A Low-Power, Reconfigurable, Pipelined ADC with Automatic Adaptation for Implantable Bioimpedance Applications

Biomedical monitoring systems that observe various physiological parameters or electrochemical reactions typically cannot expect signals with fixed amplitude or frequency as signal properties can vary greatly even among similar biosignals. Furthermore, advancements in biomedical research have resulted in more elaborate biosignal monitoring schemes which allow the continuous acquisition of important patient information. Conventional ADCs with a fixed resolution and sampling rate are not able to adapt to signals with a wide range of variation. As a result, reconfigurable analog-to-digital converters (ADC) have become increasingly more attractive for implantable biosensor systems. These converters are able to change their operable resolution, sampling rate, or both in order convert changing signals with increased power efficiency. Traditionally, biomedical sensing applications were limited to low frequencies. Therefore, much of the research on ADCs for biomedical applications focused on minimizing power consumption with smaller bias currents resulting in low sampling rates. However, recently bioimpedance monitoring has become more popular because of its healthcare possibilities. Bioimpedance monitoring involves injecting an AC current into a biosample and measuring the corresponding voltage drop. The frequency of the injected current greatly affects the amplitude and phase of the voltage drop as biological tissue is comprised of resistive and capacitive elements. For this reason, a full spectrum of measurements from 100 Hz to 10-100 MHz is required to gain a full understanding of the impedance. For this type of implantable biomedical application, the typical low power, low sampling rate analog-to-digital converter is insufficient. A different optimization of power and performance must be achieved. Since SAR ADC power consumption scales heavily with sampling rate, the converters that sample fast enough to be attractive for bioimpedance monitoring do not have a figure-of-merit that is comparable to the slower converters. Therefore, an auto-adapting, reconfigurable pipelined analog-to-digital converter is proposed. The converter can operate with either 8 or 10 bits of resolution and with a sampling rate of 0.1 or 20 MS/s. Additionally, the resolution and sampling rate are automatically determined by the converter itself based on the input signal. This way, power efficiency is increased for input signals of varying frequency and amplitude

Integrated Electronics for Wireless Imaging Microsystems with CMUT Arrays

Integration of transducer arrays with interface electronics in the form of single-chip CMUT-on-CMOS has emerged into the field of medical ultrasound imaging and is transforming this field. It has already been used in several commercial products such as handheld full-body imagers and it is being implemented by commercial and academic groups for Intravascular Ultrasound and Intracardiac Echocardiography. However, large attenuation of ultrasonic waves transmitted through the skull has prevented ultrasound imaging of the brain. This research is a prime step toward implantable wireless microsystems that use ultrasound to image the brain by bypassing the skull. These microsystems offer autonomous scanning (beam steering and focusing) of the brain and transferring data out of the brain for further processing and image reconstruction. The objective of the presented research is to develop building blocks of an integrated electronics architecture for CMUT based wireless ultrasound imaging systems while providing a fundamental study on interfacing CMUT arrays with their associated integrated electronics in terms of electrical power transfer and acoustic reflection which would potentially lead to more efficient and high-performance systems. A fully wireless architecture for ultrasound imaging is demonstrated for the first time. An on-chip programmable transmit (TX) beamformer enables phased array focusing and steering of ultrasound waves in the transmit mode while its on-chip bandpass noise shaping digitizer followed by an ultra-wideband (UWB) uplink transmitter minimizes the effect of path loss on the transmitted image data out of the brain. A single-chip application-specific integrated circuit (ASIC) is de- signed to realize the wireless architecture and interface with array elements, each of which includes a transceiver (TRX) front-end with a high-voltage (HV) pulser, a high-voltage T/R switch, and a low-noise amplifier (LNA). Novel design techniques are implemented in the system to enhance the performance of its building blocks. Apart from imaging capability, the implantable wireless microsystems can include a pressure sensing readout to measure intracranial pressure. To do so, a power-efficient readout for pressure sensing is presented. It uses pseudo-pseudo differential readout topology to cut down the static power consumption of the sensor for further power savings in wireless microsystems. In addition, the effect of matching and electrical termination on CMUT array elements is explored leading to new interface structures to improve bandwidth and sensitivity of CMUT arrays in different operation regions. Comprehensive analysis, modeling, and simulation methodologies are presented for further investigation.Ph.D

