Phase Locking Authentication for Scan Architecture

Scan design is a widely used Design for Testability (DfT) approach for digital circuits. It provides a high level of controllability and observability resulting in a high fault coverage. To achieve a high level of testability, scan architecture must provide access to the internal nodes of the circuit-under-test (CUT). This access however leads to vulnerability in the security of the CUT. If an unrestricted access is provided through a scan architecture, unlimited test vectors can be applied to the CUT and its responses can be captured. Such an unrestricted access to the CUT can potentially undermine the security of the critical information stored in the CUT. There is a need to secure scan architecture to prevent hardware attacks however a secure solution may limit the CUT testability. There is a trade-off between security and testability, therefore, a secure scan architecture without hindering its controllability and observability is required. Three solutions to secure scan architecture have been proposed in this thesis. In the first method, the tester is authenticated and the number of authentication attempts has been limited. In the second method, a Phase Locked Loop (PLL) is utilized to secure scan architecture. In the third method, the scan architecture is secured through a clock and data recovery (CDR) technique. This is a manuscript based thesis and the results of this study have been published in two conference proceedings. The latest results have also been prepared as an article for submission to a high rank conference

An Energy-Efficient Reconfigurable Mobile Memory Interface for Computing Systems

The critical need for higher power efficiency and bandwidth transceiver design has significantly increased as mobile devices, such as smart phones, laptops, tablets, and ultra-portable personal digital assistants continue to be constructed using heterogeneous intellectual properties such as central processing units (CPUs), graphics processing units (GPUs), digital signal processors, dynamic random-access memories (DRAMs), sensors, and graphics/image processing units and to have enhanced graphic computing and video processing capabilities. However, the current mobile interface technologies which support CPU to memory communication (e.g. baseband-only signaling) have critical limitations, particularly super-linear energy consumption, limited bandwidth, and non-reconfigurable data access. As a consequence, there is a critical need to improve both energy efficiency and bandwidth for future mobile devices.;The primary goal of this study is to design an energy-efficient reconfigurable mobile memory interface for mobile computing systems in order to dramatically enhance the circuit and system bandwidth and power efficiency. The proposed energy efficient mobile memory interface which utilizes an advanced base-band (BB) signaling and a RF-band signaling is capable of simultaneous bi-directional communication and reconfigurable data access. It also increases power efficiency and bandwidth between mobile CPUs and memory subsystems on a single-ended shared transmission line. Moreover, due to multiple data communication on a single-ended shared transmission line, the number of transmission lines between mobile CPU and memories is considerably reduced, resulting in significant technological innovations, (e.g. more compact devices and low cost packaging to mobile communication interface) and establishing the principles and feasibility of technologies for future mobile system applications. The operation and performance of the proposed transceiver are analyzed and its circuit implementation is discussed in details. A chip prototype of the transceiver was implemented in a 65nm CMOS process technology. In the measurement, the transceiver exhibits higher aggregate data throughput and better energy efficiency compared to prior works

Realization Limits of Impulse-Radio UWB Indoor Localization Systems

In this work, the realization limits of an impulse-based Ultra-Wideband (UWB) localization system for indoor applications have been thoroughly investigated and verified by measurements. The analysis spans from the position calculation algorithms, through hardware realization and modeling, up to the localization experiments conducted in realistic scenarios. The main focus was put on identification and characterization of limiting factors as well as developing methods to overcome them

