling ratio of 16. The implementation of a built-in current sensor (BICS) which takes into account the increased background current of defect-free circuits and the effects of process variation on ΔIDDQ testing of CMOS data converters is also presented. The BICS uses frequency as the output for fault detection in CUT. A fault is detected when the output frequency deviates more than ±10% from the reference frequency. The output frequencies of the BICS for various model parameters are simulated to check for the effect of process variation on the frequency deviation. A design for on-chip testability of CMOS ADC by linear ramp histogram technique using synchronous counter as register in code detection unit (CDU) is also presented. A brief overview of the histogram technique, the formulae used to calculate the ADC parameters, the design implemented in 0.5µm n-well CMOS process, the results and effectiveness of the design are described. Registers in this design are replaced by 6T-SRAM cells and a hardware optimized on-chip testability of CMOS ADC by linear ramp histogram technique using 6T-SRAM as register in CDU is presented. The on-chip linear ramp histogram technique can be seamlessly combined with ΔIDDQ technique for improved testability, increased fault coverage and reliable operation