Algorithms for Power Aware Testing of Nanometer Digital ICs

At-speed testing of deep-submicron digital very large scale integrated (VLSI) circuits has become mandatory to catch small delay defects. Now, due to continuous shrinking of complementary metal oxide semiconductor (CMOS) transistor feature size, power density grows geometrically with technology scaling. Additionally, power dissipation inside a digital circuit during the testing phase (for test vectors under all fault models (Potluri, 2015)) is several times higher than its power dissipation during the normal functional phase of operation. Due to this, the currents that flow in the power grid during the testing phase, are much higher than what the power grid is designed for (the functional phase of operation). As a result, during at-speed testing, the supply grid experiences unacceptable supply IR-drop, ultimately leading to delay failures during at-speed testing. Since these failures are specific to testing and do not occur during functional phase of operation of the chip, these failures are usually referred to false failures, and they reduce the yield of the chip, which is undesirable. In nanometer regime, process parameter variations has become a major problem. Due to the variation in signalling delays caused by these variations, it is important to perform at-speed testing even for stuck faults, to reduce the test escapes (McCluskey and Tseng, 2000; Vorisek et al., 2004). In this context, the problem of excessive peak power dissipation causing false failures, that was addressed previously in the context of at-speed transition fault testing (Saxena et al., 2003; Devanathan et al., 2007a,b,c), also becomes prominent in the context of at-speed testing of stuck faults (Maxwell et al., 1996; McCluskey and Tseng, 2000; Vorisek et al., 2004; Prabhu and Abraham, 2012; Potluri, 2015; Potluri et al., 2015). It is well known that excessive supply IR-drop during at-speed testing can be kept under control by minimizing switching activity during testing (Saxena et al., 2003). There is a rich collection of techniques proposed in the past for reduction of peak switching activity during at-speed testing of transition/delay faults ii in both combinational and sequential circuits. As far as at-speed testing of stuck faults are concerned, while there were some techniques proposed in the past for combinational circuits (Girard et al., 1998; Dabholkar et al., 1998), there are no techniques concerning the same for sequential circuits. This thesis addresses this open problem. We propose algorithms for minimization of peak switching activity during at-speed testing of stuck faults in sequential digital circuits under the combinational state preservation scan (CSP-scan) architecture (Potluri, 2015; Potluri et al., 2015). First, we show that, under this CSP-scan architecture, when the test set is completely specified, the peak switching activity during testing can be minimized by solving the Bottleneck Traveling Salesman Problem (BTSP). This mapping of peak test switching activity minimization problem to BTSP is novel, and proposed for the first time in the literature. Usually, as circuit size increases, the percentage of don’t cares in the test set increases. As a result, test vector ordering for any arbitrary filling of don’t care bits is insufficient for producing effective reduction in switching activity during testing of large circuits. Since don’t cares dominate the test sets for larger circuits, don’t care filling plays a crucial role in reducing switching activity during testing. Taking this into consideration, we propose an algorithm, XStat, which is capable of performing test vector ordering while preserving don’t care bits in the test vectors, following which, the don’t cares are filled in an intelligent fashion for minimizing input switching activity, which effectively minimizes switching activity inside the circuit (Girard et al., 1998). Through empirical validation on benchmark circuits, we show that XStat minimizes peak switching activity significantly, during testing. Although XStat is a very powerful heuristic for minimizing peak input-switchingactivity, it will not guarantee optimality. To address this issue, we propose an algorithm that uses Dynamic Programming to calculate the lower bound for a given sequence of test vectors, and subsequently uses a greedy strategy for filling don’t cares in this sequence to achieve this lower bound, thereby guaranteeing optimality. This algorithm, which we refer to as DP-fill in this thesis, provides the globally optimal solution for minimizing peak input-switching-activity and also is the best known in the literature for minimizing peak input-switching-activity during testing. The proof of optimality of DP-fill in minimizing peak input-switching-activity is also provided in this thesis

