Adaptive relay techniques for OFDM-based cooperative communication systems

Cooperative communication has been considered as a cost-effective manner to exploit the spatial diversity, improve the quality-of-service and extend transmission coverage. However, there are many challenges faced by cooperative systems which use relays to forward signals to the destination, such as the accumulation of multipath channels, complex resource allocation with the bidirectional asymmetric traffic and reduction of transmission efficiency caused by additional relay overhead. In this thesis, we aim to address the above challenges of cooperative communications, and design the efficient relay systems. Starting with the channel accumulation problem in the amplify-and-forward relay system, we proposed two adaptive schemes for single/multiple-relay networks respectively. These schemes exploit an adaptive guard interval (GI) technique to cover the accumulated delay spread and enhance the transmission efficiency by limiting the overhead. The proposed GI scheme can be implemented without any extra control signal. Extending the adaptive GI scheme to multiple-relay systems, we propose a relay selection strategy which achieves the trade-off between the transmission reliability and overhead by considering both the channel gain and the accumulated delay spread. We then consider resource allocation problem in the two-way decode-and-forward relay system with asymmetric traffic loads. Two allocation algorithms are respectively investigated for time-division and frequency-division relay systems to maximize the end-to-end capacity of the two-way system under a capacity ratio constraint. For the frequency-division systems, a balanced end-to-end capacity is defined as the objective function which combines the requirements of maximizing the end-to-end capacity and achieving the capacity ratio. A suboptimal algorithm is proposed for the frequency-division systems which separates subcarrier allocation and time/power allocation. It can achieve the similar performance with the optimal one with reduced complexity. In order to further enhance the transmission reliability and maintaining low processing delay, we propose an equalize-and-forward (EF) relay scheme. The EF relay equalizes the channel between source and relay to eliminate the channel accumulation without signal regeneration. To reduce the processing time, an efficient parallel structure is applied in the EF relay. Numerical results show that the EF relay exhibits low outage probability at the same data rate as compared to AF and DF schemes

OFDM Communication with Cooperative Relays

Signal fading due to multi-path propagation is one of the major impairments to meet the demands of next generation wireless networks for high data rate services. To mitigate the fading effects, time, frequency, and spatial diversity techniques or their hybrid can be used. Among different types of diversity techniques, spatial diversity is of special interest as is does not incur system losses in terms of delay and bandwidth efficiency.TelecommunicationsElectrical Engineering, Mathematics and Computer Scienc

Codificação distribuída em sistemas com diversidade cooperativa

Doutoramento em Engenharia ElectrotécnicaO presente trabalho propõe-se a divulgar as mais significativas técnicas de esquemas cooperativos, de forma a ultrapassar alguns dos problemas dos sistemas móveis sem fios da próxima geração, estendendo a área de cobertura destes sistemas, assim como a sua capacidade e fiabilidade. O estudo de diversos esquemas cooperativos é efetuado em termos de capacidade e de taxa de erros, fazendo variar o número de relays e de antenas em cada elemento do sistema. Diversos algoritmos com aplicação em sistemas cooperativos são desenvolvidos e propostos ao longo desta tese, como códigos espaço-frequência aplicados de forma distribuída nos relays, para sistemas baseados na tecnologia OFDM e sob diversos cenários próximos da realidade. Os sistemas cooperativos são particularmente úteis em situações em que o caminho direto entre dois terminais não está acessível ou tem uma fraca qualidade de transmissão. Tendo este aspeto em consideração, e pretendendo ter a máxima eficiência espetral e máxima diversidade, um algoritmo com precodificação é também proposto para múltiplos relays, cada um equipado com uma ou duas antenas. A formulação matemática associada aos algoritmos propostos é apresentada, assim como a derivação da probabilidade de erro teórica. O desempenho dos sistemas assistidos por relays usando os algoritmos propostos é comparado em relação a outros esquemas cooperativos equivalentes e a esquemas não-cooperativos, considerando cenários com diferentes qualidades de canal, daí advindo importantes conclusões em relação a estes sistemas.Cooperative schemes are promising solutions for cellular wireless networks aiming to improve system fairness, extend coverage and increase capacity. Measurements of these system performances are made in terms of BER and capacity for different configurations, by varying the number of relays and of antennas equipping each node. In this work we propose and evaluate distributed space-frequency codes applied to cooperative systems in a distributed way, with application in OFDM systems and considering realistic scenarios. Moreover, the use of relays is of significant interest to allow radio access in situations where a direct path is not available or has poor quality. Thus, a data precoded relay-assisted scheme is also proposed for a system cooperating with multiple relays, each equipped with either a single antenna or two-antenna array. Mathematical formulation of the proposed algorithms is derived as well as the pairwise error probability. We further present the performances of the proposed algorithms apllied in relay-assisted schemes, and compare them with equivalent cooperative and non-cooperative schemes, for several channel quality scenarios, through which important conclusions are achieved.FCT/FS