Ring-Based Resonant Standing Wave Oscillators for 3D Clocking Applications

Ring-based resonant standing wave oscillators have been shown to be a useful clocking tech-nique that can distribute and generate a high frequency, low skew, low power, and stable clock signal. By using through-silicon-vias, this type of standing wave oscillator can be used to gener-ate the clocking scheme for 3D integrated circuits. In this thesis, we propose the use of such 3D standing wave oscillators and show how independent 3D oscillators in different stacks can syn-chronize through the use of a redistribution layer stub. Inter-chip clock synchronization is then accomplished without the need for a PLL. In addition, we propose the first 3D ring-based resonant standing wave oscillator bootstrap and reset circuit to initialize and stop oscillation. Using a 3D ring-based resonant standing wave oscillator, we propose a ring-based data fabric for 3D stacked DRAM and compare the results with existing approaches such as High Bandwidth Memory (HBM) or Wide I/O memory. We show that our Memory Architecture using a Ring-based Scheme (MARS) can provide the increases in speed necessary to overcome current memory bottlenecks, and can scale effectively as future 3D stacks become larger. Our MARS can trade off power, throughput, and latency to match different application requirements. By using a narrow bus, and connecting it to all channels, the MARS8 can provide an alternative memory configuration with ∼ 6.9× lower power consumption than HBM, and ∼ 2.7× faster speeds than Wide I/O. Using multiple ring topologies in the same stack, the channel count can double from 8 to 16, and then to 32. This is possible since MARS uses about 4× fewer TSVs per channel than HBM or Wide I/O. This provides speeds up to ∼ 4.2× faster than traditional HBM. This scalable architecture allows higher throughput and faster system performance for next-generation DRAM. The MARS topology proposed in this thesis can be used in a variety of computing systems, from lightweight IoT to large-scale data centers

Time-Domain/Digital Frequency Synchronized Hysteresis Based Fully Integrated Voltage Regulator

abstract: Power management integrated circuit (PMIC) design is a key module in almost all electronics around us such as Phones, Tablets, Computers, Laptop, Electric vehicles, etc. The on-chip loads such as microprocessors cores, memories, Analog/RF, etc. requires multiple supply voltage domains. Providing these supply voltages from off-chip voltage regulators will increase the overall system cost and limits the performance due to the board and package parasitics. Therefore, an on-chip fully integrated voltage regulator (FIVR) is required. The dissertation presents a topology for a fully integrated power stage in a DC-DC buck converter achieving a high-power density and a time-domain hysteresis based highly integrated buck converter. A multi-phase time-domain comparator is proposed in this work for implementing the hysteresis control, thereby achieving a process scaling friendly highly digital design. A higher-order LC notch filter along with a flying capacitor which couples the input and output voltage ripple is implemented. The power stage operates at 500 MHz and can deliver a maximum power of 1.0 W and load current of 1.67 A, while occupying 1.21 mm2 active die area. Thus achieving a power density of 0.867 W/mm2 and current density of 1.377 A/mm2. The peak efficiency obtained is 71% at 780 mA of load current. The power stage with the additional off-chip LC is utilized to design a highly integrated current mode hysteretic buck converter operating at 180 MHz. It achieves 20 ns of settling and 2-5 ns of rise/fall time for reference tracking. The second part of the dissertation discusses an integrated low voltage switched-capacitor based power sensor, to measure the output power of a DC-DC boost converter. This approach results in a lower complexity, area, power consumption, and a lower component count for the overall PV MPPT system. Designed in a 180 nm CMOS process, the circuit can operate with a supply voltage of 1.8 V. It achieves a power sense accuracy of 7.6%, occupies a die area of 0.0519 mm2, and consumes 0.748 mW of power.Dissertation/ThesisDoctoral Dissertation Electrical Engineering 201

Wireless Testing of Integrated Circuits.

Integrated circuits (ICs) are usually tested during manufacture by means of automatic testing equipment (ATE) employing probe cards and needles that make repeated physical contact with the ICs under test. Such direct-contact probing is very costly and imposes limitations on the use of ATE. For example, the probe needles must be frequently cleaned or replaced, and some emerging technologies such as three-dimensional ICs cannot be probed at all. As an alternative to conventional probe-card testing, wireless testing has been proposed. It mitigates many of the foregoing problems by replacing probe needles and contact points with wireless communication circuits. However, wireless testing also raises new problems which are poorly understood such as: What is the most suitable wireless communication technique to employ, and how well does it work in practice? This dissertation addresses the design and implementation of circuits to support wireless testing of ICs. Various wireless testing methods are investigated and evaluated with respect to their practicality. The research focuses on near-field capacitive communication because of its efficiency over the very short ranges needed during IC manufacture. A new capacitive channel model including chip separation, cross-talk, and misalignment effects is proposed and validated using electro-magnetic simulation studies to provide the intuitions for efficient antenna and circuit design. We propose a compact clock and data recovery architecture to avoid a dedicated clock channel. An analytical model which predicts the DC-level fluctuation due to the capacitive channel is presented. Based on this model, feed-forward clock selection is designed to enhance performance. A method to select proper channel termination is discussed to maximize the channel efficiency for return-to-zero signaling. Two prototype ICs incorporating wireless testing systems were fabricated and tested with the proposed methods of testing digital circuits. Both successfully demonstrated gigahertz communication speeds with a bit-error rate less than 10^−11. A third prototype IC containing analog voltage measurement circuits was implemented to determine the feasibility of wirelessly testing analog circuits. The fabricated prototype achieved satisfactory voltage measurement with 1 mV resolution. Our work demonstrates the validity of the proposed models and the feasibility of near-field capacitive communication for wireless testing of ICs.PHDElectrical EngineeringUniversity of Michigan, Horace H. Rackham School of Graduate Studieshttp://deepblue.lib.umich.edu/bitstream/2027.42/93993/1/duelee_1.pd