Test and Diagnosis of Integrated Circuits

The ever-increasing growth of the semiconductor market results in an increasing complexity of digital circuits. Smaller, faster, cheaper and low-power consumption are the main challenges in semiconductor industry. The reduction of transistor size and the latest packaging technology (i.e., System-On-a-Chip, System-In-Package, Trough Silicon Via 3D Integrated Circuits) allows the semiconductor industry to satisfy the latest challenges. Although producing such advanced circuits can benefit users, the manufacturing process is becoming finer and denser, making chips more prone to defects.The work presented in the HDR manuscript addresses the challenges of test and diagnosis of integrated circuits. It covers:- Power aware test;- Test of Low Power Devices;- Fault Diagnosis of digital circuits

Design-for-delay-testability techniques for high-speed digital circuits

The importance of delay faults is enhanced by the ever increasing clock rates and decreasing geometry sizes of nowadays' circuits. This thesis focuses on the development of Design-for-Delay-Testability (DfDT) techniques for high-speed circuits and embedded cores. The rising costs of IC testing and in particular the costs of Automatic Test Equipment are major concerns for the semiconductor industry. To reverse the trend of rising testing costs, DfDT is\ud getting more and more important

Improved Path Recovery in Pseudo Functional Path Delay Test Using Extended Value Algebra

Scan-based delay test achieves high fault coverage due to its improved controllability and observability. This is particularly important for our K Longest Paths Per Gate (KLPG) test approach, which has additional necessary assignments on the paths. At the same time, some percentage of the flip-flops in the circuit will not scan, increasing the difficulty in test generation. In particular, there is no direct control on the outputs of those non-scan cells. All the non-scan cells that cannot be initialized are considered “uncontrollable” in the test generation process. They behave like “black boxes” and, thus, may block a potential path propagation, resulting in path delay test coverage loss. It is common for the timing critical paths in a circuit to pass through nodes influenced by the non-scan cells. In our work, we have extended the traditional Boolean algebra by including the “uncontrolled” state as a legal logic state, so that we can improve path coverage. Many path pruning decisions can be taken much earlier and many of the lost paths due to uncontrollable non-scan cells can be recovered, increasing path coverage and potentially reducing average CPU time per path. We have extended the existing traditional algebra to an 11-value algebra: Zero (stable), One (stable), Unknown, Uncontrollable, Rise, Fall, Zero/Uncontrollable, One/Uncontrollable, Unknown/Uncontrollable, Rise/Uncontrollable, and Fall/Uncontrollable. The logic descriptions for the NOT, AND, NAND, OR, NOR, XOR, XNOR, PI, Buff, Mux, TSL, TSH, TSLI, TSHI, TIE1 and TIE0 cells in the ISCAS89 benchmark circuits have been extended to the 11-value truth table. With 10% non-scan flip-flops, improved path delay fault coverage has been observed in comparison to that with the traditional algebra. The greater the number of long paths we want to test; the greater the path recovery advantage we achieve using our algebra. Along with improved path recovery, we have been able to test a greater number of transition fault sites. In most cases, the average CPU time per path is also lower while using the 11-value algebra. The number of tested paths increased by an average of 1.9x for robust tests, and 2.2x for non-robust tests, for K=5 (five longest rising and five longest falling transition paths through each line in the circuit), using the eleven-value algebra in contrast to the traditional algebra. The transition fault coverage increased by an average of 70%. The improvement increased with higher K values. The CPU time using the extended algebra increased by an average of 20%. So the CPU time per path decreased by an average of 40%. In future work, the extended algebra can achieve better test coverage for memory intensive circuits, circuits with logic black boxes, third party IPs, and analog units

Interconnect yield analysis and fault tolerance for field programmable gate arrays

