Interference Mitigation in Wireless Communications

The primary objective of this thesis is to design advanced interference resilient schemes for asynchronous slow frequency hopping wireless personal area networks (FH-WPAN) and time division multiple access (TDMA) cellular systems in interference dominant environments. We also propose an interference-resilient power allocation method for multiple-input-multiple-output (MIMO) systems. For asynchronous FH-WPANs in the presence of frequent packet collisions, we propose a single antenna interference canceling dual decision feedback (IC-DDF) receiver based on joint maximum likelihood (ML) detection and recursive least squares (RLS) channel estimation. For the system level performance evaluation, we propose a novel geometric method that combines bit error rate (BER) and the spatial distribution of the traffic load of CCI for the computation of packet error rate (PER). We also derived the probabilities of packet collision in multiple asynchronous FH-WPANs with uniform and nonuniform traffic patterns. For the design of TDMA receivers resilient to CCI in frequency selective channels, we propose a soft output joint detection interference rejection combining delayed decision feedback sequence estimation (JD IRC-DDFSE) scheme. In the proposed scheme, IRC suppresses the CCI, while DDFSE equalizes ISI with reduced complexity. Also, the soft outputs are generated from IRC-DDFSE decision metric to improve the performance of iterative or non-iterative type soft-input outer code decoders. For the design of interference resilient power allocation scheme in MIMO systems, we investigate an adaptive power allocation method using subset antenna transmission (SAT) techniques. Motivated by the observation of capacity imbalance among the multiple parallel sub-channels, the SAT method achieves high spectral efficiency by allocating power on a selected transmit antenna subset. For 4 x 4 V-BLAST MIMO systems, the proposed scheme with SAT showed analogous results. Adaptive modulation schemes combined with the proposed method increase the capacity gains. From a feasibility viewpoint, the proposed method is a practical solution to CCI-limited MIMO systems since it does not require the channel state information (CSI) of CCI.Ph.D.Committee Chair: Professor Gordon L. StBe

Enabling Technology and Algorithm Design for Location-Aware Communications

Location-awareness is emerging as a promising technique for future-generation wire­ less network to adaptively enhance and optimize its overall performance through location-enabled technologies such as location-assisted transceiver reconfiguration and routing. The availability of accurate location information of mobile users becomes the essential prerequisite for the design of such location-aware networks. Motivated by the low locationing accuracy of the Global Positioning System (GPS) in dense multipath environments, which is commonly used for acquiring location information in most of the existing wireless networks, wireless communication system-based po­sitioning systems have been investigated as alternatives to fill the gap of the GPS in coverage. Distance-based location techniques using time-of-arrival (TOA) mea­surements are commonly preferred by broadband wireless communications where the arrival time of the signal component of the First Arriving Path (FAP) can be con­verted to the distance between the receiver and the transmitter with known location. With at least three transmitters, the location of the receiver can be determined via trilatération method. However, identification of the FAP’s signal component in dense multipath scenarios is quite challenging due to the significantly weaker power of the FAP as compared with the Later Arriving Paths (LAPs) from scattering, reflection and refraction, and the superposition of these random arrival LAPs’ signal compo­ nents will become large interference to detect the FAP. In this thesis, a robust FAP detection scheme based on multipath interference cancellation is proposed to im­ prove the accuracy of location estimation in dense multipath environments. In the proposed algorithm, the signal components of LAPs is reconstructed based on the estimated channel and data with the assist of the communication receiver, and sub­ sequently removed from the received signal. Accurate FAP detection results are then achieved with the cross-correlation between the interference-suppressed signal and an augmented preamble which is the combination of the original preamble for com­ munications and the demodulated data sequences. Therefore, more precise distance estimation (hence location estimation) can be obtained with the proposed algorithm for further reliable network optimization strategy design. On the other hand, multiceli cooperative communication is another emerging technique to substantially improve the coverage and throughput of traditional cellular networks. Location-awareness also plays an important role in the design and imple­mentation of multiceli cooperation technique. With accurate location information of mobile users, the complexity of multiceli cooperation algorithm design can be dra­matically reduced by location-assisted applications, e.g., automatic cooperative base station (BS) determination and signal synchronization. Therefore, potential latency aroused by cooperative processing will be minimized. Furthermore, the cooperative BSs require the sharing of certain information, e.g., channel state information (CSI), user data and transmission parameters to perform coordination in their signaling strategies. The BSs need to have the capabilities to exchange available information with each other to follow up with the time-varying communication environment. As most of broadband wireless communication systems are already orthogonal frequency division multiplexing (OFDM)-based, a Multi-Layered OFDM System, which is spe­cially tailored for multiceli cooperation is investigated to provide parallel robust, efficient and flexible signaling links for BS coordination purposes. These layers are overlaid with data-carrying OFDM signals in both time and frequency domains and therefore, no dedicated radio resources are required for multiceli cooperative networks. In the final aspect of this thesis, an enhanced channel estimation through itera­ tive decision-directed method is investigated for OFDM system, which aims to provide more accurate estimation results with the aid of the demodulated OFDM data. The performance of traditional training sequence-based channel estimation is often lim­ ited by the length of the training. To achieve acceptable estimation performance, a long sequence has to be used which dramatically reduces the transmission efficiency of data communication. In this proposed method, the restriction of the training se­quence length can be removed and high channel estimation accuracy can be achieved with high transmission efficiency, and therefore it particular fits in multiceli coopera­tive networks. On the other hand, as the performance of the proposed FAP detection scheme also relies on the accuracy of channel estimation and data detection results, the proposed method can be combined with the FAP detection scheme to further optimize the accuracy of multipath interference cancellation and FAP detection