From FPGA to ASIC: A RISC-V processor experience

This work document a correct design flow using these tools in the Lagarto RISC- V Processor and the RTL design considerations that must be taken into account, to move from a design for FPGA to design for ASIC

Millimeter-Scale and Energy-Efficient RF Wireless System

This dissertation focuses on energy-efficient RF wireless system with millimeter-scale dimension, expanding the potential use cases of millimeter-scale computing devices. It is challenging to develop RF wireless system in such constrained space. First, millimeter-sized antennae are electrically-small, resulting in low antenna efficiency. Second, their energy source is very limited due to the small battery and/or energy harvester. Third, it is required to eliminate most or all off-chip devices to further reduce system dimension. In this dissertation, these challenges are explored and analyzed, and new methods are proposed to solve them. Three prototype RF systems were implemented for demonstration and verification. The first prototype is a 10 cubic-mm inductive-coupled radio system that can be implanted through a syringe, aimed at healthcare applications with constrained space. The second prototype is a 3x3x3 mm far-field 915MHz radio system with 20-meter NLOS range in indoor environment. The third prototype is a low-power BLE transmitter using 3.5x3.5 mm planar loop antenna, enabling millimeter-scale sensors to connect with ubiquitous IoT BLE-compliant devices. The work presented in this dissertation improves use cases of millimeter-scale computers by presenting new methods for improving energy efficiency of wireless radio system with extremely small dimensions. The impact is significant in the age of IoT when everything will be connected in daily life.PHDElectrical EngineeringUniversity of Michigan, Horace H. Rackham School of Graduate Studieshttps://deepblue.lib.umich.edu/bitstream/2027.42/147686/1/yaoshi_1.pd