Novel Front-end Electronics for Time Projection Chamber Detectors

Este trabajo ha sido realizado en la Organización Europea para la Investigación Nuclear (CERN) y forma parte del proyecto de investigación Europeo para futuros aceleradores lineales (EUDET). En física de partículas existen diferentes categorías de detectores de partículas. El diseño presentado esta centrado en un tipo particular de detector de trayectoria de partículas denominado TPC (Time Projection Chamber) que proporciona una imagen en tres dimensiones de las partículas eléctricamente cargadas que atraviesan su volumen gaseoso. La tesis incluye un estudio de los objetivos para futuros detectores, resumiendo los parámetros que un sistema de adquisición de datos debe cumplir en esos casos. Además, estos requisitos son comparados con los actuales sistemas de lectura utilizados en diferentes detectores TPC. Se concluye que ninguno de los sistemas cumple las restrictivas condiciones. Algunos de los principales objetivos para futuros detectores TPC son un altísimo nivel de integración, incremento del número de canales, electrónica más rápida y muy baja potencia. El principal inconveniente del estado del arte de los sistemas anteriores es la utilización de varios circuitos integrados en la cadena de adquisición. Este hecho hace imposible alcanzar el altísimo nivel de integración requerido para futuros detectores. Además, un aumento del número de canales y frecuencia de muestreo haría incrementar hasta valores no permitidos la potencia utilizada. Y en consecuencia, incrementar la refrigeración necesaria (en caso de ser posible). Una de las novedades presentadas es la integración de toda la cadena de adquisición (filtros analógicos de entrada, conversor analógico-digital (ADC) y procesado de señal digital) en un único circuito integrado en tecnología de 130nm. Este chip es el primero que realiza esta altísima integración para detectores TPC. Por otro lado, se presenta un análisis detallado de los filtros de procesado de señal. Los objetivos más importantes es la reduccióGarcía García, EJ. (2012). Novel Front-end Electronics for Time Projection Chamber Detectors [Tesis doctoral no publicada]. Universitat Politècnica de València. https://doi.org/10.4995/Thesis/10251/16980Palanci

INTEGRATED SINGLE-PHOTON SENSING AND PROCESSING PLATFORM IN STANDARD CMOS

Practical implementation of large SPAD-based sensor arrays in the standard CMOS process has been fraught with challenges due to the many performance trade-offs existing at both the device and the system level [1]. At the device level the performance challenge stems from the suboptimal optical characteristics associated with the standard CMOS fabrication process. The challenge at the system level is the development of monolithic readout architecture capable of supporting the large volume of dynamic traffic, associated with multiple single-photon pixels, without limiting the dynamic range and throughput of the sensor. Due to trade-offs in both functionality and performance, no general solution currently exists for an integrated single-photon sensor in standard CMOS single photon sensing and multi-photon resolution. The research described herein is directed towards the development of a versatile high performance integrated SPAD sensor in the standard CMOS process. Towards this purpose a SPAD device with elongated junction geometry and a perimeter field gate that features a large detection area and a highly reduced dark noise has been presented and characterized. Additionally, a novel front-end system for optimizing the dynamic range and after-pulsing noise of the pixel has been developed. The pixel is also equipped with an output interface with an adjustable pulse width response. In order to further enhance the effective dynamic range of the pixel a theoretical model for accurate dead time related loss compensation has been developed and verified. This thesis also introduces a new paradigm for electrical generation and encoding of the SPAD array response that supports fully digital operation at the pixel level while enabling dynamic discrete time amplitude encoding of the array response. Thus offering a first ever system solution to simultaneously exploit both the dynamic nature and the digital profile of the SPAD response. The array interface, comprising of multiple digital inputs capacitively coupled onto a shared quasi-floating sense node, in conjunction with the integrated digital decoding and readout electronics represents the first ever solid state single-photon sensor capable of both photon counting and photon number resolution. The viability of the readout architecture is demonstrated through simulations and preliminary proof of concept measurements