Joint signal detection and channel estimation in rank-deficient MIMO systems

L'évolution de la prospère famille des standards 802.11 a encouragé le développement des technologies appliquées aux réseaux locaux sans fil (WLANs). Pour faire face à la toujours croissante nécessité de rendre possible les communications à très haut débit, les systèmes à antennes multiples (MIMO) sont une solution viable. Ils ont l'avantage d'accroître le débit de transmission sans avoir recours à plus de puissance ou de largeur de bande. Cependant, l'industrie hésite encore à augmenter le nombre d'antennes des portables et des accésoires sans fil. De plus, à l'intérieur des bâtiments, la déficience de rang de la matrice de canal peut se produire dû à la nature de la dispersion des parcours de propagation, ce phénomène est aussi occasionné à l'extérieur par de longues distances de transmission. Ce projet est motivé par les raisons décrites antérieurement, il se veut un étude sur la viabilité des transcepteurs sans fil à large bande capables de régulariser la déficience de rang du canal sans fil. On vise le développement des techniques capables de séparer M signaux co-canal, même avec une seule antenne et à faire une estimation précise du canal. Les solutions décrites dans ce document cherchent à surmonter les difficultés posées par le medium aux transcepteurs sans fil à large bande. Le résultat de cette étude est un algorithme transcepteur approprié aux systèmes MIMO à rang déficient

An investigation of a frequency diverse array

This thesis presents a novel concept for focusing an antenna beam pattern as a function of range, time, and angle. In conventional phased arrays, beam steering is achieved by applying a linear phase progression across the aperture. This thesis shows that by applying an additional linear frequency shift across the elements, a new term is generated which results in a scan angle that varies with range in the far-field. Moreover, the antenna pattern is shown to scan in range and angle as a function of time. These properties result in more flexible beam scan options for phased array antennas than traditional phase shifter implementations. The thesis subsequently goes on to investigate this phenomenon via full scale experimentation, and explores a number of aspects of applying frequency diversity spatially across array antennas. This new form of frequency diverse array may have applications to multipath mitigation, where a radio signal takes two or more routes between the transmitter and receiver due to scattering from natural and man-made objects. Since the interfering signals arrive from more than one direction, the range-dependent and auto-scanning properties of the frequency diverse array beam may be useful to isolate and suppress the interference. The frequency diverse array may also have applications to wideband array steering, in lieu of true time delay solutions which are often used to compensate for linear phase progression with frequency across an array, and to sonar, where the speed of propagation results in large percentage bandwidth, creating similar wideband array effects. The frequency diverse array is also a stepping stone to more sophisticated joint antenna and waveform design for the creation of new radar modes, such as simultaneous multi-mode operation, for example, enabling joint synthetic aperture radar and ground moving target indication

Beamforming for OFDM based hybrid terrestrial satellite mobile system

EThOS - Electronic Theses Online ServiceGBUnited Kingdo

Multiantenna Interference Mitigation Schemes and Resource Allocation for Cognitive Radio