Mitigating PAPR in cooperative wireless networks with frequency selective channels and relay selection

The focus of this thesis is peak-to-average power ratio (PAPR) reduction in cooperative wireless networks which exploit orthogonal frequency division multiplexing in transmission. To reduce the PAPR clipping is employed at the source node. The first contribution focuses upon an amplify-and-forward (AF) type network with four relay nodes which exploits distributed closed loop extended orthogonal space frequency block coding to improve end-to-end performance. Oversampling and filtering are used at the source node to reduce out-of-band interference and the iterative amplitude reconstruction decoding technique is used at the destination node to mitigate in-band distortion which is introduced by the clipping process. In addition, by exploiting quantized group feedback and phase rotation at two of the relay nodes, the system achieves full cooperative diversity in addition to array gain. The second contribution area is outage probability analysis in the context of multi-relay selection in a cooperative AF network with frequency selective fading channels. The gains of time domain multi-path fading channels with L paths are modeled with an Erlang distribution. General closed form expressions for the lower and upper bounds of outage probability are derived for arbitrary channel length L as a function of end-to-end signal to noise ratio. This analysis is then extended for the case when single relay selection from an arbitrary number of relay nodes M is performed. The spatial and temporal cooperative diversity gain is then analysed. In addition, exact form of outage probability for multi-path channel length L = 2 and selecting the best single relay from an arbitrary number of relay nodes M is obtained. Moreover, selecting a pair of relays when L = 2 or 3 is additionally analysed. Finally, the third contribution context is outage probability analysis of a cooperative AF network with single and two relay pair selection from M available relay nodes together with clipping at the source node, which is explicitly modelled. MATLAB and Maple software based simulations are employed throughout the thesis to support the analytical results and assess the performance of algorithms and methods

Exploiting Diversity in Broadband Wireless Relay Networks

Fading is one of the most fundamental impairments to wireless communications. The standard approach to combating fading is by adding redundancy - or diversity - to help increase coverage and transmission speed. Motivated by the results in multiple-input multiple-output technologies, which are usually used at base stations or access points, cooperation commutation has been proposed to improve the performance of wireless networks which consist of low-cost single antenna devices. While the majority of the research in cooperative communication focuses on flat fading for its simplicity and easy analysis, in practice the underlying channels in broadband wireless communication systems such as cellular systems (UMTS/LTE) are more likely to exhibit frequency selective fading. In this dissertation, we consider a frequency selective fading channel model and explore distributed diversity techniques in broadband wireless relay networks, with consideration to practical issues such as channel estimation and complexity-performance tradeoffs. We first study a system model with one source, one destination and multiple decode-and-forward (DF) relays which share a single channel orthogonal to the source. We derive the diversity-multiplexing tradeoff (DMT) for several relaying strategies: best relay selection, random relay selection, and the case when all decoding relays participate. The best relay selection method selects the relay in the decoding set with the largest sum-squared relay-to-destination channel coefficients. This scheme can achieve the optimal DMT of the system at the expense of higher complexity, compared to the other two relaying strategies which do not always exploit the spatial diversity offered by the relays. Different from flat fading, we find special cases when the three relaying strategies have the same DMT. We further present a transceiver design and prove it can achieve the optimal DMT asymptotically. Monte Carlo simulations are presented to corroborate the theoretical analysis. We provide a detailed performance comparison of the three relaying strategies in channels encountered in practice. The work has been extended to systems with multiple amplify-and-forward relays. We propose two relay selection schemes with maximum likelihood sequential estimator and linear zero- forcing equalization at the destination respectively and both schemes can asymptotically achieve the optimal DMT. We next extend the results in the two-hop network, as previously studied, to multi-hop networks. In particular, we consider the routing problem in clustered multi-hop DF relay networks since clustered multi-hop wireless networks have attracted significant attention for their robustness to fading, hierarchical structure, and ability to exploit the broadcast nature of the wireless channel. We propose an opportunistic routing (or relay selection) algorithm for such networks. In contrast to the majority of existing approaches to routing in clustered networks, our algorithm only requires channel state information in the final hop, which is shown to be essential for reaping the diversity offered by the channel. In addition to exploiting the available diversity, our simple cross-layer algorithm has the flexibility to satisfy an additional routing objective such as maximization of network lifetime. We demonstrate through analysis and simulation that our proposed routing algorithm attains full diversity under certain conditions on the cluster sizes, and its diversity is equal to the diversity of more complicated approaches that require full channel state information. The final part of this dissertation considers channel estimation in relay networks. Channel state information is vital for exploiting diversity in cooperative networks. The existing literature on cooperative channel estimation assumes that block lengths are long and that channel estimation takes place within a fading block. However, if the forwarding delay needs to be reduced, short block lengths are preferred, and adaptive estimation through multiple blocks is required. In particular, we consider estimating the relay-to-destination channel in DF relay systems for which the presence of forwarded information is probabilistic since it is unknown whether the relay participates in the forwarding phase. A detector is used so that the update of the least mean square channel estimate is made only when the detector decides the presence of training data. We use the generalized likelihood ratio test and focus on the detector threshold for deciding whether the training sequence is present. We also propose a heuristic objective function which leads to a proper threshold to improve the convergence speed and reduce the estimation error. Extensive numerical results show the superior performance of using this threshold as opposed to fixed thresholds