Imperial Users onl

Modelling and Test Generation for Crosstalk Faults in DSM Chips

In the era of deep submicron technology (DSM), many System-on-Chip (SoC) applications require the components to be operating at high clock speeds. With the shrinking feature size and ever increasing clock frequencies, the DSM technology has led to a well-known problem of Signal Integrity (SI) more especially in the connecting layout design. The increasing aspect ratios of metal wires and also the ratio of coupling capacitance over substrate capacitance result in electrical coupling of interconnects which leads to crosstalk problems. In this thesis, first the work carried out to model the crosstalk behaviour between aggressor and victim by considering the distributed RLGC parameters of interconnect and the coupling capacitance and mutual conductance between the two nets is presented. The proposed model also considers the RC linear models of the CMOS drivers and receivers. The behaviour of crosstalk in case of under etching problem has been studied and modelled by distributing and approximating the defect behaviour throughout the nets. Next, the proposed model has also been extended to model the behaviour of crosstalk in case of one victim is influenced by several aggressors by considering all aggressors have similar effect (worst-case) on victim. In all the above cases simulation experiments were also carried out and compared with well-known circuit simulation tool PSPICE. It has been proved that the generated crosstalk model is faster and the results generated are within 10% of error margin compared to latter simulation tool. Because of the accuracy and speed of the proposed model, the model is very useful for both SoC designers and test engineers to analyse the crosstalk behaviour. Each manufactured device needs to be tested thoroughly to ensure the functionality before its delivery. The test pattern generation for crosstalk faults is also necessary to test the corresponding crosstalk faults. In this thesis, the well-known PODEM algorithm for stuck-at faults is extended to generate the test patterns for crosstalk faults between single aggressor and single victim. To apply modified PODEM for crosstalk faults, the transition behaviour has been divided into two logic parts as before transition and after transition. After finding individually required test patterns for before transition and after transition, the generated logic vectors are appended to create transition test patterns for crosstalk faults. The developed algorithm is also applied for a few ISCAS 85 benchmark circuits and the fault coverage is found excellent in most circuits. With the incorporation of proposed algorithm into the ATPG tools, the efficiency of testing will be improved by generating the test patterns for crosstalk faults besides for the conventional stuck-at faults. In generating test patterns for crosstalk faults on single victim due to multiple aggressors, the modified PODEM algorithm is found to be more time consuming. The search capability of Genetic Algorithms in finding the required combination of several input factors for any optimized problem fascinated to apply GA for generating test patterns as generating the test pattern is also similar to finding the required vector out of several input transitions. Initially the GA is applied for generating test patterns for stuck-at faults and compared the results with PODEM algorithm. As the fault coverage is almost similar to the deterministic algorithm PODEM, the GA developed for stuck-at faults is extended to find test patterns for crosstalk faults between single aggressor and single victim. The elitist GA is also applied for a few ISCAS 85 benchmark circuits. Later the algorithm is extended to generate test patterns for worst-case crosstalk faults. It has been proved that elitist GA developed in this thesis is also very useful in generating test patterns for crosstalk faults especially for multiple aggressor and single victim crosstalk faults

Conception et test des circuits et systèmes numériques à haute fiabilité et sécurité