Low-power adaptive control scheme using switching activity measurement method for reconfigurable analog-to-digital converters

Power consumption is a critical issue for portable devices. The ever-increasing demand for multimode wireless applications and the growing concerns towards power-aware green technology make dynamically reconfigurable hardware an attractive solution for overcoming the power issue. This is due to its advantages of flexibility, reusability, and adaptability. During the last decade, reconfigurable analog-to-digital converters (ReADCs) have been used to support multimode wireless applications. With the ability to adaptively scale the power consumption according to different operation modes, reconfigurable devices utilise the power supply efficiently. This can prolong battery life and reduce unnecessary heat emission to the environment. However, current adaptive mechanisms for ReADCs rely upon external control signals generated using digital signal processors (DSPs) in the baseband. This thesis aims to provide a single-chip solution for real-time and low-power ReADC implementations that can adaptively change the converter resolution according to signal variations without the need of the baseband processing. Specifically, the thesis focuses on the analysis, design and implementation of a low-power digital controller unit for ReADCs. In this study, the following two important reconfigurability issues are investigated: i) the detection mechanism for an adaptive implementation, and ii) the measure of power and area overheads that are introduced by the adaptive control modules. This thesis outlines four main achievements to address these issues. The first achievement is the development of the switching activity measurement (SWAM) method to detect different signal components based upon the observation of the output of an ADC. The second achievement is a proposed adaptive algorithm for ReADCs to dynamically adjust the resolution depending upon the variations in the input signal. The third achievement is an ASIC implementation of the adaptive control module for ReADCs. The module achieves low reconfiguration overheads in terms of area and power compared with the main analog part of a ReADC. The fourth achievement is the development of a low-power noise detection module using a conventional ADC for signal improvement. Taken together, the findings from this study demonstrate the potential use of switching activity information of an ADC to adaptively control the circuits, and simultaneously expanding the functionality of the ADC in electronic systems

Integrated Circuits and Systems for Smart Sensory Applications

Connected intelligent sensing reshapes our society by empowering people with increasing new ways of mutual interactions. As integration technologies keep their scaling roadmap, the horizon of sensory applications is rapidly widening, thanks to myriad light-weight low-power or, in same cases even self-powered, smart devices with high-connectivity capabilities. CMOS integrated circuits technology is the best candidate to supply the required smartness and to pioneer these emerging sensory systems. As a result, new challenges are arising around the design of these integrated circuits and systems for sensory applications in terms of low-power edge computing, power management strategies, low-range wireless communications, integration with sensing devices. In this Special Issue recent advances in application-specific integrated circuits (ASIC) and systems for smart sensory applications in the following five emerging topics: (I) dedicated short-range communications transceivers; (II) digital smart sensors, (III) implantable neural interfaces, (IV) Power Management Strategies in wireless sensor nodes and (V) neuromorphic hardware

Energy-Efficient Time-Based Encoders and Digital Signal Processors in Continuous Time

