A 300-800MHz Tunable Filter and Linearized LNA applied in a Low-Noise Harmonic-Rejection RF-Sampling Receiver

A multiband flexible RF-sampling receiver aimed at software-defined radio is presented. The wideband RF sampling function is enabled by a recently proposed discrete-time mixing downconverter. This work exploits a voltage-sensing LNA preceded by a tunable LC pre-filter with one external coil to demonstrate an RF-sampling receiver with low noise figure (NF) and high harmonic rejection (HR). The second-order LC filter provides voltage pre-gain and attenuates the source noise aliasing, and it also improves the HR ratio of the sampling downconverter. The LNA consists of a simple amplifier topology built from inverters and resistors to improve the third-order nonlinearity via an enhanced voltage mirror technique. The RF-sampling receiver employs 8 times oversampling covering 300 to 800 MHz in two RF sub-bands. The chip is realized in 65 nm CMOS and the measured gain across the band is between 22 and 28 dB, while achieving a NF between 0.8 to 4.3 dB. The IIP2 varies between +38 and +49 dBm and the IIP3 between -14 dBm and -9 dBm, and the third and fifth order HR ratios are more than 60 dB. The LNA and downconverter consumes 6 mW, and the clock generator takes 12 mW at 800 MHz RF.\ud \u

A Compact Semi-Lumped Tunable Complex Impedance Transformer

International audienceThis article describes the design and performance of a compact tunable impedance transformer. The structure is based on a transmission line loaded by varactor diodes. Using only two pairs of diodes, the circuit is very small with a total length of only λ/10. Both the frequency range and the load impedance can be tuned by varying the varactor bias voltages. Our design provides a tunable operating frequency range of ± 40% and an impedance match ranging from 20 Ω to 90 Ω at 0.8 GHz and from 30 Ω to 170 Ω at 1.5 GHz. In addition, a new approach that considers losses for the simulation and measurement of this impedance transformer was investigated. The measured performance of a 1 GHz prototype design confirmed the validity of this new approach

Design of Programmable Phase Shifters and Attenuators in 130nm CMOS Technology

This thesis proposes the analysis and design of a phase shifter and a programmable attenuator for Doherty Power Amplifier (DPA) application, using the Infineon 130nm CMOS technology. The DPA is an architecture often used in nowadays cellular base-stations and the control of phase and amplitude in this system allows to optimize its efficienc

Co-design of Reconfigurable and Multifunction Passive RF/Microwave Components

In order to meet the market demands, multi-band communication systems that are able to accommodate different wireless technologies to be compatible with different wireless standards should be investigated and realized. Multifunction and multi-band RF front-end components are promising solutions for reducing the size and enhancing the performance of multi-band communication systems. This dissertation focuses on the design and implementation of different multifunction and tunable microwave components for use in multi-standard, flexible transceiver. For frequency-domain duplexing (FDD) communication systems, in which the uplink and downlink channels are carried on different RF frequencies, a diplexer is an essential component to separate the transmitting and receiving signals from the antenna. Electrically tunable diplexers simplify the architecture of reconfigurable RF-front end. Moreover, in modern communication systems, the crowding of the spectrum and the scaling of electronics can result in higher common-mode interference and even-order non-linearity issues. In this dissertation, three tunable compact SIW-based dual-mode diplexers, with various SE (single-ended) and BAL (balanced) capabilities, are introduced for the first time. The dual-mode operation results in a dependent tuning between the two ports. The presented designs are for SE-SE, SE-BAL, and BAL-BAL. However, based on the presented design concepts, any combination of the diplexer ports can be achieved in terms of supporting the balanced and single-ended system interface. The fabricated diplexers show low insertion loss, high isolation, good tuning range and high common mode rejection. Tunable bandstop filter (BSF) is one of the essential components in the design of RF front-ends that require wide-band operations. A wide-open front-end leaves the receiver vulnerable to jamming by high-power signals. As a result, this type of front-ends requires dynamic isolation of any interfering signal. Realization of such filters in a balanced configuration, as a second function, is an important step in the realization of full-balanced RF front-ends. Balanced (differential) circuits have many important advantages over unbalanced (single-ended) circuits such as immunity to system noise, reduction of transient noise generation and inherent suppression of even-order nonlinearities. All reported balanced filters are bandpass filters that target wide pass-bands and high common-mode rejection. These filters are necessary for wide-band RF front-ends but, as mentioned above, leave the system open to interferers and jammers. In this dissertation, a new differential coupling structure for evanescent-mode cavity resonators is developed, enabling the design of fully-balanced tunable BSF. The proposed filter is tunable from 1.57-3.18 GHz with 102% tuning range. In addition, over the full range, the measured 10-dB fractional bandwidth ranges from 1-2.4%, and the attenuation level is better than 47 dB. Lastly, Substrate Integrated Waveguide (SIW) evanescent-mode cavity resonators (EVA) are employed in the design of RF couplers, quadrature hybrid and rat-race couplers. These couplers are used in the design of numerous RF front-end components such as power amplifiers, balanced mixers, and antenna array feeding networks. Utilizing such resonators (EVA) in the design allows the couplers to have wide spurious-free range, low power consumption, high power handling capability and both tunability and filtering capabilities. The proposed quadrature hybrid coupler can be tuned starting from 1.32–2.22 GHz with a measured insertion loss range from 1.29 to 0.7 dB. The measured reflection and isolation are better than 12 dB and 17 dB, respectively. Moreover, the coupler has a measured spurious free range of 5.1–3fo (lowest–highest frequency). Regarding rat-race coupler, two designs are introduced. The first design is based on a full-mode cavity while the second one is more compact and based on a half-mode cavity. Both designs show more than 70% tuning range, and the isolation is better than 30 dB

A Novel Method for Tuning a Transistor-Based non-Foster Matching Circuit for Electrically Small Wideband Antennas

This dissertation reviews the application of non-Foster circuits for wideband antenna matching, and introduces a novel, rapid means of “tuning” the circuit to accommodate variations in antenna loadings. The tuning is accomplished via the judicious addition of a common transistor.A detailed literature search is provided, and non-Foster circuits are discussed in detail, including the myriad of implementations with focus on tuning. A comparison between different tuning methods is presented. The novel tuning method is evaluated via the normalized determinant function to ensure stability. Evaluations include simulations using commercially available software and experimentation to ensure not only stability but also that noise added by the active circuitry is manageable. Wideband stable operation is confirmed by pairing the tunable non-Foster matching circuit with an electrically small, resistively loaded dipole, and performance gains are demonstrated using the tunability feature. The resistively loaded dipole alone demonstrates reasonable performance at higher frequencies, but performance degrades considerably at lower frequencies, when the dipole is electrically small. The tunable non-Foster circuit is shown to alleviate some of this degradation. Additionally, applications other than wideband antenna matching can benefit from tunable non-Foster circuits such as tunable filters and phase shifters, and these are discussed as well. Finally, practical limitations of non-Foster circuits are presented