Research activities I carried on after my nomination as Chargé de Recherche deal with the definition of methodologies and tools for the design, the test and the reliability of secure digital circuits and trustworthy manufacturing. More recently, we have started a new research activity on the test of 3D stacked Integrated CIrcuits, based on the use of Through Silicon Vias. Moreover, thanks to the relationships I have maintained after my post-doc in Italy, I have kept on cooperating with Politecnico di Torino on the topics related to test and reliability of memories and microprocessors.Secure and Trusted DevicesSecurity is a critical part of information and communication technologies and it is the necessary basis for obtaining confidentiality, authentication, and integrity of data. The importance of security is confirmed by the extremely high growth of the smart-card market in the last 20 years. It is reported in "Le monde Informatique" in the article "Computer Crime and Security Survey" in 2007 that financial losses due to attacks on "secure objects" in the digital world are greater than $11 Billions. Since the race among developers of these secure devices and attackers accelerates, also due to the heterogeneity of new systems and their number, the improvement of the resistance of such components becomes today’s major challenge.Concerning all the possible security threats, the vulnerability of electronic devices that implement cryptography functions (including smart cards, electronic passports) has become the Achille’s heel in the last decade. Indeed, even though recent crypto-algorithms have been proven resistant to cryptanalysis, certain fraudulent manipulations on the hardware implementing such algorithms can allow extracting confidential information. So-called Side-Channel Attacks have been the first type of attacks that target the physical device. They are based on information gathered from the physical implementation of a cryptosystem. For instance, by correlating the power consumed and the data manipulated by the device, it is possible to discover the secret encryption key. Nevertheless, this point is widely addressed and integrated circuit (IC) manufacturers have already developed different kinds of countermeasures.More recently, new threats have menaced secure devices and the security of the manufacturing process. A first issue is the trustworthiness of the manufacturing process. From one side, secure devices must assure a very high production quality in order not to leak confidential information due to a malfunctioning of the device. Therefore, possible defects due to manufacturing imperfections must be detected. This requires high-quality test procedures that rely on the use of test features that increases the controllability and the observability of inner points of the circuit. Unfortunately, this is harmful from a security point of view, and therefore the access to these test features must be protected from unauthorized users. Another harm is related to the possibility for an untrusted manufacturer to do malicious alterations to the design (for instance to bypass or to disable the security fence of the system). Nowadays, many steps of the production cycle of a circuit are outsourced. For economic reasons, the manufacturing process is often carried out by foundries located in foreign countries. The threat brought by so-called Hardware Trojan Horses, which was long considered theoretical, begins to materialize.A second issue is the hazard of faults that can appear during the circuit’s lifetime and that may affect the circuit behavior by way of soft errors or deliberate manipulations, called Fault Attacks. They can be based on the intentional modification of the circuit’s environment (e.g., applying extreme temperature, exposing the IC to radiation, X-rays, ultra-violet or visible light, or tampering with clock frequency) in such a way that the function implemented by the device generates an erroneous result. The attacker can discover secret information by comparing the erroneous result with the correct one. In-the-field detection of any failing behavior is therefore of prime interest for taking further action, such as discontinuing operation or triggering an alarm. In addition, today’s smart cards use 90nm technology and according to the various suppliers of chip, 65nm technology will be effective on the horizon 2013-2014. Since the energy required to force a transistor to switch is reduced for these new technologies, next-generation secure systems will become even more sensitive to various classes of fault attacks.Based on these considerations, within the group I work with, we have proposed new methods, architectures and tools to solve the following problems:• Test of secure devices: unfortunately, classical techniques for digital circuit testing cannot be easily used in this context. Indeed, classical testing solutions are based on the use of Design-For-Testability techniques that add hardware components to the circuit, aiming to provide full controllability and observability of internal states. Because crypto‐ processors and others cores in a secure system must pass through high‐quality test procedures to ensure that data are correctly processed, testing of crypto chips faces a dilemma. In fact design‐for‐testability schemes want to provide high controllability and observability of the device while security wants minimal controllability and observability in order to hide the secret. We have therefore proposed, form one side, the use of enhanced scan-based test techniques that exploit compaction schemes to reduce the observability of internal information while preserving the high level of testability. From the other side, we have proposed the use of Built-In Self-Test for such devices in order to avoid scan chain based test.