Cooperative Relaying In Power Line Environment: A Survey and Tutorial

Exchange of information is essential in any society and the demand for faster, cheaper, and secure communications is increasing every day. With other hi-tech initiatives like IPv6 and Internet-of-Things (IOT) already in the horizon, demand for broadband is set to escalate beyond its current level. Inherently laden in the challenges posed by this technology are fresh opportunities in terms of penetration of data services into rural communities and development of innovative strategies for more efficient use of the grid. Though still in its developmental phase/stage, Power Line Communication (PLC) has grown beyond theoretical fantasy to become a reality. The proofs are the readily available PLC systems that can be purchased off the shelfto achieve in-house networking and the much talked about, smart metering technology; generally regarded as the “new bride” in utilities industry. One of the biggest gains of PLC is its use of existing electrical cables, thereby eliminating cost of installation and maintenance of data cables. However, given that the power infrastructure was traditionally built to deliver electricity, data signals do suffer various forms of distortions and impairments as they transit it. This paper presents a tutorial on the deployed wireless system technique which is to be adapted to PLC scenario for the purpose of managing the available source energy for achieving reliable communication system. One of these techniques is the cooperative diversity. Its application and deployment in power line environment is explored. The improvement achieved through cooperative diversity in some PLC systems were presented along with the associated limitations. Finally, future areas of research which will further improve the reliability of PLC systems and reduce its power consumption during transmission is shown

Cooperative diversity schemes for wireless communication systems

Mestrado em Engenharia Electrónica e TelecomunicaçõesA presente dissertação insere-se na área das comunicações sem fios, ou mais especificamente na temática da diversidade cooperativa. Neste trabalho é feito o estudo, implementação e avaliação do desempenho de esquemas de diversidade cooperativa de baixa complexidade para sistemas de comunicação móvel. Estes esquemas são mapeados em modelos de simulação baseados em OFDMA e são completamente simulados em CoCentric System Studio. Os resultados obtidos com os modelos desenvolvidos mostram que os esquemas de diversidade cooperativa atenuam os efeitos do desvanecimento induzido pela propagação multipercurso, aumentando desta forma a capacidade e cobertura dos sistemas wireless. Os ganhos são particularmente altos quando as perdas de percurso são consideráveis, como é o caso das zonas urbanas densas. ABSTRACT: This dissertation is inserted into the wireless communication, or more specifically, into the cooperative diversity field. within this thesis, the performance of low-complexity cooperative diversity schemes projected for mobile communication systems are studied, implemented and evaluated. These schemes are mapped into simulation models based on OFDMA and are fully simulated in the CoCentric System Studio environment. The obtained results show that the proposed cooperative schemes for the uplink communication mitigate fading induced by multipath propagation, thereby increasing the capacity and coverage of wireless systems. Cooperation gains are particularly high when multipath losses are considerable, as is the case for dense urban regions