Maximum and efficient utilization of available resources has been a central theme of research on various areas of science and engineering. Wireless communication is not an exception to this. With the rapid growth of wireless communication applications, radio frequency spectrum has become a valuable commodity. Supporting very high demands for data rate and throughput has become a challenging problem which requires innovative solutions. Dynamic spectrum sharing (DSS) based cognitive radio (CR) is envisioned as a promising technology for future wireless communication systems, such as fifth generation (5G) further development and sixth generation (6G). Extensive research has been done in the areas of CRs and it is considered to mitigate the spectral crowding problem by introducing the notion of opportunistic spectrum usage. Spectrum sensing, which enables CRs to identify spectral holes, is a critical component in CR technology. Furthermore, improving the efficiency of the radio spectrum use through spectrum sensing and dynamic spectrum access (DSA) is one of the emerging trends. In the first part of this thesis, we focus on enhancing the spectrum usage of CR’s using interference cancellation methods that provides considerable performance gains with realistic computational complexity, especially, in the context of the widely used multicarrier waveforms. The primary focus is on interference rejection combining (IRC) methods, applied to the black-space cognitive radio (BS-CR). Earlier studies on the BS-CR in the literature were focused on using CRs as repeaters for the primary transmitter to guarantee that the CR is not causing significant interference to nearby primary users’ receivers. This kind of approaches are transmitter-centric in nature. In this thesis, receiver-centric approaches such as multi-antenna diversity combining, especially enhanced IRC methods, are considered and evaluated. IRC methods have been widely studied and adopted in several practical wireless communication systems. We focus on developing such BS-CR schemes under strong interference conditions, which has not been studied in the CR literature so far. Spatial covariance matrix estimation under mobility and high carrier frequencies is found to be the most critical part of such scheme. Algorithms and methods to mitigate these effects are developed in this thesis and they are evaluated under realistic BS-CR receiver operating conditions. We use sample covariance estimation approach with silent gaps in the CR transmisison. Covariance interpolation between silent gaps improves greatly the robustness with time-varying channels. Good link performance can be reached with low mobility at carrier frequency considered for the TV white-spaced case. The proposed BS-CR scheme could be feasible at below 6 GHz frequencies with pedestrian mobilities. The second part of this thesis investigates the effect of radio frequency (RF) impairments on the performance of the cognitive wireless communication. There are various unavoidable imperfections, mainly due to the limitations of analog high-frequency transmitter and receiver circuits. These imperfections include power amplifier (PA) non-linearities, receiver nonlinearities, and carrier frequency offset (CFO), which are considered in this study. These effects lead to significant signal distortion and, as a result of this, the wireless link quality may deteriorate. In multicarrier communications such signal distortions may lead to additional interference, and it is important to evaluate their effects on spectrum sensing quality and on the performance of the proposed BS-CR scheme. This part of the thesis provides critical analysis and insights into such issues caused by RF imperfections and demonstrates the need for designing proper compensation techniques required to avoid/reduce such degradations. It is found that the transmitter’s PA nonlinearities affect in the same way as in basic OFDM systems and BS-CR receiver’s linearity requirements are similar to those for advanced DSP-intensive software defined radios. The CR receiver’s CFO with respect to the PU has the most critical effect. However, synchronizing the CR with the needed high accuracy is considered achievable due to the PU signal’s high-power level. The final part of the thesis briefly looks at alternate waveforms and techniques that can be used in CRs. The filter bank multicarrier (FBMC) waveforms are considered as an alternative to the widely used OFDM schemes. Here the core idea is interference avoidance, targeting to reduce the interference leakage between CRs and the primary systems, by means of using a waveform with good spectrum localization properties. FBMC system’s performance is compared with OFDM based system in the context of CRs. The performance is compared from a combined spectrum sensing and resource allocation point of view through simulations. It is found that well-localized CR waveforms improve the CR link capacity, but with poorly localized primary signals, these possibilities are rather limited

D 3. 3 Final performance results and consolidated view on the most promising multi -node/multi -antenna transmission technologies

