1,464 research outputs found
Recommended from our members
Noise shaping Asynchronous SAR ADC based time to digital converter
Time-to-digital converters (TDCs) are key elements for the digitization of timing information in modern mixed-signal circuits such as digital PLLs, DLLs, ADCs, and on-chip jitter-monitoring circuits. Especially, high-resolution TDCs are increasingly employed in on-chip timing tests, such as jitter and clock skew measurements, as advanced fabrication technologies allow fine on-chip time resolutions. Its main purpose is to quantize the time interval of a pulse signal or the time interval between the rising edges of two clock signals. Similarly to ADCs, the performance of TDCs are also primarily characterized by Resolution, Sampling Rate, FOM, SNDR, Dynamic Range and DNL/INL. This work proposes and demonstrates 2nd order noise shaping Asynchronous SAR ADC based TDC architecture with highest resolution of 0.25 ps among current state of art designs with respect to post-layout simulation results. This circuit is a combination of low power/High Resolution 2nd Order Noise Shaped Asynchronous SAR ADC backend with simple Time to Amplitude converter (TAC) front-end and is implemented in 40nm CMOS technology. Additionally, special emphasis is given on the discussion on various current state of art TDC architectures.Electrical and Computer Engineerin
A jittered-sampling correction technique for ADCs
In Analogue to Digital Converters (ADCs) jittered sampling raises the noise floor; this leads to a decrease in its Signal to Noise ratio (SNR) and its effective number of bits (ENOB). This research studies a technique that compensate for the effects of sampling with a jittered clock. A thorough understanding of sampling in various data converters is complied
Recommended from our members
Built-in self test of RF subsystems
textWith the rapid development of wireless and wireline communications, a variety of new standards and applications are emerging in the marketplace. In order to achieve higher levels of integration, RF circuits are frequently embedded into System on Chip (SoC) or System in Package (SiP) products. These developments, however, lead to new challenges in manufacturing test time and cost. Use of traditional RF test techniques requires expensive high frequency test instruments and long test time, which makes test one of the bottlenecks for reducing IC costs. This research is in the area of built-in self test technique for RF subsystems. In the test approach followed in this research, on-chip detectors are used to calculate circuits specifications, and data converters are used to collect the data for analysis by an on-chip processor. A novel on-chip amplitude detector has been designed and optimized for RF circuit specification test. By using on-chip detectors, both the system performance and specifications of the individual components can be accurately measured. On-chip measurement results need to be collected by Analog to Digital Converters (ADCs). A novel time domain, low power ADC has been designed for this purpose. The ADC architecture is based on a linear voltage controlled delay line. Using this structure results in a linear transfer function for the input dependent delay. The time delay difference is then compared to a reference to generate a digital code. Two prototype test chips were fabricated in commercial CMOS processes. One is for the RF transceiver front end with on-chip detectors; the other is for the test ADC. The 940MHz RF transceiver front-end was implemented with on-chip detectors in a 0.18 [micrometer] CMOS technology. The chips were mounted onto RF Printed Circuit Boards (PCBs), with tunable power supply and biasing knobs. The detector was characterized with measurements which show that the detector keeps linear performance over a wide input amplitude range of 500mV. Preliminary simulation and measurements show accurate transceiver performance prediction under process variations. A 300MS/s 6 bit ADC was designed using the novel time domain architecture in a 0.13 [micrometer] standard digital CMOS process. The simulation results show 36.6dB Signal to Noise Ratio (SNR), 34.1dB Signal to Noise and Distortion Ratio (SNDR) for 99MHz input, Differential Non-Linearity (DNL)<0.2 Least Significant Bit (LSB), and Integral Non-Linearity (INL)<0.5LSB. Overall chip power is 2.7mW with a 1.2V power supply. The built-in detector RF test was extended to a full transceiver RF front end test with a loop-back setup, so that measurements can be made to verify the benefits of the technique. The application of the approach to testing gain, linearity and noise figure was investigated. New detector types are also evaluated. In addition, the low-power delay-line based ADC was characterized and improved to facilitate gathering of data from the detector. Several improved ADC structures at the system level are also analyzed. The built-in detector based RF test technique enables the cost-efficient test for SoCs.Electrical and Computer Engineerin
Design of Energy-Efficient A/D Converters with Partial Embedded Equalization for High-Speed Wireline Receiver Applications
As the data rates of wireline communication links increases, channel impairments such as skin effect, dielectric loss, fiber dispersion, reflections and cross-talk become more pronounced. This warrants more interest in analog-to-digital converter (ADC)-based serial link receivers, as they allow for more complex and flexible back-end digital signal processing (DSP) relative to binary or mixed-signal receivers. Utilizing this back-end DSP allows for complex digital equalization and more bandwidth-efficient modulation schemes, while also displaying reduced process/voltage/temperature (PVT) sensitivity. Furthermore, these architectures offer straightforward design translation and can directly leverage the area and power scaling offered by new CMOS technology nodes. However, the power consumption of the ADC front-end and subsequent digital signal processing is a major issue. Embedding partial equalization inside the front-end ADC can potentially result in lowering the complexity of back-end DSP and/or decreasing the ADC resolution requirement, which results in a more energy-effcient receiver. This dissertation presents efficient implementations for multi-GS/s time-interleaved ADCs with partial embedded equalization. First prototype details a 6b 1.6GS/s ADC with a novel embedded redundant-cycle 1-tap DFE structure in 90nm CMOS. The other two prototypes explain more complex 6b 10GS/s ADCs with efficiently embedded feed-forward equalization (FFE) and decision feedback equalization (DFE) in 65nm CMOS. Leveraging a time-interleaved successive approximation ADC architecture, new structures for embedded DFE and FFE are proposed with low power/area overhead. Measurement results over FR4 channels verify the effectiveness of proposed embedded equalization schemes. The comparison of fabricated prototypes against state-of-the-art general-purpose ADCs at similar speed/resolution range shows comparable performances, while the proposed architectures include embedded equalization as well
- …