Design of distributed space-time block codes for relay networks

The fading effect often faced in wireless communications can cause severe attenuation in signal strength. To solve this problem, diversity techniques (in terms of spatial/time/frequency) have been considered. For example, spatial diversity can be achieved by using multiple antennas at the transmitter or the receiver or both. One important architecture that can efficiently exploit the multiple antennas is the space-time block coding (STBC). The realization of STBC requires more than one antenna at the transmitter. Unfortunately, the use of multiple antennas is not practical in many wireless devices due to the size limitation. Recently, the “cooperative diversity”, also known as “user diversity”, enables single-antenna mobiles in a multi-user environment to share their antennas and generate a virtual multiple-antenna transmitter that allows them to achieve transmit diversity. To apply concept of the STBC schemes to the cooperative communications, Laneman et al. suggest the use of “conventional” orthogonal STBC in a “distributed” fashion for practical implementation of user cooperation. The pioneering works on distributed STBC (DSTBC) assume flat fading channels. This can be achieved by using multi-carrier techniques such as orthogonal frequency division multiplex (OFDM) to divide a whole spectrum into a set of narrower bands. Hence, the channel can be considered flat in each sub-band. However, for current wireless communications with single-carrier transmission, the frequency selective channels cannot be avoided. Thus, in this dissertation, I will consider the application of DSTBC to frequency selective fading channels. In the first part of my thesis, I present a new design of DSTBC to achieve full rate transmission and channel decoupling property as in conventional STBC by using zero-padding (ZP). Several receiver techniques in frequency domain are studied for the signal detection of the proposed DSTBC. The extension from ZP to unique-word (UW) will be proposed in the second part. Exploiting the properties of the UW, I will present in the third part of my thesis a method of channel estimation for relay networks

Channel estimation and parameters acquisition systems employing cooperative diversity

Doutoramento em Engenharia Eletrotécnica e TelecomunicaçõesThis work investigates new channel estimation schemes for the forthcoming and future generation of cellular systems for which cooperative techniques are regarded. The studied cooperative systems are designed to re-transmit the received information to the user terminal via the relay nodes, in order to make use of benefits such as high throughput, fairness in access and extra coverage. The cooperative scenarios rely on OFDM-based systems employing classical and pilot-based channel estimators, which were originally designed to pointto-point links. The analytical studies consider two relaying protocols, namely, the Amplifyand-Forward and the Equalise-and-Forward, both for the downlink case. The relaying channels statistics show that such channels entail specific characteristics that comply to a proper filter and equalisation designs. Therefore, adjustments in the estimation process are needed in order to obtain the relay channel estimates, refine these initial estimates via iterative processing and obtain others system parameters that are required in the equalisation. The system performance is evaluated considering standardised specifications and the International Telecommunication Union multipath channel models.Este trabalho tem por objetivo o estudo de novos esquemas de estimação de canal para sistemas de comunicação móvel das próximas gerações, para os quais técnicas cooperativa são consideradas. Os sistemas cooperativos investigados neste trabalho estão projetados para fazerem uso de terminais adicionais a fim de retransmitir a informação recebida para o utilizador final. Desta forma, pode-se usurfruir de benefícios relacionados às comunicações cooperativas tais como o aumento do rendimento do sistema, fiabilidade e extra cobertura. Os cenários são basedos em sistemas OFDM que empregam estimadores de canal que fazem uso de sinais piloto e que originalmente foram projetados para ligações ponto a ponto. Os estudos analíticos consideram dois protocolos de encaminhamento, nomeadamente, Amplify-and-Forward e Equalise-and-Forward, ambos para o caso downlink. As estatísticas dos canais em estudo mostram que tais canais ocasionam características específicas para as quais o filtro do estimador e a equalisação devem ser apropridamente projetados. Estas características requerem ajustes que são necessários no processo de estimação a fim de estimar os canais, refinar as estimativas iniciais através de processos iterativos e ainda obter outros parâmetros do sistema que são necessários na equalização. O desempenho dos esquemas propostos são avaliados tendo em consideração especificações padronizadas e modelos de canal descritos na International Telecommunication Union