Novel Ternary Logic Gates Design in Nanoelectronics

In this paper, standard ternary logic gates are initially designed to considerably reduce static power consumption. This study proposes novel ternary gates based on two supply voltages in which the direct current is eliminated and the leakage current is reduced considerably. In addition, ST-OR and ST-AND are generated directly instead of ST-NAND and ST-NOR. The proposed gates have a high noise margin near V_(DD)/4. The simulation results indicated that the power consumption and PDP underwent a~sharp decrease and noise margin showed a considerable increase in comparison to both one supply and two supply based designs in previous works. PDP is improved in the proposed OR, as compared to one supply and two supply based previous works about 83% and 63%, respectively. Also, a memory cell is designed using the proposed STI logic gate, which has a considerably lower static power to store logic ‘1’ and the static noise margin, as compared to other designs

An Optimal Gate Design for the Synthesis of Ternary Logic Circuits

Department of Electrical EngineeringOver the last few decades, CMOS-based digital circuits have been steadily developed. However, because of the power density limits, device scaling may soon come to an end, and new approaches for circuit designs are required. Multi-valued logic (MVL) is one of the new approaches, which increases the radix for computation to lower the complexity of the circuit. For the MVL implementation, ternary logic circuit designs have been proposed previously, though they could not show advantages over binary logic, because of unoptimized synthesis techniques. In this thesis, we propose a methodology to design ternary gates by modeling pull-up and pull-down operations of the gates. Our proposed methodology makes it possible to synthesize ternary gates with a minimum number of transistors. From HSPICE simulation results, our ternary designs show significant power-delay product reductions; 49 % in the ternary full adder and 62 % in the ternary multiplier compared to the existing methodology. We have also compared the number of transistors in CMOS-based binary logic circuits and ternary device-based logic circuits We propose a methodology for using ternary values effectively in sequential logic. Proposed ternary D flip-flop is designed to normally operate in four-edges of a ternary clock signal. A quad-edge-triggered ternary D flip-flop (QETDFF) is designed with static gates using CNTFET. From HSPICE simulation results, we have confirmed that power-delay-product (PDP) of QETDFF is reduced by 82.31 % compared to state of the art ternary D flip-flop. We synthesize a ternary serial adder using QETDFF. PDP of the proposed ternary serial adder is reduced by 98.23 % compared to state of the art design.ope

Digital Circuit Design Using Floating Gate Transistors

Floating gate (flash) transistors are used exclusively for memory applications today. These applications include SD cards of various form factors, USB flash drives and SSDs. In this thesis, we explore the use of flash transistors to implement digital logic circuits. Since the threshold voltage of flash transistors can be modified at a fine granularity during programming, several advantages are obtained by our flash-based digital circuit design approach. For one, speed binning at the factory can be controlled with precision. Secondly, an IC can be re-programmed in the field, to negate effects such as aging, which has been a significant problem in recent times, particularly for mission-critical applications. Thirdly, unlike a regular MOSFET, which has one threshold voltage level, a flash transistor can have multiple threshold voltage levels. The benefit of having multiple threshold voltage levels in a flash transistor is that it allows the ability to encode more symbols in each device, unlike a regular MOSFET. This allows us to implement multi-valued logic functions natively. In this thesis, we evaluate different flash-based digital circuit design approaches and compare their performance with a traditional CMOS standard cell-based design approach. We begin by evaluating our design approach at the cell level to optimize the design’s delay, power energy and physical area characteristics. The flash-based approach is demonstrated to be better than the CMOS standard cell approach, for these performance metrics. Afterwards, we present the performance of our design approach at the block level. We describe a synthesis flow to decompose a circuit block into a network of interconnected flash-based circuit cells. We also describe techniques to optimize the resulting network of flash-based circuit cells using don’t cares. Our optimization approach distinguishes itself from other optimization techniques that use don’t cares, since it a) targets a flash-based design flow, b) optimizes clusters of logic nodes at once instead of one node at a time, c) attempts to reduce the number of cubes instead of reducing the number of literals in each cube and d) performs optimization on the post-technology mapped netlist which results in a direct improvement in result quality, as compared to pre-technology mapping logic optimization that is typically done in the literature. The resulting network characteristics (delay, power, energy and physical area) are presented. These results are compared with a standard cell-based realization of the same block (obtained using commercial tools) and we demonstrate significant improvements in all the design metrics. We also study flash-based FPGA designs (both static and dynamic), and present the tradeoff of delay, power dissipation and energy consumption of the various designs. Our work differs from previously proposed flash-based FPGAs, since we embed the flash transistors (which store the configuration bits) directly within the logic and interconnect fabrics. We also present a detailed description of how the programming of the configuration bits is accomplished, for all the proposed designs