Continuous-time (CT) data conversion and continuous-time digital signal processing (DSP) are an interesting alternative to conventional methods of signal conversion and processing. This alternative proposes time-based encoding that may not suffer from aliasing; shows superior spectral properties (e.g. no quantization noise floor); and enables time-based, event-driven, flexible signal processing using digital circuits, thus scaling well with technology. Despite these interesting features, this approach has so far been limited by the CT encoder, due to both its relatively poor energy efficiency and the constraints it imposes on the subsequent CT DSP. In this thesis, we present three principles that address these limitations and help improve the CT ADC/DSP system. First, an adaptive-resolution encoding scheme that achieves first-order reconstruction with simple circuitry is proposed. It is shown that for certain signals, the scheme can significantly reduce the number of samples generated per unit of time for a given accuracy compared to schemes based on zero-order-hold reconstruction, thus promising to lead to low dynamic power dissipation at the system level. Presented next is a novel time-based CT ADC architecture, and associated encoding scheme, that allows a compact, energy-efficient circuit implementation, and achieves first-order quantization error spectral shaping. The design of a test chip, implemented in a 0.65-V 28-nm FDSOI process, that includes this CT ADC and a 10-tap programmable FIR CT DSP to process its output is described. The system achieves 32 dB – 42 dB SNDR over a 10 MHz – 50 MHz bandwidth, occupies 0.093 mm2, and dissipates 15 µW–163 µW as the input amplitude goes from zero to full scale. Finally, an investigation into the possibility of CT encoding using voltage-controlled oscillators is undertaken, and it leads to a CT ADC/DSP system architecture composed primarily of asynchronous digital delays. The latter makes the system highly digital and technology-scaling-friendly and, hence, is particularly attractive from the point of view of technology migration. The design of a test chip, where this delay-based CT ADC/DSP system architecture is used to implement a 16-tap programmable FIR filter, in a 1.2-V 28-nm FDSOI process, is described. Simulations show that the system will achieve a 33 dB – 40 dB SNDR over a 600 MHz bandwidth, while dissipating 4 mW

Image compression and energy harvesting for energy constrained sensors

Title from PDF of title page, viewed on June 21, 2013Dissertation advisor: Walter D. Leon-SalasVitaIncludes bibliographic references (pages 176-[187])Thesis (Ph.D.)--School of Computing and Engineering. University of Missouri--Kansas City, 2013The advances in complementary metal-oxide-semiconductor (CMOS) technology have led to the integration of all components of electronic system into a single integrated circuit. Ultra-low power circuit techniques have reduced the power consumption of circuits. Moreover, solar cells with improved efficiency can be integrated on chip to harvest energy from sunlight. As a result of all the above, a new class of miniaturized electronic systems known as self-powered system on a chip has emerged. There is an increasing research interest in the area of self-powered devices which provide cost-effective solutions especially when these devices are used in the areas that changing or replacing batteries is too costly. Therefore, image compression and energy harvesting are studied in this dissertation. The integration of energy harvesting, image compression, and an image sensor on the same chip provides the energy source to charge a battery, reduces the data rate, and improves the performance of wireless image sensors. Integrated circuits of image compression, solar energy harvesting, and image sensors are studied, designed, and analyzed in this work. In this dissertation, a hybrid image sensor that can perform the tasks of sensing and energy harvesting is presented. Photodiodes of hybrid image sensor can be programmed as image sensors or energy harvesting cells. The hybrid image sensor can harvest energy in between frames, in sleep mode, and even when it is taking images. When sensing images and harvesting energy are both needed at the same time, some pixels have to work as sensing pixels, and the others have to work as solar cells. Since some pixels are devoted to harvest energy, the resolution of the image will be reduced. To preserve the resolution or to keep the fair resolution when a lot of energy collection is needed, image reconstruction algorithms and compressive sensing theory provide solutions to achieve a good image quality. On the other hand, when the battery has enough charge, image compression comes into the picture. Multiresolution decomposition image compression provides a way to compress image data in order to reduce the energy need from data transmission. The solution provided in this dissertation not only harvests energy but also saves energy resulting long lasting wireless sensors. The problem was first studied at the system level to identify the best system-level configuration which was then implemented on silicon. As a proof of concept, a 32 x 32 array of hybrid image sensor, a 32 x 32 array of image sensor with multiresolution decomposition compression, and a compressive sensing converter have been designed and fabricated in a standard 0.5 [micrometer] CMOS process. Printed circuit broads also have been designed to test and verify the proposed and fabricated chips. VHDL and Matlab codes were written to generate the proper signals to control, and read out data from chips. Image processing and recovery were carried out in Matlab. DC-DC converters were designed to boost the inherently low voltage output of the photodiodes. The DC-DC converter has also been improved to increase the efficiency of power transformation.Introduction -- Hybrid imager system and circuit design -- Hybrid imager energy harvesting and image acquisition results and discussion -- Detailed description and mathematical analysis for a circuit of energy harvesting using on-chip solar cells -- Multiresolution decomposition for lossless and near-lossless compression -- An incremental [sigma-delta] converter for compressive sensing -- Detailed description of a sigma-delta random demodulator converter architecture for compressive sensing applications -- Conclusion -- Appendix A. Chip pin-out -- Appendix B. Schematics -- Appendix C. Pictures of custom PC