This document provides the most recent updates on the technical contributions and research challenges focused in WP3. Each Technology Component (TeC) has been evaluated under possible uniform assessment framework of WP3 which is based on the simulation guidelines of WP6. The performance assessment is supported by the simulation results which are in their mature and stable state. An update on the Most Promising Technology Approaches (MPTAs) and their associated TeCs is the main focus of this document. Based on the input of all the TeCs in WP3, a consolidated view of WP3 on the role of multinode/multi-antenna transmission technologies in 5G systems has also been provided. This consolidated view is further supported in this document by the presentation of the impact of MPTAs on METIS scenarios and the addressed METIS goals.Aziz, D.; Baracca, P.; De Carvalho, E.; Fantini, R.; Rajatheva, N.; Popovski, P.; Sørensen, JH.... (2015). D 3. 3 Final performance results and consolidated view on the most promising multi -node/multi -antenna transmission technologies. http://hdl.handle.net/10251/7675

Busy burst technology applied to OFDMA–TDD systems

The most significant bottleneck in wireless communication systems is an ever-increasing disproportion between the bandwidth demand and the available spectrum. A major challenge in the field of wireless communications is to maximise the spatial reuse of resources whilst avoiding detrimental co-channel interference (CCI). To this end, frequency planning and centralised coordination approaches are widely used in wireless networks. However, the networks for the next generation of wireless communications are often envisioned to be decentralised, randomly distributed in space, hierarchical and support heterogeneous traffic and service types. Fixed frequency allocation would not cater for the heterogeneous demands and centralised resource allocation would be cumbersome and require a lot of signalling. Decentralised radio resource allocation based on locally available information is considered the key. In this context, the busy burst (BB) signalling concept is identified as a potential mechanism for decentralised interference management in future generation networks. Interference aware allocation of time-frequency slots (chunks) is accomplished by letting receivers transmit a BB in a time-multiplexed mini-slot, upon successful reception of data. Exploiting channel reciprocity of the time division duplex (TDD) mode, the transmitters avoid reusing the chunks where the received BB power is above a pre-determined threshold so as to limit the CCI caused towards the reserved chunks to a threshold value. In this thesis, the performance of BB signalling mechanism in orthogonal frequency division multiple access - time division duplexing (OFDMA-TDD) systems is evaluated by means of system level simulations in networks operating in ad hoc and cellular scenarios. Comparisons are made against the state-of-the-art centralised CCI avoidance and mitigation methods, viz. frequency planning, fractional frequency reuse, and antenna array with switched grid of beams, as well as decentralised methods such as the carrier sense multiple access method that attempt to avoid CCI by avoiding transmission on chunks deemed busy. The results demonstrate that with an appropriate choice of threshold parameter, BB-based techniques outperform all of the above state-of-the-art methods. Moreover, it is demonstrated that by adjusting the BB-specific threshold parameter, the system throughput can be traded off for improving throughput for links with worse channel condition, both in the ad hoc and cellular scenario. Moreover, by utilising a variable BB power that allows a receiver to signal the maximum CCI it can tolerate, it is shown that a more favourable trade-off between total system throughput and link throughput can be made. Furthermore, by performing link adaptation, it is demonstrated that the spatial reuse and the energy efficiency can be traded off by adjusting the threshold parameter. Although the BB signalling mechanism is shown to be effective in avoiding detrimental CCI, it cannot mitigate CCI by itself. On the other hand, multiple antenna techniques such as adaptive beamforming or switched beam approaches allow CCI to be mitigated but suffer from hidden node problems. The final contribution of this thesis is that by combining the BB signalling mechanism with multiple antenna techniques, it is demonstrated that the hybrid approach enhances spatial reusability of resources whilst avoiding detrimental CCI. In summary, this thesis has demonstrated that BB provides a flexible radio resource mechanism that is suitable for future generation networks

MIMO Systems

In recent years, it was realized that the MIMO communication systems seems to be inevitable in accelerated evolution of high data rates applications due to their potential to dramatically increase the spectral efficiency and simultaneously sending individual information to the corresponding users in wireless systems. This book, intends to provide highlights of the current research topics in the field of MIMO system, to offer a snapshot of the recent advances and major issues faced today by the researchers in the MIMO related areas. The book is written by specialists working in universities and research centers all over the world to cover the fundamental principles and main advanced topics on high data rates wireless communications systems over MIMO channels. Moreover, the book has the advantage of providing a collection of applications that are completely independent and self-contained; thus, the interested reader can choose any chapter and skip to another without losing continuity