A General Framework for Analyzing, Characterizing, and Implementing Spectrally Modulated, Spectrally Encoded Signals

Fourth generation (4G) communications will support many capabilities while providing universal, high speed access. One potential enabler for these capabilities is software defined radio (SDR). When controlled by cognitive radio (CR) principles, the required waveform diversity is achieved via a synergistic union called CR-based SDR. Research is rapidly progressing in SDR hardware and software venues, but current CR-based SDR research lacks the theoretical foundation and analytic framework to permit efficient implementation. This limitation is addressed here by introducing a general framework for analyzing, characterizing, and implementing spectrally modulated, spectrally encoded (SMSE) signals within CR-based SDR architectures. Given orthogonal frequency division multiplexing (OFDM) is a 4G candidate signal, OFDM-based signals are collectively classified as SMSE since modulation and encoding are spectrally applied. The proposed framework provides analytic commonality and unification of SMSE signals. Applicability is first shown for candidate 4G signals, and resultant analytic expressions agree with published results. Implementability is then demonstrated in multiple coexistence scenarios via modeling and simulation to reinforce practical utility

Cyclic redundancy check-based detection algorithms for automatic identification system signals received by satellite.

This paper addresses the problem of demodulating signals transmitted in the automatic identification system. The main characteristics of such signals consist of two points: (i) they are modulated using a trellis-coded modulation, more precisely a Gaussian minimum shift keying modulation; and (ii) they are submitted to a bit stuffing procedure, which makes more difficult the detection of the transmitted information bits. This paper presents several demodulation algorithms developed in different contexts: mono-user and multi-user transmissions, and known/unknown phase shift. The proposed receiver uses the cyclic redundancy check (CRC) present in the automatic identification system signals for error correction and not for error detection only. By using this CRC, a particular Viterbi algorithm, on the basis of a so-called extended trellis, is developed. This trellis is defined by extended states composed of a trellis code state and a CRC state. Moreover, specific conditional transitions are defined to take into account the possible presence of stuffing bits. The algorithms proposed in the multi-user scenario present a small increase of computation complexity with respect to the mono-user algorithms. Some performance results are presented for several scenarios in the context of the automatic identification system and compared with those of existing techniques developed in similar scenarios

System Architecture for Low-Power Ubiquitously Connected Remote Health Monitoring Applications With Smart Transmission Mechanism

We present a novel smart transmission technique with seamless handoff mechanism to achieve ubiquitous connectivity using multiple on-chip radios targeting remote health monitoring applications. For the first time to the best of our knowledge, a system architecture for low-power ubiquitously connected multiparametric remote health monitoring system is proposed in this paper. The architecture proposed uses a generic adaptive rule engine for classifying the collected multiparametric data from patient and smartly transmit the data when only needed. The on-chip seamless handoff mechanism proposed aids for the ubiquitous connectivity with a very good energy savings by intelligent controlling of the multiple on-chip radios. The performance analysis of the proposed on-chip seamless handoff mechanism along with adaptive rule engine-based smart transmission mechanism achieves on an average of 50.39% of energy saving and 51.01% reduction in duty cycle of transmitter taken over 20 users compared with the continuous transmission. From the hardware complexity analysis made on the proposed seamless handoff controller and adaptive rule engine concludes that they require only 2082 CMOS transistors for real-time implementation

Technologies to improve the performance of wireless sensor networks in high-traffic applications

The expansion of wireless sensor networks to advanced areas, including structure health monitoring, multimedia surveillance, and health care monitoring applications, has resulted in new and complex problems. Traditional sensor systems are designed and optimised for extremely low traffic loads. However, it has been witnessed that network performance drops rapidly with the higher traffic loads common in advanced applications. In this thesis, we examine the system characteristics and new system requirements of these advanced sensor network applications. Based on this analysis, we propose an improved architecture for wireless sensor systems to increase the network performance while maintaining compatibility with the essential WSN requirements: low power, low cost, and distributed scalability. We propose a modified architecture deriving from the IEEE 802.15.4 standard, which is shown to significantly increase the network performance in applications generating increased data loads. This is achieved by introducing the possibility of independently allocating the sub-carriers in a distributed manner. As a result, the overall efficiency of the channel contention mechanism will be increased to deliver higher throughput with lower energy consumption. Additionally, we develop the concept of increasing the data transmission efficiency by adapting the spreading code length to the wireless environment. Such a modification will not only be able to deliver higher throughput but also maintain a reliable wireless link in the harsh RF environment. Finally, we propose the use of the battery recovery effect to increase the power efficiency of the system under heavy traffic load conditions. These three innovations minimise the contention window period while maximising the capacity of the available channel, which is shown to increase network performance in terms of energy efficiency, throughput and latency. The proposed system is shown to be backwards compatible and able to satisfy both traditional and advanced applications and is particularly suitable for deployment in harsh RF environments. Experiments and analytic techniques have been described and developed to produce performance metrics for all the proposed techniques