• Reliability of secure devices: we proposed an on-line self-test architecture for hardware implementation of the Advanced Encryption Standard (AES). The solution exploits the inherent spatial replications of a parallel architecture for implementing functional redundancy at low cost.• Fault Attacks: one of the most powerful types of attack for secure devices is based on the intentional injection of faults (for instance by using a laser beam) into the system while an encryption occurs. By comparing the outputs of the circuits with and without the injection of the fault, it is possible to identify the secret key. To face this problem we have analyzed how to use error detection and correction codes as counter measure against this type of attack, and we have proposed a new code-based architecture. Moreover, we have proposed a bulk built-in current-sensor that allows detecting the presence of undesired current in the substrate of the CMOS device.• Fault simulation: to evaluate the effectiveness of countermeasures against fault attacks, we developed an open source fault simulator able to perform fault simulation for the most classical fault models as well as user-defined electrical level fault models, to accurately model the effect of laser injections on CMOS circuits.• Side-Channel attacks: they exploit physical data-related information leaking from the device (e.g. current consumption or electro-magnetic emission). One of the most intensively studied attacks is the Differential Power Analysis (DPA) that relies on the observation of the chip power fluctuations during data processing. I studied this type of attack in order to evaluate the influence of the countermeasures against fault attack on the power consumption of the device. Indeed, the introduction of countermeasures for one type of attack could lead to the insertion of some circuitry whose power consumption is related to the secret key, thus allowing another type of attack more easily. We have developed a flexible integrated simulation-based environment that allows validating a digital circuit when the device is attacked by means of this attack. All architectures we designed have been validated through this tool. Moreover, we developed a methodology that allows to drastically reduce the time required to validate countermeasures against this type of attack.TSV- based 3D Stacked Integrated Circuits TestThe stacking process of integrated circuits using TSVs (Through Silicon Via) is a promising technology that keeps the development of the integration more than Moore’s law, where TSVs enable to tightly integrate various dies in a 3D fashion. Nevertheless, 3D integrated circuits present many test challenges including the test at different levels of the 3D fabrication process: pre-, mid-, and post- bond tests. Pre-bond test targets the individual dies at wafer level, by testing not only classical logic (digital logic, IOs, RAM, etc) but also unbounded TSVs. Mid-bond test targets the test of partially assembled 3D stacks, whereas finally post-bond test targets the final circuit.The activities carried out within this topic cover 2 main issues:• Pre-bond test of TSVs: the electrical model of a TSV buried within the substrate of a CMOS circuit is a capacitance connected to ground (when the substrate is connected to ground). The main assumption is that a defect may affect the value of that capacitance. By measuring the variation of the capacitance’s value it is possible to check whether the TSV is correctly fabricated or not. We have proposed a method to measure the value of the capacitance based on the charge/ discharge delay of the RC network containing the TSV.• Test infrastructures for 3D stacked Integrated Circuits: testing a die before stacking to another die introduces the problem of a dynamic test infrastructure, where test data must be routed to a specific die based on the reached fabrication step. New solutions are proposed in literature that allow reconfiguring the test paths within the circuit, based on on-the-fly requirements. We have started working on an extension of the IEEE P1687 test standard that makes use of an automatic die-detection based on pull-up resistors.Memory and Microprocessor Test and ReliabilityThanks to device shrinking and miniaturization of fabrication technology, performances of microprocessors and of memories have grown of more than 5 magnitude order in the last 30 years. With this technology trend, it is necessary to face new problems and challenges, such as reliability, transient errors, variability and aging.In the last five years I’ve worked in cooperation with the Testgroup of Politecnico di Torino (Italy) to propose a new method to on-line validate the correctness of the program execution of a microprocessor. The main idea is to monitor a small set of control signals of the processors in order to identify incorrect activation sequences. This approach can detect both permanent and transient errors of the internal logic of the processor.Concerning the test of memories, we have proposed a new approach to automatically generate test programs starting from a functional description of the possible faults in the memory.Moreover, we proposed a new methodology, based on microprocessor error probability profiling, that aims at estimating fault injection results without the need of a typical fault injection setup. The proposed methodology is based on two main ideas: a one-time fault-injection analysis of the microprocessor architecture to characterize the probability of successful execution of each of its instructions in presence of a soft-error, and a static and very fast analysis of the control and data flow of the target software application to compute its probability of success