Design of a Dual Band Local Positioning System

This work presents a robust dual band local positioning system (LPS) working in the 2.4GHz and 5.8GHz industrial science medical (ISM) bands. Position measurement is based on the frequency-modulated continuous wave (FMCW) radar approach, which uses radio frequency (RF) chirp signals for propagation time and therefore distance measurements. Contrary to state of the art LPS, the presented system uses data from both bands to improve accuracy, precision and robustness. A complete system prototype is designed consisting of base stations and tags encapsulating most of the RF and analogue signal processing in custom integrated circuits. This design approach allows to reduce size and power consumption compared to a hybrid system using off-the-shelf components. Key components are implemented using concepts, which support operation in multiple frequency bands, namely, the receiver consisting of a low noise amplifier (LNA), mixer, frequency synthesizer with a wide band voltage-controlled oscillator (VCO) having broadband chirp generation capabilities and a dual band power amplifier. System imperfections occurring in FMCW radar systems are modelled. Effects neglected in literature such as compression, intermodulation, the influence of automatic gain control, blockers and spurious emissions are modeled. The results are used to derive a specification set for the circuit design. Position estimation from measured distances is done using an enhanced version of the grid search algorithm, which makes use of data from multiple frequency bands. The algorithm is designed to be easily and efficiently implemented in embedded systems. Measurements show a coverage range of the system of at least 245m. Ranging accuracy in an outdoor scenario can be as low as 8.2cm. Comparative dual band position measurements prove an effective outlier filtering in indoor and outdoor scenarios compared to single band results, yielding in a large gain of accuracy. Positioning accuracy in an indoor scenario with an area of 276m² can be improved from 1.27m at 2.4GHz and 1.86m at 5.8GHz to only 0.38m in the dual band case, corresponding to an improvement by at least a factor of 3.3. In a large outdoor scenario of 4.8 km², accuracy improves from 1.88m at 2.4GHz and 5.93m at 5.8GHz to 0.68m with dual band processing, which is a factor of at least 2.8.Die vorliegende Arbeit befasst sich mit dem Entwurf eines robusten lokalen Positionierungssystems (LPS), welches in den lizenzfreien Frequenzbereichen für industrielle, wissenschaftliche und medizinische Zwecke (industrial, scientific, medical, ISM) bei 2,4GHz und 5,8GHz arbeitet. Die Positionsbestimmung beruht auf dem Prinzip des frequenzmodulierten Dauerstrichradars (frequency modulated continuous wave, FMCW-Radar), welches hochfrequente Rampensignale für Laufzeitmessungen und damit Abstandsmessungen benutzt. Im Gegensatz zu aktuellen Arbeiten auf diesem Gebiet benutzt das vorgestellte System Daten aus beiden Frequenzbändern zur Erhöhung der Genauigkeit und Präzision sowie Verbesserung der Robustheit. Ein Prototyp des kompletten Systems bestehend aus Basisstationen und mobilen Stationen wurde entworfen. Fast die gesamte analoge hochfrequente Signalverarbeitungskette wurde als anwendungsspezifische integrierte Schaltung realisiert. Verglichen mit Systemen aus Standardkomponenten erlaubt dieser Ansatz die Miniaturisierung der Systemkomponenten und die Einsparung von Leistung. Schlüsselkomponenten wurden mit Konzepten für mehrbandige oder breitbandige Schaltungen entworfen. Dabei wurden Sender und Empfänger bestehend aus rauscharmem Verstärker, Mischer und Frequenzsynthesizer mit breitbandiger Frequenzrampenfunktion implementiert. Außerdem wurde ein Leistungsverstärker für die gleichzeitige Nutzung der beiden definierten Frequenzbänder entworfen. Um Spezifikationen für den Schaltungsentwurf zu erhalten, wurden in der Fachliteratur vernachlässigte Nichtidealitäten von FMCW-Radarsystemen modelliert. Dazu gehören Signalverzerrungen durch Kompression oder Intermodulation, der Einfluss der automatischen Verstärkungseinstellung sowie schmalbandige Störer und Nebenschwingungen. Die Ergebnisse der Modellierung wurden benutzt, um eine Spezifikation für den Schaltungsentwurf zu erhalten. Die Schätzung der Position aus gemessenen Abständen wurde über eine erweiterte Version des Gittersuchalgorithmus erreicht. Dieser nutzt die Abstandsmessdaten aus beiden Frequenzbändern. Der Algorithmus ist so entworfen, dass er effizient in einem eingebetteten System implementiert werden kann. Messungen zeigen eine maximale Reichweite des Systems von mindestens 245m. Die Genauigkeit von Abstandsmessungen im Freiland beträgt 8,2cm. Positionsmessungen wurden unter Verwendung beider Einzelbänder durchgeführt und mit den Ergebnissen des Zweiband-Gittersuchalgorithmus verglichen. Damit konnte eine starke Verbesserung der Positionsgenauigkeit erreicht werden. Die Genauigkeit in einem Innenraum mit einer Grundfläche von 276m² kann verbessert werden von 1,27m bei 2,4GHz und 1,86m bei 5,8GHz zu nur 0,38m im Zweibandverfahren. Das entspricht einer Verbesserung um einen Faktor von mindestens 3,3. In einem größeren Außenszenario mit einer Fläche von 4,8 km² verbessert sich die Genauigkeit um einen Faktor von mindestens 2,8 von 1,88m bei 2,4GHz und 5,93m bei 5,8GHz auf 0,68m bei Nutzung von Daten aus beiden Frequenzbändern