Digital Circuit Design Using Floating Gate Transistors

Floating gate (flash) transistors are used exclusively for memory applications today. These applications include SD cards of various form factors, USB flash drives and SSDs. In this thesis, we explore the use of flash transistors to implement digital logic circuits. Since the threshold voltage of flash transistors can be modified at a fine granularity during programming, several advantages are obtained by our flash-based digital circuit design approach. For one, speed binning at the factory can be controlled with precision. Secondly, an IC can be re-programmed in the field, to negate effects such as aging, which has been a significant problem in recent times, particularly for mission-critical applications. Thirdly, unlike a regular MOSFET, which has one threshold voltage level, a flash transistor can have multiple threshold voltage levels. The benefit of having multiple threshold voltage levels in a flash transistor is that it allows the ability to encode more symbols in each device, unlike a regular MOSFET. This allows us to implement multi-valued logic functions natively. In this thesis, we evaluate different flash-based digital circuit design approaches and compare their performance with a traditional CMOS standard cell-based design approach. We begin by evaluating our design approach at the cell level to optimize the design’s delay, power energy and physical area characteristics. The flash-based approach is demonstrated to be better than the CMOS standard cell approach, for these performance metrics. Afterwards, we present the performance of our design approach at the block level. We describe a synthesis flow to decompose a circuit block into a network of interconnected flash-based circuit cells. We also describe techniques to optimize the resulting network of flash-based circuit cells using don’t cares. Our optimization approach distinguishes itself from other optimization techniques that use don’t cares, since it a) targets a flash-based design flow, b) optimizes clusters of logic nodes at once instead of one node at a time, c) attempts to reduce the number of cubes instead of reducing the number of literals in each cube and d) performs optimization on the post-technology mapped netlist which results in a direct improvement in result quality, as compared to pre-technology mapping logic optimization that is typically done in the literature. The resulting network characteristics (delay, power, energy and physical area) are presented. These results are compared with a standard cell-based realization of the same block (obtained using commercial tools) and we demonstrate significant improvements in all the design metrics. We also study flash-based FPGA designs (both static and dynamic), and present the tradeoff of delay, power dissipation and energy consumption of the various designs. Our work differs from previously proposed flash-based FPGAs, since we embed the flash transistors (which store the configuration bits) directly within the logic and interconnect fabrics. We also present a detailed description of how the programming of the configuration bits is accomplished, for all the proposed designs

Synthesis of Control Elements from Petri Net Models

Methods are presented for synthesizing delay-insensitive circuits whose behavior is specified by Petri net models of macromodular control elements. These control elements implement five natural functions used in asynchronous system design. Particular attention is paid to modules requiring mutual exclusion where metastability must be carefully controlled

High-Performance Ternary (4:2) Compressor Based on Capacitive Threshold Logic

This paper presents a ternary (4:2) compressor, which is an important component in multiplication. However, the structure differs from the binary counterpart since the ternary model does not require carry signals. The method of capacitive threshold logic (CTL) is used to achieve the output signals directly. Unlike the previously presented similar structure, the entire capacitor network is divided into two parts. This segregation results in higher reliability and robustness against unwanted process, voltage, and temperature (PVT) variations. Simulations are performed by HSPICE and 32nm CNFET technology. Simulation results demonstrate about 94% higher performance in terms of power-delay product (PDP) for the new design over the previous one