CMOS ASIC Design of Multi-frequency Multi-constellation GNSS Front-ends

With the emergence of the new global navigation satellite systems (GNSSs) such as Galileo, COMPASS and GLONASS, the US Global Positioning System (GPS) has new competitors. This multiplicity of constellations will offer new services and a much better satellite coverage. Public regulated service (PRS) is one of these new services that Galileo, the first global positioning service under civilian control, will offers. The PRS is a proprietary encrypted navigation designed to be more reliable and robust against jamming and provides premium quality in terms of position and timing and continuity of service, but it requires the use of FEs with extended capabilities. The project that this thesis starts from, aims to develop a dual frequency (E1 and E6) PRS receiver with a focus on a solution for professional applications that combines affordability and robustness. To limit the production cost, the choice of a monolithic design in a multi-purpose 0.18 µm complementary metal-oxide-semiconductor (CMOS) technology have been selected, and to reduce the susceptibility to interference, the targeted receiver is composed of two independent FEs. The first ASIC described here is such FEs bundle. Each FE is composed of a radio frequency (RF) chain that includes a low-noise amplifier (LNA), a quadrature mixer, a frequency synthesizer (FS), two intermediate frequency (IF) filters, two variable-gain amplifiers (VGAs) and two 6-bit flash analog-to-digital converters (ADCs). Each have an IF bandwidth of 50 MHz to accommodate the wide-band PRS signals. The FE achieves a 30 dB of dynamic gain control at each channel. The complete receivers occupies a die area of 11.5 mm2 while consuming 115 mW from a supply of a 1.8 V. The second ASIC that targets civilian applications, is a reconfigurable single-channel FE that permits to exploit the interoperability among GNSSs. The FE can operate in two modes: a ¿narrow-band mode¿, dedicated to Beidou-B1 with an IF bandwidth of 8 MHz, and a ¿wide-band mode¿ with an IF bandwidth of 23 MHz, which can accommodate simultaneous reception of Beidou-B1/GPS-L1/Galileo-E1. These two modes consumes respectively 22.85 mA and 28.45 mA from a 1.8 V supply. Developed with the best linearity in mind, the FE shows very good linearity with an input-referred 1 dB compression point (IP1dB) of better than -27.6 dBm. The FE gain is stepwise flexible from 39 dB and to a maximum of 58 dB. The complete FE occupies a die area of only 2.6 mm2 in a 0.18 µm CMOS. To also accommodate the wide-band PRS signals in the IF section of the FE, a highly selective wide-tuning-range 4th-order Gm-C elliptic low-pass filter is used. It features an innovative continuous tuning circuit that adjusts the bias current of the Gm cell¿s input stage to control the cutoff frequency. With this circuit, the power consumption is proportional to the cutoff frequency thus the power efficiency is achieved while keeping the linearity near constant. Thanks to a Gm switching technique, which permit to keep the signal path switchless, the filter shows an extended tuning of the cutoff frequency that covers continuously a range from 7.4 MHz to 27.4 MHz. Moreover the abrupt roll-off of up to 66 dB/octave, can mitigate out-of-band interference. The filter consumes 2.1 mA and 7.5 mA at its lowest and highest cutoff frequencies respectively, and its active area occupies, 0.23 mm2. It achieves a high input-referred third-order intercept point (IIP3) of up to -1.3 dBVRMS